Universal Ubiquitous OS-M340Q1-0G0G-R02WFC Installation and operation manual

PRODUCT
BOOKLET

OS-M340Q1-0G0G-R02WFC
Product
number
OS-M340Q1-0G0G-R02WFC
(Pictures for reference only, subject to our products)

Device introduction
Parts list
Dimensional drawing
Platform/Software
operating instruction
Appearance description
Position
Height
Steps
Wiring connection
Product description
Features
FAQ
Illumination intensity
Parameters
Parts List QuantityNo. Name
1 1Uface host
2 1DC 12V power adapter, white sockets
3 1Support, wall stickers
4
5
1
3
Countersunk screws, L-type hexagon screw driver
Expansion pipe, self-tapping screws
Parts list
Dimensional drawing
Dear customer:
Thank you for using our product. For better use, please carefully read this instruction. If you have any
issues not mentioned here, please contact the provider. All parts of this booklet are reserved by our
company, including words, pictures and graphics. Without written permission, no unit or individual
shall extract, copy, translate or edit the content in this instruction.
Support
Device
90.00
66.00
60.00
185.24
2.00
21.20
80.00
158.00
Unit: mm
RGB camera
Thermal via
Support slot
Thermal via
Net mouth
Infrared
camera
Infrared
filling light
Wiring extension socket
Screw hole for
the support
Tamper switch
The software carried by the device divides into 2 versions: GS (WO platform, provides the secondary
development) and LAN (LAN or offline version, provides the secondary development). Please mark the need
for software version when place the order. Please contact the customer service if another version required.
For more detailed platform/software instruction manual, please login into the official website to download or
contact the customer services.
Platform/Software operating instruction
Appearance description
Instruction
1 / 2
1 3 5 7 9 11 13 15
2 4 6 8 10 12 14 16
POWER
GNDDC 12V
Power polarity. If
the polarity is put
in the opposite
position, the
device will not be
booted. The
power adapter
requires DC
12-DC 16V/2A
IO OUT
NO COM
Series signal
output. Serial
communication
TXD wiring end and
RXD wiring end
(Pictures for reference only, subject to our products)
COM PORT
GND
Wiegand 26/34
signal output.
Wiegand signal 0
output end and 1
output end
RS-485 serial signal
output
Alarm signal input
ALARM INPUT
ALARM
-IN1
ALARM
-IN2
Relay digital signal
output. From left to
right are: normally
closed contact,
normally open
contact and public
end. Connect the
wires according to
specific needs
COM PORT WG OUT
RS-232
RXD
RS-232
TXD GND WD0 WD1 GN0 NC RS-485+ RS-485-
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

The recognized face, of which, the illumination
intensity (” intensity “ in short) shall not be lower
than 30 Lux. The device has filling light itself, so
when the device put in a totally dark environ-
ment, the face illumination intensity, 0.5m
distance to the device, is about 100 Lux. The
nearer to the device, the higher the intensity is.
If there is overexposure on the face, the face
characteristics will be unable to be extracted
and may lead to hard recognition.
Light issues may lead to big differences between site
image and registered image; backlight, side-light and
strong light will influence the recognition experience.
(Analysis: from the view of human eyes, the color
changes on face skin may result in wrong recognition
of identity; unclear exposure area, no matter large or
small, may influence the identity judgement.)
The test standard is as shown on the picture:
the angle between dotted line A and dotted line
B is 90 ° , the test adopts the common light
meter with full spectrum, and applies U30 stan-
dard light source; adjust the distance between
source light and test object, subject to the
illumination intensity of the object’ s face at this
time.
Back light
Intensity test
Illumination intensity in actual scenarios
Strong light
Side light
Light source is near the object
Device stands between
the light source and object
Object stands between the
device and light source
Side-light may lead to
uneven light on the face
Backlight may make the
face too dark
Direct strong light may
cause overexposure
500Lux,
overexposure
30 Lux, dim
100 Lux, bright
50 Lux, normal
300 Lux, slight
exposure
Reference to intensity
Illumination intensity
1. Install the device in a place with little
impact from light source.
2. Add a registered image according to the
site condition.
3. Properly lower the threshold value
according to usage.
Improvements
Device
0.5m~1m
d
90°
Test object
Light source
A
B
When the sunlight shines indoor through the window, the face
recognition terminal device shall not be installed in shown black
shadow area, instead, shall be installed in place with little
sunlight impact, no side-light and no backlight. (Glass window
can be seen as no walls)
Sunlight shines indoor
If the room has glass window, there is no shield for sunlight,
then it is suggested to hang curtains over the window, and
install the device in place with shield to avoid direct sunlight
influencing the recognition. (Glass wall can be seen as no walls)
Glass window
Sunlight shines through the door, the device shall be installed at
the place with shields and little light impact. Glass window can
be seen as no shields, so the device shall be installed at the side
without glass window or with curtain hung.
Sunlight shines through the door, with glass window at
one side
Sunlight shines through the door, the device shall be installed at
the place with shields and little light impact.
Sunlight shines through the door
Suggested installation height is
1.4m，as the recognizable body
height range, 0.5m distance away
from the device, is 1.3m-1.7m;
the recognizable body height
range, 1m distance away from
the device, is 1m-2m. (There are
some deviations)
Camera vertical wide-angle Camera horizontal wide-angle
Wall
1.4m
Device
Wall
User
2m
Recognition area
Position 3 / 4
Height
Indoor
Door
Light
Wall/Shields
Indoor
Door
Light
Wall/Shields
Indoor
Door
Door
Wall/Shields
Indoor
Door
Wall/Shields
Glass wall
Light
Light
Glass window (same as the semi-outdoor scene
with no walls)
Device Light
DoorWall
Person
Curtain
Device shall be installed in places avoiding backlight, side-light and strong light.
This place, 3m away from the window, or does not
influenced by sunlight, can be considered for installation.
FOV(V)
FOV(H)
Backlight, side-light or direct strong light, not
suitable for installation.
Other areas, install in suitable places according
to actual light impact.

Wiring instruction (set power wire as an example, the rest can be done in the same manner)
Take off the protection circle
on the pre-stripping wire of
socket cable
1
6
4
2Paste hole papers, and keep the horizontal line parallel with the ground and the red line 1.4m
distance to the ground. Drill 3 screw holes on the wall according to the reminder of hole paper,
drill 2 outlet holes according to wiring needs, please use expansion pipe in the parts to knock
into the hole if for wall with hard foundation.
3
According to the support position, punch out the white
socket with connected wires from the outlet hole.
Move the support to align the 3 holes on it with holes on the wall, and use the screws to fix
the support on the wall.
5Align the white socket with interface on the device back, and insert.
Twist the countersunk screw around the device, align the slot at the device bottom with the
hook at the support bottom, use hexagon tool or hexagonal screwdriver to tighten the
countersunk screws follow the direction indicated, to complete the installation.
Attention: If the polarity of the power cable is connected in opposite direction, then the device will not be booted; if connected in
right direction, then the device will be normally booted; power adapter requires DC12-16V, 2A
Attention: If the wall has hard foundation, self-tapping screws shall be used together with expansion pipe; if the wall has soft
foundation, use self-tapping screws directly.
Steps 5 / 6
Use tool like scissor to strip
(power) cable, and expose the
metal wires
Twist the positive pole of the power cable with
corresponding metal wire, and use black tape to
cover the metal part
Pre-stripping
Countersunk screw Slot
Wall
Ground
1.4m Expansion pipe screw
86-type
cassette
hole
Wall-mount stickers
1.4m calibration tail
Drill here Drill here
Drill here
86-type
cassette
hole
86-type
cassette
hole
86-type
cassette
hole
86-type
cassette
hole
86-type
cassette
hole
Steps (on the wall):
1. Please followthe calibration tail, and paste
this sticker horizontally on the wall
2. Please followthe marker, and drill the holes
3. Remove the sticker, and install the device
When there is no
86-type cassette,
please drill hole here
as the way out for
power cable and
network cable)
Outlet hole
86-type
cassette
hole
Wall-mount stickers
1.4m calibration tail
Drill here Drill here
Drill here
86-type
cassette
hole
86-type
cassette
hole
86-type
cassette
hole
86-type
cassette
hole
86-type
cassette
hole
Steps (on the wall):
1. Please followthe calibration tail, and paste
this sticker horizontally on the wall
2. Please followthe marker, and drill the holes
3. Remove the sticker, and install the device
When there is no
86-type cassette,
please drill hole here
as the way out for
power cable and
network cable)
86-type
cassette
hole
Uface C Wall-mount stickers
1.4m calibration tail
Drill here Drill here
Drill here
86-type
cassette
hole
86-type
cassette
hole
86-type
cassette
hole
86-type
cassette
hole
86-type
cassette
hole
Steps (on the wall):
1. Please followthe calibration tail, and paste
this sticker horizontally on the wall
2. Please followthe marker, and drill the holes
3. Remove the sticker, and install the device
When there is no
86-type cassette,
please drill hole here
as the way out for
power cable and
network cable)

Installation notes
1、Cables inside of the touch switch board shall keep far away from the center area of the board back.
2、When arrange the wires, if the 12V power supply cable of the host does not adopt the “Special power
strip” and is in long distance, resulting in large resistance, then abnormal phenomena may occur easily such
as insufficient voltage, repeat restart, system crash and so on.
3、The power adapter with the device is shown as follow, 1m length in total, with 40cm low voltage power
cable and 40cm high voltage power cable.
V
1m
40cm 40cm
(Pictures for reference only, subject to our products)
Power cable (weak current) 12-16V, 2A Power cable (strong current) 220V
Extension of power cable (weak current) can not exceed 2m, otherwise, it may cause insufficient
power supply for the host end, and abnormal phenomena like repeat restart, system crash and so
on may occur. If the power is far away from the device, the power cable can be extended (strong
current).
If use other power adapter, 9V 1A as an example, then insufficient voltage and too weak current
may cause repeat restart.
The cable cannot be too fine (such as network cable and fine line), it is suggested to connect
multi-strand cable in parallel or use copper core bold cable, to ensure voltage >11V.
Attention: If use network cable, the extension cable uses 4-strand cable as positive pole and 4-strand cable as negative pole.
If not clear with how to extend, please contact the provider to change “Special power strip”.
Terminal host
Power
GND
12V
Cable equivalent
resistance1
Cable equivalent
resistance2
Voltage meter
Sensor
DC+
DC-
NO
COM
Wiring connection 7 / 8
Wiring for magnetic door Wiring for automatic door
System installation schematic
drawing for magnetic door
Wiring schematic drawing for touching
switch of magnetic door
System installation schematic
drawing for automatic door
Wiring schematic drawing for mechanical
switch of magnetic door
Wiring schematic drawing
for sensor switch of automatic door
Opening signal PUSH
Public end GND
12V
Controller of auto-door (only used terminals will be listed)
DC+
DC-
NO
COM
Terminal
host
门禁电源
Terminal
host
Auto-door controller
+ assembly units Sensor (inside)
DC12V Wired or
Wi-Fi
~220V
Door exit
(inside)
Magnetic lock
Power
Terminal host
Wired or
Wi-Fi
~220V
PUSH
GND
12V
COM
NC
NO
12V
GND
NO
NC
COM
﹣12V
﹢12V
Power
Door exit
Magnetic lock
Terminal host
1 3 5 7 9 11 13 15
2 4 6 8 10 12 14 16
12V NO
COM
GND
For detailed definition of the pin, please refer
to the appearance description For detailed definition of the pin, please refer
to the appearance description
For detailed definition of the pin, please refer
to the appearance description
1 3 5 7 9 11 13 15
2 4 6 8 10 12 14 16
12V NO
COM
GND
NO
NC
COM
Door exit
PUSH
GND
12V
COM
NC
NO
﹣12V
﹢12V
Terminal host
Magnetic lock
1 3 5 7 9 11 13 15
2 4 6 8 10 12 14 16
12V NO
COM
GND
Right Wrong

9 / 10
• Try to restart and reset
When the device stops in some interface for a long time, users can plug out the power switch,
power-on reset and then restart. If it does not take effect, then can long press RESET hole for
8-12s to restart the device. Besides, users can contact our staff and make some feedback.
• Protection
This device possesses certain protection capability which can prevent small objects (such as tools,
cables and so on) from entering and touching internal parts.
• Drop resistance
Please avoid operations such as falling, breaking, bending, heavily pressing and so on.
• Cleaning
Please use soft cloth or such materials lightly wipe the display screen or panel, and to avoid
scrubbing with water and cleaner.
• Low-temperature environment
The normal working temperature for this device is 0℃~50℃, if the actual temperature exceeds this
range, that may influence the normal use of the device.
FAQFeatures
油Do not dirty or damage the display screen
with oil-water or sharp objects
Do not use unknown power adapter to
avoid burning out the device
• Characteristics
• Store 10-thousand level database in local
• Quick recognition speed
• Secondary development (integrated)
• Complete functions
• High extensibility
Completely resolves image frauds in all kinds of carriers with infrared and RGB dual-camera dynamic
anti-forgery; when face database is 5000, the recognition accuracy is 99.99% (99.77% recognition
rate under 1% false accept rate; 99.27% recognition rate under 0.1% false accept rate).
(a) Device using cloud platform supports storing 5 thousand pieces of face images (smaller than
400KB), 1 million pieces of recognition records (0.45KB) and about 10 thousand pieces of site capture
images; (b) Device using LAN supports storing 5 thousand pieces of face images (each image calculat-
ed by 100KB) and 1 million pieces of recognition records (including the latest 10 thousand pieces of
site capture images).
(a) Face recognition takes around 150ms; (b) Extraction of face features takes around 330ms; (c) Face
comparison takes around 2ms (5-thousand level face database, with multiple comparison and
calculate the average value).
Supports the interface connection in HTTP; supports 232 and 484 serial output, Wiegand 26 and 34
output, custom the configuration of output content.
Supports recognition distance configuration; supports stranger detection; supports saving site
images of face recognition and stranger detection.
Supports deployment methods like public network and LAN; supports screen display content configu-
ration.

CE Caution:
Use the Product in the environment with the temperature Between -10℃and 50℃; Otherwise, it
may damage your product. Products can only be used below 2000m altitude
For the following equipment:
Product Name: Face recognition terminal
Model: UFACE-M4206-IC, M4206-IC, M4206-IC(White), M4206-IC(Black), M4206-IC-TP
Trade Name:
Universal Ubiquitous Co.,Ltd.
E-mail: [email protected]
Adapter shall be installed near the equipment and shall be easily accessible.
Only can use adapter as below:
Power Adapter Model: XED-RZ120200S
Input: AC100-240V, 0.6A, 50/60Hz; Output: DC12V, 2A
SHENZHEN XED POWER SUPPLY CO., LTD
The plug considered as disconnect device of adapter.
This product is intended for sale and application in a business environment.
RED Article 10 2
-This product can be used across EU member states
RED Article 10 10
-The product is class 1 product, No restrictions
The RF distance between body and product is 20cm
Bluetooth Version: V4.0
Frequency Range: 2402-2480MHz
Max. RF Output Power: 2.57dBm (EIRP)
Wi-Fi (2.4G)
Support Standards: 802.11b, 802.11g, 802.11n-HT20/40
Frequency Range:
2412-2472MHz for 802.11b/g/n(HT20); 2422-2462MHz for 802.11b/g/n(HT40)
Max. RF Output Power: 14.64dBm (EIRP)
NFC
Frequency Range: 13.56MHz
Radiated H-Field: -2.49dBuA/m(@10m)

FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement:
The transmitter must not be colocated or operated in conjunction with any other antenna or
transmitter. This equipment complies with the FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a minimum
distance of 20cm between the radiator and any part of your body.