urban ambiance UQL1252 User manual

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: LED 16W
Estimated Assembly Time: 30-45 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
1of2
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
A
Hardware Contents
Fixture Body
x1
AA
BB
CC
DD
EE
FF
II
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
Nipple
x1
Canopy
Chain Loop
x1
Canopy Lock
Ring
x1
Ceiling
Canopy
x1
GG Fixture Chain
x1
HH Quick Link
x2
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw AA
STEP 2 Install Canopy Chain Loop and Nipple-
*Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end
of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).
Place another Lock Washer (BB) over the Nipple (DD) and then
thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD)
is about 0.375” above the Crossbar (AA).
(Step 2 Continued)
C. Remove the Canopy Lock
Ring (FF) from the Canopy
Chain Loop (EE). Place the
Ceiling Canopy (II) over the
Canopy Chain Loop (EE)
against the ceiling to
determine the correct position
of the Nipple (DD). Thread the
Canopy Lock Ring onto the
Canopy Chain Loop (EE).
Adjust the Nipple (DD) to
allow the Ceiling Canopy (II)
to rest against the ceiling
when held in place by the
Canopy Lock Ring (FF).
D. Remove the Canopy Lock
Ring (FF) and the Ceiling
Canopy (II). Tighten the Hex
Nut (CC) against the
Crossbar (AA) to secure in
place.
AA
BB CC Step B
Step A
DD
CC
BB
EE
II
FF Figure 2
Fixture
Loop
Supply
Wires and
Ground Wire
STEP 3 - Install Fixture Chain and
Ceiling Canopy
A. Adjust the Fixture Chain (GG) to
your desired length by removing the
links if needed.
Pliers is required for this step.
B. With the Fixture Chain (GG) not
attached to the fixture loop and the
Canopy Chain Loop (EE), pull the
supply wires through the Fixture
Chain (GG) alternating links. After
the wires are through the Fixture
Chain (GG), pull the Supply Wires
and the Ground Wire through the
Canopy Lock Ring (FF) and the
Ceiling Canopy (II) in order.
C. Attach one end of the Fixture Chain
(GG) to the fixture loop with one
Quick Link (HH). Lift the fixture and
Fixture Chain (GG) up and attach
the other end of the Fixture Chain
(GG) onto the Canopy Chain Loop
(EE) with another Quick Link (HH).
The fixture will now hang safely.
Close the chain loop at the Ceiling
Canopy Loop (EE).
D. Feed the Supply Wires and Ground
*
DD
EE
HH
II
GG
FF
HH
Figure 3
Installation Instructions: UQL1252
www.urbanambiance.com

2of2
(Step 3 Continued)
Wire through the Canopy Chain Loop (EE) and Nipple (DD) into the
Outlet Box. Cut the wires leaving approximately 8” of wire extending
from the Outlet Box.
E. Refer to Step 4 for wire connections.
F. Raise the Ceiling Canopy (II) and Canopy Lock Ring (FF) up the
Fixture Chain (GG) and over the Canopy Chain Loop (EE). Tighten
the Canopy Lock Ring (FF) onto the Canopy Chain Loop (EE) until
tight.
Suggested chain length for Ceiling height :
8’ ceiling : use 15 links of chain and 2 quick links
9’ ceiling : use 26 links of chain and 2 quick links
10’ ceiling : use 37 links of chain and 2 quick links
Figure 4
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
White wire
from supply Ribbed side of wire from fixture
identified with the Label “N”
Black wire from
supply (or Red)
Smooth side of wire from fixture
identified with the label “L”
Ground wire
from supply
Ground wire
from fixture
Your fixture is now assembled and ready to use. Enjoy!
HOW TO REPLACE GLASS PANELS
A. Fixture Hood. Separate Quick Connector
and then remove Cage with Glass Panels from the fixture.
B. Unscrew Screws from the Cage and remove LED Module and Heat
Sink.
C.
Unlock Allen Screws on the
Unscrew Lock Screws on the LED Module. Replace the LED Module
with the replacement. Pass Lock Screws through the replacement
LED Module, the Heat Sinks as shown and thread Hex Nuts onto
Figure 6
SKU: UQL1252
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
PART NUMBER
1
NO. PART NUMBER REPLACEMENT PART REQ.
UQL1252CH 1
CHAIN
5” Dia.
9.5” SQ.
14.5”
2
116” OVERALL
HEIGHT INCLUDES
96” CHAIN AND
2 QUICK LINKS
(
)
2UQL1252PA 4GLASS PANEL
1
STYLE NUMBER
HOW TO REPLACE GLASS PANELS
Allen
Screw
Glass Panel
Cage
A.
Fixture Hood. Separate
Quick Connector and then
remove Cage with Glass
Panels from the fixture.
B. Unscrew Screws from the
Cage and remove LED
Module and Heat Sink,
Glass Holders. Replace
Glass Panels from the Cage
and then re-install Glass
Holders, LED Module and
Heat Sink. Secure with
removed Screws.
C. Connect Quick Connectors.
Attach Cage with Glass
Panels back onto the Fixture
Hood and secure with Allen
Screws.
Unlock Allen Screws on the
Figure 5
Glass Holder
Fixture Hood
LED Module
and Heat Sink
Quick
Connector
Screw
Allen Screw
Fixture Hood
Screw
LED Module
Quick
Connector
Cage with
Glass Panels
Lock Screw
Heat Sink
Hex Nut
Lock Screws to secure them
together. Hand tighten until
snug.
D. Pass the Quick Connector
from the LED Module
through the hole on the Heat
Sink.
E. Re-install LED Module and
Heat Sink onto the top edge
of the Cage. Secure with
Screws. Connect Quick
Connectors. Attach Cage
with Glass Panels back onto
the Fixture Hood and secure
with Allen Screws.
Upper
Heat Sink
www.urbanambiance.com