urban ambiance UQL1413 User manual

Package Contents
Warnings and Cautions
1of2
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
AInner Backplate
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBaseBulb100WMaximum,MediumBaseVintageBulbisrecommended,bulbnotincluded.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Fixture Body
x1 C
BLock Screw
x2
STEP 2 Reverse backplate if necessary-
A. Remove small hex nuts and small lock washers from the back of the
backplate.
B. Loosen the hex nut with lock washer and do not remove them.
C. Push the backplate as the arrow until the backplate and the bracket
are separated. Reverse the backplate.
D. Place the backplate back onto bolts on the bracket and secure with
Small Hex Nut
Small Lock Washer
Hex Nut with
Lock Washer
Bracket
Bolt
Backplate
Figure 2
Backplate
Backplate
PUSH
REVERSE
TOP VIEW
FRONT VIEW
(Step 2 Continued)
previously removed small lock washers and small hex nuts. Hand
tighten until snug.
E. Tighten the hex nut with lock washer and hand tighten until snug.
STEP 1 Remove Papers Inside of the Cage-
A. Rotate the bolt and remove it from the bolt holder to open the door.
B. Remove papers inside of the cage.
C. Close the door and place the bolt back onto the bolt holder.
Figure 1
Door
Bolt
Bolt Holder
Paper
(Remove)
Outlet Box
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
A
Mounting Hole
STEP 3 Installing the Inner Backplate-
A. Pass the supply wires through the Inner Backplate (A). Attach the
Inner Backplate (A) to the outlet box with two mounting holes on the
side. Secure the Inner Backplate (A) with outlet box screws (not
included). Tighten until snug.
Figure 3
Installation Instructions: UQL1413
www.urbanambiance.com

2of2
B
A
C
Backplate
STEP 5 -Install the Fixture Body
A. Place the backplate of the Fixture Body (C) onto the Inner
Backplate (A) and secure with Lock Screws (B). Hand tighten until
snug.
Figure 5
STEP 4 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 4
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
STEP 6 -Install Bulb
A. Rotate the bolt and remove it from the bolt holder to open the door.
B. Insert the bulb onto the socket and screw snugly into place.
C. Close the door and place the bolt back onto the bolt holder.
Door
Bolt
Bolt Holder
Vintage Bulb
(recommended
but not included)
Figure 6
Socket
FINISH: AGED COPPER
NOTE: ALL DIMENSIONS ARE
ROUNDED UP TO THE
NEAREST 1/4"
STEP 7 -Apply Silicone Sealer
A. Make sure the exterior wall surface and fixture backplate are free
of dirt before applying caulk. Using exterior grade caulk, caulk over
top of backplate and down both sides. Do not caulk the bottom of
the fixture backplate to ensure proper moisture drainage.
Your fixture is now assembled and ready to use. Enjoy!
Exterior
Grade Caulk
Exterior
Grade Caulk
Backplate
Figure 7
9.25”
7.75”
15.25”
8”
Fixture can only be
mounted in the
direction indicated
8”
15.5”
Fixture can
only be
mounted in
the direction
indicated
8”
4”
9.25”
www.urbanambiance.com
UQL1413