urban ambiance UQL1010 User manual

Nipple
B
D
E
1of2
Package Contents
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) Medium Base Decorative Filament 60W bulb (provided), Maximum 150W,Alternate bulb (1) CFLMaximum.
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
STEP 5 Attach Fixture Body to
Post
-
A. Coat the top 1” of the Post with
Clear Silicone Caulk (not supplied)
and position the Post Fitter onto
the Post. Be sure to seat it
completely, aligning the holes in
the Fitter with the 1/16” Pilot Holes
drilled into the Post.
B. Secure the Fixture to Post with (3)
Mounting Screws (A).
Your fixture is now assembled and
ready to use. Enjoy!
AMounting Screw
x3
Post
Post Fitter
Figure 5
Mounting Hole A
STEP 3 Drill Pilot Holes on Post-
A. Carefully fit the Post Fitter over the
end of the Post (not supplied),
making sure the Post Fitter is fully
seated.
B. Mark the drill point for the (3)
Mounting Screws, using (3)
Mounting Holes as reference. After
marking hole locations, remove
fixture from post and drill 1/16” pilot
holes for screws.
Figure 3 Post
Post Fitter
Mounting Hole
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
BFinial
x1
STEP 1 remove the
Ring from Fixture Body
-
A. Unscrew Lock Ball
and Lock Screw from
Fixture Body to
remove the Ring.
Figure 1
C
Waterproof
Washer
x1
D
Top
Cap
x1
E
Outer
Cap
x1
FBracket
x1
G
Fixture
Body
x1
HShade
x1
I
Edison
Bulb
x1
Fixture
Body
Ring
Lock Ball
Lock
Screw
STEP 2 Assembly Shade to
Fixture Body
-
A. This fixture uses Medium Base
Decorative Filament 60W bulb (I),
Maximum 150W. Insert bulb and
screw snugly into place.
B. Place the Shade (H) in to the
Fixture Body (G). Place the Ring,
the Bracket (F) over the Bolt on the
Fixture Body (G) properly, secure
by threading Lock Ball onto the
Bolt, hand tighten until sung.
C. Reinstall Lock Screw onto the
Fixture Body (G).
D. Place Outer Cap (E), Top Cap (C)
and Waterproof Washer (C) onto
the Nipple on the top of Bracket (E),
secure by threading Finial (B) onto
the Nipple. hand tighten until sung. Figure 2
F
H
G
Ring
Lock
Ball
Lock
Screw
C
www.urbanambiance.com
Installation Instructions: UQL1010

2of2
SKU: UQL1010
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
REPLACEMENT PART DESCRIPTION QTY.
NO.
1UQL1010SH SHADE 1
(1)Medium Base
Decorative
Filament 60W
bulbs (provided),
Maximum 150W.
10.5”
9”Dia.
6.5”Dia.
10.25”
19.25”
1
2UQL1010BU VINTAGE BULB 1
2
www.urbanambiance.com