Urbanears 04091226 User manual

3 ( Right side )
4 ( Right side )
HELLAS USER MANUAL ENG
PRODUCT OVERVIEW
1. Machine Washable Headband –
Detachable fabric headband for easy
wash and wear.
2. LED indicator – Discrete and unlit
during normal operation.
3. Built-in touch interface
4. Micro USB connector for charging
the battery.
SWITCH ON
Press and hold the touch interface
for 4 seconds
SWITCH OFF
Press and hold the touch interface
for 4 seconds.
CONNECTING TO A BLUETOOTH®
ENABLED SOUND SOURCE
Follow the steps below when pairing
your headphones with a sound source
(smart-phone, tablet or computer).
1. Make sure your headphones are
turned off.
1
2
NOTE! The headphones will auto
shut-off if inactive and disconnect-
ed for 10 minutes.
2. Press and hold the touch interface for
8 seconds to enter into pairing mode (fast
blinking blue LED light).
3. Select and connect to HELLAS on
your sound source, according to its user
manual.
After initial pairing, the two devices will
auto-connect when they are switched on
and within a range of 10 meters.

HELLAS USER MANUAL ENG
CHARGING
Plug your headphones into
a USB power source using
the micro USB cable. 2 hours
charge gives approximately
14 hours of playback time at
medium volume.
CONTROLS
The ear cups have a built-in swipe interface where you can answer calls, adjust volume
and switch tracks with a simple touch.
CLEANING THE
HEADPHONES
Detach the washable headband
and ear cushions and machine
wash at 30°C (cold/cool).
Clean the headphones with a
soft, dry cloth.
Play/Pause/Answer call
Single tap
Hang up/reject call
Double tap
Next song
Swipe forward
Previous song
Swipe backward
Increase volume
Swipe upward or press
and hold the upper part.
Decrease volume
Swipe downward or press
and hold the lower part.
NOTE! Charge the
battery before using
the headphones for the
first time.
NOTE! Do not use
liquids or sprays.

TROUBLE SHOOTING
Not powering on
Charge the headphones using the USB
cable. Make sure the headphones are
turned off before turning them on.
Not charging
Make sure the USB power source is
switched on. The LED indicator is red
while charging, and white when fully
charged.
Not pairing
Move the devices closer to each
other and away from any interference or
obstruction. The LED indicator is blue
and fast blinking when in pairing mode.
Make sure the headphones are not
connected to a different sound source
when attempting to pair. Disable and
enable Bluetooth® communication on
your sound source.
No sound
Make sure the headphones are on and
connected with your sound source.
Make sure the sound source is playing.
Not suitable for children under age three.
Contains small parts, which may be a
choking hazard.
Long-term exposure to loud music or
sounds may cause hearing loss. To
prevent possible hearing damage, do
not listen at high volume levels for long
periods.
This is not household waste. Instead it
shall be handed over to the applicable
collection point for the recycling of
electrical and electronic equipment.
Poor sound quality
Move the devices closer to each other and
away from any interference or obstruction.
IMPORTANT
SAFETY INSTRUCTIONS
• Set your sound source to low volume before
using the headphones.
• Do not use these headphones when oper-
ating a motor vehicle, bicycle, or machinery, or
when your inability to hear outside sound may
present a danger to you or others.
• Using these headphones limits your ability to
hear noises around you, regardless of listening
volume. Please use caution when using these
headphones.
• Do not drop or sit on the headphones or
allow them to be immersed in water.
• Keep headphones away from fire, water, and
high voltage equipment.
PLATTAN ADV WIRELESS USER MANUAL ENG
Red
Continuous
Battery charging
White
Continuous
Fully charged and
connected
to a USB power
source
Blue
Fast blinking
Pairing mode,
waiting to pair
Blue
Slow blinking
Waiting to connect
White
10s interval
Connected and
switched on
Off
Headphones are
switched off or in
normal operation
LED INDICATOR