USX-MOUNT XAS403-1 User manual

XAS403-1
INSTRUCTION MANUAL
For 13-27" TV
If you have any questions along the way, just give us a call
1-800-460-0956 or mail to [email protected].
We’re ready to help!
R

Before getting started, let’s check below lists to make sure it is just right for you!
2
3
4
2
Does your monitor
(including accessories)
weigh MORE than
17.6 lbs. (8 kg)?
Do you have
all the tools
needed?
(NOT INCLUDE) Tape
Measure
CAUTION
Screw
driver
No? Perfect – you may continue.
Yes? This mount is NOT compatible.
CAUTION: DO NOT exceed the maximum weight
indicated. This mounting system is intended for use only
with the maximum weights indicated. Use with products
heavier than the maximum weights indicated may result
in collapse of the mount and its accessories, causing
possible injury.
● Do not use this product for any purpose not explicitly specified by manufacturer
● Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
1
Check your monitor
VESA is within
Min and Max size
No? This mount is NOT compatible.
Yes? Perfect !
MAX:100mm/3.94"
(MIN:50mm/1.97")
MAX:100mm/3.94"
(MIN:50mm/1.97")
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety of the
installation, assembly or use of this product, please feel free to contact Customer
Service:
E-mail: [e-mail]
Phone call: 1-800-460-0956

3
3D
±360°
SIDE VIEW
+45°
-45°
FRONT VIEW
SIDE VIEW
FRONT VIEW
SIDE VIEW
440mm
[17.32in]
378mm
[14.88in]
100mm
[3.94in]
100mm
[3.94in]
399mm
[15.70in]
92mm
[3.62in]
406mm
[15.98in]
±90°
±90°
±90°

Never use damaged parts!
NOTE: Not all hardware included will be used.
4
-Monitor Connection x1
WARNING:This product contains small items that could be a choking hazard if swallowed. Before starting assembly,
verify all parts are included and undamaged.
Parts and Hardware for Monitor Installation
M4x12mm
M5x12mm
M6x12mm
M4/M5
M6
Washers
TV Screws
x4
x4
x4
x8
x8

Parts and Hardware for Monitor Arms Assembly
5
-Clamping Fastener x1-M5x15 Bolts x3
-3mm Wrench x1
-Rubber Mat x2
-Fastener x1 -M10x100 Handle X1 -Round Fastener x1
-5mm Wrench x1
-Pole folder x1
-Pole x1

6
Pole Unit

Use wrench to screw the clamping fastener to the pole by tightening the bolts .
Put the glued side of the rubber mat to the upper side of the clamping fastener .
2A-1 Assemble Pole Unit with Clamping Fastener
7
Pole Unit
Pole Unit-A

2A-2 Assemble Pole Unit-A on Desktop
MAX:3.85"
Fasten
Fasten pole unit-A on the desktop.
8
MIN:2.87"
Pole Unit-A
Desktop

2B-1 Assemble Pole Unit with Round Fastener
Use wrench to screw the round fastener to the pole by tightening the bolts .
Put the glued side of the rubber mat to the bottom of the round fastener .
9
Pole Unit
Pole Unit-B

2B-2 Assemble Pole Unit-B with Desktop
diameter of the hole
0.4-2.5”
Put pole unit-B to the hole on the upper desktop. Use Handle to tighten fastener and pole
Unit-B fully.
Fasten
10
Pole Unit-B
Desktop
Fully Tighten