UV-technik UVT 16 User manual

UV-Technik Speziallampen GmbH, Gewerbegebiet Ost 6, 98704 Wolfsberg
General Conditions for Sales and Supplies of UV-Technik Speziallampen GmbH are valid. Provision of a manual is mandatory.
20/04/2016 subject to change without notice product information UVT16 Hardware V2.1 Software V1.4
Page 1 of 8
Operation manual
UV-Monitor UVT 16

UV-Technik Speziallampen GmbH, Gewerbegebiet Ost 6, 98704 Wolfsberg
General Conditions for Sales and Supplies of UV-Technik Speziallampen GmbH are valid. Provision of a manual is mandatory.
20/04/2016 subject to change without notice product information UVT16 Hardware V2.1 Software V1.4
Page 2 of 8
UV - Monitor UVT 16 software version V1.4 article number: 321 00901 0002
Use
The UVT 16 Monitor is used to monitor signals from UV probes or
sensors applied to sources of radiation, providing a control system for
small items of UV equipment.
Description
The monitor is designed for installation on a control panel. At the rear
of the device are placed pluggable terminals for all connections. The
front plate contains the five keypads, three status LEDs and a two-line
alphanumeric display showing the metered values and other
information. The readings to be shown can be pre-selected from the
menu and/or called up by pressing the keypads. These pads are also
used to make the settings and to program the functions of the monitor.
The functionality of the software V1.4 is slightly enlarged in details but
apart from that identical with the previous version.
Technical data
Supply voltage
230 V AC 50 to 60 Hz; power taken up 2,5 W (110 V on request)
Size
W x H x D
Measurements for
installation
Casing for installation into control panel 96 x 96 x 64
Installed depth incl. clips 75 mm
Area of cut-out 92+0.8 x 92+0.8 acc. to DIN 43700
Installation method: screw-down clips
Connections
Two 14-pole push-on connections with screws to fix
Suitable wiring: 0.25 to 1.5 mm2cross-section
Display
Three status LED and alphanumeric two-line LCD display, with press-button illumination
LED thresholds: green > 70 %, yellow 70 % to 50 %, red < 50 %. Figures possible to display on LCD:
UV level, alarm, rate of flow, lamp life (in hours), overall operating hours, no. of switch-on cycles,
software version (All factory settings can be reset)
Operation
By means of 5 keypads on front of device
Temperature
Ambient temperature 0 to 40° C
Weight
Approx. 400 g
Inputs
- UV input via diode (can be set in two stages internally)
- Input for current loop sensors 4 to 20 mA, internal apparent ohmic
resistance 100 Ω
- Input for UV sensor with voltage output
options: max. 10 V; Ri = 50 KΩ
max. 5 V; Ri = 25 KΩ
max. 2 V; Ri = 10 KΩ
- Input for switch-on cycles: without potential, for (mains) 230 V AC signal
- Input, lamp failure (e.g. electronic ballast relay contact) Ie = 5 mA
- Input, alarm off –switch or button; alarm blocked during
servicing or maintenance
Outputs
- Output, 4 to 20 mA, can be set or calibrated using menu, apparent ohmic
resistance 100 Ω
- Supply voltage for voltage and current sensors:
(output voltage 24 V DC, will take max. 60 mA)
- Early warning, relay contact - closer
- Main alarm, changeover relay contact, contact will take
Imin = 50 mA at 5 V DC, Imax = 5 A at 250 V AC, resistive load
- RS 232 output on request
Additional functions
Integral meters for:
Overall operating hours (no reset possible)
No. of operating hours left for lamp (reset by operator possible)
No. of switch-on cycles (reset by operator possible)
“Change lamp” display
“Lamp failure” display
“Alarm” or “Early Warning” display.
All rights reserved in respect of technical amendments

UV-Technik Speziallampen GmbH, Gewerbegebiet Ost 6, 98704 Wolfsberg
General Conditions for Sales and Supplies of UV-Technik Speziallampen GmbH are valid. Provision of a manual is mandatory.
20/04/2016 subject to change without notice product information UVT16 Hardware V2.1 Software V1.4
Page 3 of 8
Connections
1/2: Input mains electricity 230 V AC
3/4/5: Output alarm 1 (changeover contact):
main alarm will take (current) at (resistance)
Imin = 50 mA at 5 V DC,
Imax = 5 A at 250 V AC
6/7: Output alarm 2 (closer): pre alarm
Threshold can be set from menu
Contact resistance levels as for main alarm
8/9: Input “alarm off”
When the switch/contact is closed, all
alarm signals are blocked
8/10: Input “lamp failure”: provided for connection of the electronic ballast contacts with no potential –
the lamp failure alarm is triggered on closure (Ie= 5 mA)
11/12: Input “switch-on cycles” input with no potential for a 230 V AC signal (i.e. lamp supply voltage): the
internal cycle meter goes up by 1 each time this voltage is switched on. The hours of operation are metered
continuously while the 230 V AC signal is being received. If the monitor is switched on simultaneously with
the lamps, and there is no separate electricity supply for lamps and monitor, this input must be provided
with mains voltage from contact nos. 1/2.
13/14: Output, supply voltage for voltage and current sensors: for hardware 2.1 and higher, 13 (-) already
connected internally to ground 21/26
15/16/17: RS 232 interface: this is for factory programming and can be programmed on request as an
optional extra
18/21: Output, 0/4 to 20 mA: for transmission of a standardised value over a considerable distance to an
external, higher-level control system (PLC)
19/20: Inputs, 0/4 to 20 mA: available for additional sensors, e.g. sensors to measure flow rate or
temperature (as optional extra)
21/26: Input Ground, equal to 26, internally connected to 13
22/23/24: Input for UV sensors with voltage output (DVGW/ÖNORM standard).
Supply voltage for these sensors is at output 13/14
25: Input for UV sensors with 0/4 to 20 mA current output (DVGW/ÖNORM)
26: Input Ground, equal to 26, internally connected to 13
27/28: Input for as many UV diodes as required; 2 sensitivity levels can be set by means of an internal
jumper –the factory setting is the high level, suitable for UV sensors based on silicon carbide, and if the
sensor is based on gallium phosphate or silicon the jumper setting must be changed; there is a menu for
calibration to match the lamp

UV-Technik Speziallampen GmbH, Gewerbegebiet Ost 6, 98704 Wolfsberg
General Conditions for Sales and Supplies of UV-Technik Speziallampen GmbH are valid. Provision of a manual is mandatory.
20/04/2016 subject to change without notice product information UVT16 Hardware V2.1 Software V1.4
Page 4 of 8
Assembly and commissioning
The monitor is designed to fit in an opening of 92+0.8 x 92+0.8 mm (W x H) on a control panel. The depth to be
provided for installation is approx. 75 mm including that for the cable connections. Screw-down clips are
supplied with the monitor to fix it. Please attach the clips top and bottom on the housing. To make the
connections sure against mix up they have different colours (right-orange, left-black). The electricity supply,
relay outputs and sensor are all connected up by plugs secured with screws and marked as appropriate.
Care is necessary with the polarity for the connection of the sensor. Care should be taken to avoid short
circuits, especially of the sensor supply voltage.
Input and output details
UV diodes and measured values given in %
UV diodes are connected to the terminals 27 (cathode) and 28 (anode). The factory setting is for use of
silicon carbide-based sensors (SUV 13A1C). If sensors based on silicon or gallium phosphate are to be used,
the jumper should be adjusted by the manufacturer. If the
customer does this, the method is as follows.
Disconnect the device from the mains! Remove both the 14-
pole push-in terminals. Unscrew the four screws on the rear
plate. Change the setting of the jumper indicated from
centre/top to centre/bottom. Then be sure to close the casing
before reconnecting to the main.
Sensor with voltage output, for W/m² metering, or
dosing (optional extra)
Sensors with voltage output (SUV 20.x x Y1C) are connected
as follows. The wires for the mains electricity are connected
to terminals 13 (-) and 14 (+). The sensor output must be
connected to terminal 24 (2V) and 26 (GND). If other sensors are used or the sensor at this input is
overloaded, terminals 23 (5V) or 22 (10V) can be employed.
Sensor with current output, metering in W/m²
Sensors with current loops (SUV 20.x x Y1C) are connected as follows. +UBfrom the sensor have to be
connected to terminal 14 (+), sensor output IOUT to terminal 25 (20 or 19 also possible). Connection 13 (-)
with 26 (GND) to close the current loop is already done internally.
sensor contacts
diode
Y1 –voltage output
Y2 –current output
cable Z1
cable Z3
pin 1
cathode (27)
signal output (23 resp. 24)
+ UB (14)
brown
yellow
pin 2
cathode (27)
GND (26 resp. 21)
+ UB (14)
white
brown
pin 3
anode (28)
- UB (13)
I out (25)
blue
green
pin 4
anode (28)
+ UB (14)
I out (25)
black
white
You can see in brackets the terminal numbers of the UVT16.
Including other sensors
The present software version supports only an additional sensor for rate of flow. The rate can be shown
additionally at the display. There is a choice of which input to use for it. Inputs are the ones 19/21 (Iin2) and
20/21 (Iin1) specifically intended for it. If Uin (or Iin) is not being used for a UV sensor, it can be used as an
alternative.
In case more functionality (e.g. dose calculation) is needed we refer to the UVT 18. This new developed
monitor comes with a more powerful hardware and allows on request also customer specified
programming.

UV-Technik Speziallampen GmbH, Gewerbegebiet Ost 6, 98704 Wolfsberg
General Conditions for Sales and Supplies of UV-Technik Speziallampen GmbH are valid. Provision of a manual is mandatory.
20/04/2016 subject to change without notice product information UVT16 Hardware V2.1 Software V1.4
Page 5 of 8
Displays, Operation, Programming
Using the keypads, navigating through the menus
Before monitoring starts, the apparatus must be adjusted to the particular external switching
circumstances. All values are easy to set using the five keypads provided of the front of the device. Each
time the keys are touched, the display will be illuminated for about one minute. This makes no difference
to the functioning of the keys.
Basic functions
►Arrow to right
EITHER moves cursor one place to the right OR diverts into sub-menu
◄Arrow to left
EITHER moves cursor one place to the left
OR diverts back to the higher-level menu without saving the value (effectively cancelling last entry) if
there is no option (or cursor for options) on extreme left
Central keypad (Enter)
Confirms, or accepts option, or accepts diversion into sub-menu
▲Arrow up
EITHER select option OR raise number at cursor position by one respectively shift comma one position
right
▼Arrow down
EITHER select option OR reduce number at cursor position by one respectively shift comma one
position right
before an entry indicates that it is possible to divert into a sub-menu
before an entry indicates that the next function is a choice of options
(Only in the Info Details menu, when the items in the basic display are selected)
–before an entry indicates that this item has been selected for the basic display.
+ before an entry indicates that this item has not been selected for the basic display.
To change these round, press the or ►keypads.
Brief guide to navigating
From the basic display, pressing ►brings up the first level of menus. If a password check has been
activated, the password will be requested.
By pressing ▲/ ▼, the user can browse through the menus, up / down, or can change the figure at the
cursor position respectively shift of the comma right / left.
The (Enter) key is pressed to confirm the current entry, or to execute the current menu item, or to divert
into the submenu. The ►key can also be used to divert into a sub-menu. Diverting will start always from
the marked line1. Line 2 shows a forecast or the value, which has to be changed. Within the value the
cursor can be moved right ►or left ◄to reach the position to be changed. If the cursor is already at the
extreme left, pressing the ◄keypad calls up the previous menu level (effectively cancelling the current
one). With pressing Enter the new entry will be stored.
If no keypad has been pressed for more than one minute, the display goes back to the basic display
automatically, and the light goes off. After this, if a password check has been activated, it will be necessary
to re-enter the password.

UV-Technik Speziallampen GmbH, Gewerbegebiet Ost 6, 98704 Wolfsberg
General Conditions for Sales and Supplies of UV-Technik Speziallampen GmbH are valid. Provision of a manual is mandatory.
20/04/2016 subject to change without notice product information UVT16 Hardware V2.1 Software V1.4
Page 6 of 8
Entering the password
A password will only be requested if the password checks in the program have been activated. The
password level is selected by means of the number before the "-" when the password is being entered.
1. is the level for authorised staff –limited authorisation
2. is the level for the plant engineer (unlimited access rights)
The device is supplied with both levels are switched off. To activate the password system, the entry “off” in
the Password menu must be replaced with a number between 001 and 255. The relevant users should note
the passwords well. If a password is forgotten after all, and typed in wrong, the display will show “Password
wrong; code: XX”. XX stands for two capital letters, which can be used to look up in a table a once-only
password. The manufacturer has the table to enable passwords 1 and 2 to be by-passed.
password 1
password 2
authorisation for staff with
level
description
No
No
no password
3
all have full access
No
Yes
no password
password 2
0
3
basic display only
full access
Yes
No
no password
password 1
0
3
basic display only
full access
Yes
Yes
no password
password 1
password 2
0
2
3
basic display only
access to basic functions*
full access
* password 1can be changed but not deactivated
LED-display / operating status
priority
status
LED
active relay
priority
status
LED
active relay
13
start test
-
6
sensor fault
!
main alarm
12
alarm off (m.)
!
-
5
lamp fault (8/10)
main alarm
11
main alarm (m.)
!
!
main alarm
4
main alarm
!
main alarm
10
pre alarm (m.)
!
!
pre alarm
3
pre alarm
!
pre alarm
9
internal fault ###
main alarm
2
life time alarm
-
8
delay ###,#
-
1
overload
!
-
7
alarm off (8/9)
!
-
0
normal operation
-
LED on
!
LED flashing

UV-Technik Speziallampen GmbH, Gewerbegebiet Ost 6, 98704 Wolfsberg
General Conditions for Sales and Supplies of UV-Technik Speziallampen GmbH are valid. Provision of a manual is mandatory.
20/04/2016 subject to change without notice product information UVT16 Hardware V2.1 Software V1.4
Page 7 of 8
Menu structure (Menu tree)
level
name menu item
kind of display
basic display
menu
monitor display
▼
+ info-state
display operation status
operation ok
▼
+ info-UV
display UV-value in % or W/m²
UV 083%
▼
+ info rate of flow
display rate of flow in m³/h
flow. 5,54m³/h
▼
+ info lamp hours
display remaining lamp hours
lamp 7.580h
▼
+ info overall hours
display operation hours of the monitor
all. 690h
▼
+ info switching cycle
display ON/OFF cycles
swcy 20
▼
+ info version
display software version
version 1.3-DE
0
1
2
main menu
menu
solicited input
►
▼
+ information
navigation: change with ■
►
▼
| + info state
+ not yet / - already chosen for basic display
■
▼
| + info-UV
+ not yet / - already chosen for basic display
■
▼
| + info rate of flow
+ not yet / - already chosen for basic display
■
▼
| + info lamp hours
+ not yet / - already chosen for basic display
■
▼
| + info-overall hours
+ not yet / - already chosen for basic display
■
▼
| + info switching cycles
+ not yet / - already chosen for basic display
■
▼
| + info version
+ not yet / - already chosen for basic display
■
►
▼
+ lamp
navigation: with ▲▼, ◄►, back without change ◄, confirm with■
►
▼
| + change lamp
decision yes / no
▲▼ + ■
▼
| + switching cycle
overwriting no. of switching cycles possible
value ►▲▼ + ■
▼
| + lamp hours
overwriting no. of remaining lamp hours possible
value ►▲▼ + ■
▼
| + life time lamp
Input/ overwriting of lamp lifetime hours possible
value ►▲▼ + ■
►
▼
+ alarm mode
navigation: selection with ■
►
▼
| + automatic
choose automatic function for alarm with
■
▼
| + manual alarm off
all alarm will be blocked with
■
▼
| + manual main alarm
tripping main alarm with (e. g. check higher level monitoring / buzzer)
■
▼
| + manual pre alarm
tripping pre alarm with (e. g. check indicator light / buzzer)
■
►
▼
+ alarm
navigation: selection resp. justify number ▲▼, positioning ◄►, Esc ◄, confirm ■
►
▼
| + manual duration
input duration of manual blocked alarm (0=endless)
value ►▲▼ + ■
▼
| + delay
input duration of alarm blocking after lamp ignition (run-up time)
value ►▲▼ + ■
▼
| + pre alarm
input threshold value pre alarm (%-value > main alarm value)
value ►▲▼ + ■
▼
| + main alarm
input threshold value main alarm (%-value < pre alarm)
value ►▲▼ + ■
▼
| + relay modus
relay closed/open while alarm
▲▼ + ■
▼
| + relay pre alarm
inactive/active while main alarm
▲▼ + ■
▼
| + relay lamp fault
relay closed/open in case of lamp fault
▲▼ + ■
►
▼
+ sensor-UV
navigation: selection resp. justify number ▲▼, positioning ◄►, Esc ◄, confirm■
►
▼
| + input
choose sensor input (diode, Uin, Iin, Iin1, Iin2)
▲▼ + ■
▼
| + calibration value
input value in % (diode) or W/m² (for sensors with option Y1/Y2)
►▲▼+ ■
▼
| + unit
choose unit %, W/m², J (for sensors with option Y1/Y2)
▲▼ + ■
▼
| + calibration
decision yes / no (for sensor diode e. g. type SUV13C)
▲▼ + ■
►
▼
+ sensor rate of flow
navigation: selection resp. justify number ▲▼, positioning ◄►, Esc ◄, confirm ■
►
▼
| + input
choose sensor input (Iin, Iin1, Iin2)
▲▼ + ■
▼
| + calibration value
input value in m³/h (=20 mA)
value ►▲▼ + ■
►
▼
+ output (Iout)
navigation: selection resp. justify number ▲▼, positioning ◄►, Esc ◄, confirm ■
►
▼
| + Iout-mode
choose mode 0 / 4 - 20 mA
▲▼ + ■
▼
| + maximum
input %-value for 20 mA
value ►▲▼ + ■
▼
| + minimum
input %-value for 0/4 mA
value ►▲▼ + ■
▼
| + calibration
DO NOT CHANGE ! (internal 20 mA calibration = St Iout on side sticker)
►
▼
+ change password
Input password 1 / 2- 001 ... 255 (000 password function inactive)
value ►▲▼ + ■
►
▼
+ store
save the adjusted cyclic order of the display information issues (the rest automatically)
■
Access authorisation level: 0=black (no restriction) 1=brown 2=green (partial access) 3=red (full access)

UV-Technik Speziallampen GmbH, Gewerbegebiet Ost 6, 98704 Wolfsberg
General Conditions for Sales and Supplies of UV-Technik Speziallampen GmbH are valid. Provision of a manual is mandatory.
20/04/2016 subject to change without notice product information UVT16 Hardware V2.1 Software V1.4
Page 8 of 8
Notes:
My standard values:
My standard circuitry:
Password 1 (plant user):
Password 2 (plant manufacturer):
Miscellaneous: