V-Count Nano User manual

Nano Quick Installation Guide
What Is Included in the Box?
• V-Count Nano 3D Sensor
• Label for cables
• 7 cm bracket
• USB-C type 5V 2A EU adaptor
Use only USB-C type 5V 2A adaptors to avoid sensor damage. Use a UPS to prevent
electronic damage and data loss from power cuts.
If you choose to use PoE, PoE Splitter is SOLD separately. Use only relevant PoE
switches and splitters that comply with the IEEE 802.3af standard as Nano's
maximum power requirement is 10W.
*You can set up your device using either Wi-Fi or a cable connection.
Alternative -1: Requirements for Installation with Wi-Fi
1. A mobile phone to connect and configure the sensor.
2. The username and password of the modem to connect to
the device.
3. The serial number located on the back of the device
4. Mobile app and its password - You can obtain the password
from our support.
5. Scan the QR code suitable for your operating system to
download the mobile app.
6. You can set up your device through the "Setup Sensor" menu,
under the "Profile" section on the mobile app.
*Please configure the Wi-Fi settings through our application,
not the local interface.
1. A laptop to connect and configure the sensor.
2. A PoE Splitter, in case a PoE switch is being used.
Please note that PoE is not included in the box; you may need to purchase it separately.
For information about PoE installation, please scan the QR code down below.
3. A laser meter to measure the ceiling height.
4. An Ethernet cable to connect the unit to the switch.
Ensure sufficient cable length from installation to switch point, not exceeding 90 meters
for CAT5/CAT6 cables.
5. An Ethernet crimp tool and a cable tester to check cable health.
6. A ladder to install the unit.
Alternative -2: Requirements for Installation with CABLE
Scan the QR Code for Configuration
and Calibration
If you experience a problem with calibration and configuration,
please scan the QR code, fill out the form with the serial ID from
the back of the unit (starts with D0 A0 11 3X XX XX), and request
configuration and calibration after completing the installation.
V-COUNT PEOPLE COUNTER
[phone]
www.v-count.com
[email protected]
Installation Steps
Step- 1: Identify the Installation Point
•Confirm the installation location before installing the unit.
•V-Count sensors are usually placed near entrance doors.
•Choose sensor locations carefully to avoid obstructions like inward-opening doors
that can affect data quality.
•Consider different installation scenarios to select the most suitable for your location.
Detailed
Installation Guide
BOOSTBI APP

For Wi-Fi Connection For Cable Connection
Attach the bracket by
rotating it to the top
of Nano.
Step-2: Installation Summary
Plug the USB-C cable
into the USB slot at the
back of Nano.
1.
2.
3.
4.
Install Nano on the
ceiling (Please refer to
the “Installation Point”
section in the first step.)
Wait for the green
light on the front of
Nano to turn on.
Place the PoE Switch on
the PoE Splitter and the
PoE Splitter on the back
of Nano. Attach the
bracket by rotating it to
the top of Nano.
Attach the bracket by
rotating it to the top
of Nano.
1.
2.
3.
4.
Install Nano on the
ceiling (Please refer to
the “Installation Point”
section in the first step.)
Wait for the green
light on the front of
Nano to turn on.
*PoE Splitter is not included in the box, it is optional
Sliding Doors
If the door(s) don't block
the sensor, position it
60 cm from the entrance,
starting from the door.
Door Opening Inside
If the door(s) might
obstruct the sensor,
position it about 60 cm
from the door's fully
open state.
Door Opening
Outside
If the door(s) don't
obstruct the sensor,
position it 60 cm
away from the door.
Alignment
Position the sensor at the
center of the entrance.
For multiple sensors,
scan the detailed guide
QR on the front page.
Step-3: Determine the Installation Direction
Please ensure the unit is installed in a top-down position where
the arrow indicates the entrance direction.
Ensure the unit is installed in a top-down position with the arrow
indicating the entrance direction (Pointing outside).
Step-4: Ethernet & Power Cabling
Nano sensor requires an internet connection to transmit traffic data to V-Count servers.
Please refer to the installation diagrams for various installation options.
Protips
Please ensure that any extension of the adaptors is
limited to the AC side, as extending the DC side may
lead to unpredictable behavior, depending on the
quality of the adaptor utilized. It is not recommended to
extend the DC side.
60 cm
60 cm
60 cm
Adaptor Data Switch
9V-36V, min 7.2W
Adaptor Option PoE Splitter Option
Nano Nano
PoE
Switch
PoE Splitter
Power Data
AC Side of the
adaptor must
be extended
Cat 5/6
Cable
5V 2A Adaptor
UPS
Modem
Nano
Technical Room
1 m 1 m
Installation
Diagram
Top-Down View