V-tech VM346 User manual

Go to www.vtechphones.com
to register your product for
enhanced warranty support
and latest VTech product news.
VM346
VM346-15
VM346-19
Quick start guide
What’s in the box VM346 baby monitor system
Baby’s room Living room
Once you power on your baby monitor, your parent unit displays image from the baby unit, and the LINK LED light
turns on. The ON/OFF LED light of the baby unit also turns on.
Status checkConnect and power on - Baby unit
> 1m (3ft)
>1m (3ft)
Connect and power on - Parent unit
CAUTION
The default volume of your parent unit
is level 4. If you experience high-pitched
screeching noise from your baby monitor
while positioning:
Make sure your baby unit and parent unit
are more than 1 meter (3 feet) apart, OR
Turn down the volume of your parent unit.
•
-
-
6U]KXOTMUT
6U]KXOTMUT
2s
63ē
63ē
< 1m (3ft)
> 1m (3ft)
>1m (3ft)
<1m (3ft)
63ē
63ē
Dim mode
With dim mode preset to on, your parent unit display will dim after 10 minutes of inactivity to conserve energy.
10 min inactivity
Press any buttons
Sound activation
Automatically turns on the parent unit screen when the baby
unit being viewed detects a sound after the screen is turned
off. When no sound is detected within 50 seconds, the
screen is automatically turned off to save power.
Sound-activated Screen
On
O
Night vision
The baby unit has infrared LEDs that allow you to
see your baby at night or in a dark room. When the
baby unit detects low light levels, the infrared LEDs
turn on automatically.The images from this baby
unit is in black and white, and appears on screen.
NOTES
It is normal if you see a shor t white gla re on your paren t
unit screen as the baby un it is adapti ng to the dark
environment.
When the i nfrared LEDs are on, t he image i s in black
and whit e. This is no rmal due t o extern al light s ources.
TIP
Depending on the surroundings and other interfering
factors, like lightings, objects, colors and backgrounds,
the display resolution may vary. Adjust the baby unit’s
angle, or place the baby unit at a higher level to prevent
glare and blurry display.
•
•
•
Install the battery
THIS SIDE UP

Specifications are subject to change without notice.
© 2016 VTech Communications, Inc. All rights reserved.
08/16. VM346_QSG_V3.Document order number : 96-011322-010-100
Basic operation - Parent unit Basic operation - Baby unit
Adjust speaker volume
Press + / VOL / -to adjust your parent unit speaker
volume. It determines the volume of sound
transmitted from your baby unit.
63ē
ē
Zoom
Press to zoom in or out.
63ē
Use the menu
Press MENU/SELECT to enter the menu, choose
a menu item, or save a setting.
While in the menu:
Press or to scroll up or down.
Press to select an item.
Press BACK to return to the main menu or
idle screen.
•
•
•
AlertTone
LowBattery Tone
NoLink Alert
Soundalert in split-view
Turn off the parent unit
Press and hold to power off your parent unit.
6U]KXOTMULL
6U]KXOTMULL
2s
Turn off the screen
Press and hold LCD ON/OFF to switch off
the screen. You can still hear sound from the
selected baby unit.
Talk to your baby unit
Press and hold TALK and speak to your parent unit.
Your voice is transmitted to the baby unit.
63ē
Long press
63ē
63℉
> More than 1
meter (3 feet)
63℉
Overview - Parent unit
Stand Power jack
Speaker
On/off
TALK
Zoom
Antenna
Microphone
Light indicators
Arrow keys
MENU / SELECT
+ / VOL / -
VIEW / LCD ON/OFF
PATROL
SPLIT
10s
Insert the screws into the
holes and tighten the screws
until only 1/4 inch of the
screws are exposed.
If you drill the holes into a stud,
go to step 3.
-OR-
If you drill the holes into an object
other than a stud, insert the wall
anchors into the holes. Tap gently
on the ends with a hammer until
the wall anchors are flush with
the wall.
Mount the baby monitor (optional)
OR
Place the wall mount bracket on a
wall and then use a pencil to mark
the top and the bottom holes as
shown. Remove the wall mount
bracket and drill two holes in the
wall (7/32 inch drill bit).
NOTES
Check for reception strength and
camera angle before drilling the holes.
•
Align the wall mount bracket and
screws with the holes in the wall
as shown. Tighten the screw in the
middle hole first, so that the wall
mount bracket position is fixed.You
can tighten the other screw in the
top hole.
Place the baby unit on the wall
mount bracket.Tighten the screw
into the threaded socket at the
bottom to secure the baby unit.
The default angle of the wall mount bracket is 90 degrees. You
can maximize your baby unit’s viewing angles by tilting the wall
mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise
direction. This will loosen the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle.
Then, rotate the knob in clockwise direction to tighten the joint
and secure the angle.
Place the baby unit on the wall mount
bracket.Tighten the screw into the threaded
socket at the bottom to secure the baby
unit. Align the holes on the wall mount
bracket with the screws on the wall, and
slide the wall mount bracket down until it
locks into place.
Change different views
(require additional baby units - VM306/VM306-15/VM306-19)
You can view from different baby units if you have more than one baby units in your system
(VM306/VM306-15/VM306-19, purchased separately).
Press VIEW to switch between the images of the baby units.
Press PATROL to alternately view the image from the baby units every 10 seconds.
Press SPLIT to view the images from all baby units at once.
Press VIEW
Overview - Baby unit
Infrared LEDs
Light sensor
Camera
ON/OFF light
/ VOL /
Play/Stop
Microphone
Skip
Temperature
sensor
Speaker
ON/OFF slide
Adjust speaker volume
Press / VOL / to adjust your baby unit speaker
volume. It determines the lullaby volume and
talkback volume transmitted from your parent unit.
Turn off the baby unit
Slide the ON/OFF switch to OFF to power off
your baby unit.
Lullaby
Press / to play lullaby on the baby unit.
Press to skip to the other lullabies.
Press / again to stop the lullaby.
•
•
LCDis turning off...
2s