V-tech Go! Go! Smart Wheels Lift &Fix Repair Shop User manual

© 2015 VTech
Printed in China
91-003036-000
User’s Manual
Lift & Fix Repair Shop™

2
SMARTPOINT®
HOT ROD
GARAGE
TWO ACCESSORY
PIECES
CAR
WASH
5 SMARTPOINT®
LOCATIONS
INTRODUCTION
Thank you for purchasing the VTech®Go! Go! Smart Wheels®Lift &
Fix Repair Shop™ learning toy!
Lift, fix and learn with the Go! Go! Smart Wheels®Lift & Fix Repair
Shop™.This interactive repair shop features two floors of pretend play.
The hot rod also responds to five SmartPoint®locations on the playset.
INTRODUCTION
REPAIR LIFT
REPAIR
GEAR

33
INCLUDED IN THIS PACKAGE
INCLUDED IN THIS PACKAGE
One SmartPoint®
base
One SmartPoint®
hot rod
One SmartPoint
®
repair lift
One SmartPoint
®
fuel station
One top wall
One fuel station
accessory piece
One wrench
storage piece
One SmartPoint
®
paint station
One bottom wall
One tire accessory One wrench
accessory
One paint station
accessory piece

4
INCLUDED IN THIS PACKAGE
One user’s manual
One label sheet
One door support
One straight
ramp track
One H-shape
support
Two spiral supports One straight support One left repair lift
support
One right repair lift
support
One car wash
track piece

5
GETTING STARTED
BATTERY INSTALLATION – HOT ROD
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the bottom
of the hot rod. Use a screwdriver to
loosen the screw.
3. Install 2 new “AAA” (AM-4/LR03)
batteries following the diagram inside
the battery box. (The use of new
alkaline batteries is recommended for
maximum performance.)
4. Replace the battery cover and tighten
the screw to secure the battery cover.
GETTING STARTED
WARNING:
All packing materials, such as tape, plastic sheets, packaging
locks and tags are not part of this toy, and should be discarded
for your child’s safety.
ATTENTION:
Pour la sécurité de votre enfant, débarrassez-vous de tous
les produits d’emballage tels que rubans adhésifs, feuilles de
plastique, attaches et étiquettes. Ils ne font pas partie du jouet.
NOTE:
Please keep this user’s manual as it contains important
information.
Unlock the packaging locks:
Turn the packaging lock counter-clockwise
several times.
Pull out and discard the packaging lock.

6
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable (Ni-Cd, Ni-MH), or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.
BATTERY NOTICE

7
LABEL INSTRUCTIONS
Please adhere the labels to the playset
securely as indicated on the following
page:
1
45
6
8
910
7
25

8
Car Wash
Car Wash
5
1
4
3
LABEL INSTRUCTIONS
2
7
10
8
9
6
1
0
G
A
L
DOWNDOWN
UPUP

9
ASSEMBLY INSTRUCTIONS
With the VTech® Go! Go! Smart Wheels®Lift & Fix Repair Shop™,
safety comes first. To ensure your child’s safety, adult assembly is
required.
1. Insert the bottom wall into the SmartPoint®base. Then, insert the
two spiral supports into the SmartPoint®base as shown below.
2. Insert the straight support into the SmartPoint®base as shown
below.
ASSEMBLY INSTRUCTIONS

10
3. Insert the left repair lift support into the SmartPoint®base. Then,
insert the right repair lift support into the SmartPoint®base as
shown below.
4. Insert the door support into the SmartPoint®base as shown.
5. Insert the SmartPoint®repair lift into the four open slots as shown
below.
ASSEMBLY INSTRUCTIONS

11
6. Insert the H-shape support into the SmartPoint®base as shown
below.
7. Insert the paint station accessory piece into the SmartPoint®paint
station as shown below. You will hear a “click” sound to indicate
the paint station accessory piece is secure. Then, attach the
SmartPoint®paint station to the supports as shown below. Press
down firmly to make sure the SmartPoint®paint station is secure.
8. Insert the fuel station accessory piece into the SmartPoint®fuel
station as shown below. Press down firmly to make sure the fuel
station accessory is secure. Then, attach the SmartPoint®fuel
station to the supports as shown below. Press down firmly to make
sure the SmartPoint®fuel station is secure.
ASSEMBLY INSTRUCTIONS

12
9. Insert the top wall into the open slots as shown below.
10. Attach the wrench storage piece to the car wash track piece.Then,
attach the car wash track piece to the bottom of the SmartPoint®
base as shown below.
11. Attach the straight ramp track to the SmartPoint®fuel station as
shown below.
ASSEMBLY INSTRUCTIONS

13
ExPAND & ExPLORE
Connect to the Go! Go! Smart Wheels
®
Deluxe Track Set
(as shown below) or other Go! Go! Smart Wheels®and Go! Go!
Smart Animals®playsets (each sold separately) to expand the Lift &
Fix Repair ShopTM and inspire creativity.
PRODUCT FEATURES – HOT ROD
1. ON/OFF SWITCH
To turn the unit ON, slide the ON/OFF
SWITCH to the ON ( ) position. To
turn the unit OFF, slide the ON/OFF
SWITCH to the OFF ( ) position.
2. AUTOMATIC SHUT-OFF
To preserve battery life, the hot rod included with the VTech®Go!
Go! Smart Wheels®Lift & Fix Repair Shop™will automatically
power-down after approximately 65 seconds without input. The
unit can be turned on again by pressing the light-up driver button,
pushingthehotrodquicklyortriggeringaSmartPoint®location.
Note: This product is in try-me mode in the packaging. After opening
the package, turn the vehicle off and on again to proceed with
normal play.
PRODUCT FEATURES - HOT ROD

14
ACTIVITIES – HOT ROD
1. Slide the ON/OFF SWITCH to the ON
position to turn the unit ON. You will
hear a song, a phrase and sounds.
The light will flash with the sounds.
2. Press the light-up driver button to
hear hot rod sounds, songs and
phrases. The light will flash with the
sounds.
3. Push the hot rod to hear fun sounds,
and melodies. While a melody is
playing, push the vehicle again to
add in fun sounds on top of the
melody. The light will flash with the
sounds.
4. For added fun, the hot rod interacts with the Go! Go! Smart
Wheels®Lift & Fix Repair Shop™. Simply roll or place the hot
rod on one of the playset’s SmartPoint®locations to hear the hot
rod play fun sounds, short tunes and phrases. The hot rod even
interacts with other Go! Go! Smart Wheels®and Go! Go! Smart
Animals®playsets (each sold separately).
ACTIVITIES – HOT ROD

15
ACTIVITIES - REPAIR SHOP
1. Put the included hot rod or any
other Go! Go! Smart Wheels®
SmartPoint®vehicle (each sold
separately) on one of the five
SmartPoint®locations to hear
fun phrases, sounds and music.
(SmartPoint®vehicles only. Other
vehicles sold separately.).
2. Move the hot rod into the CAR
WASH, and pretend to get the hot
rod sparkly clean.
3. Pull up to the SmartPoint® REPAIR
LIFT, and raise the lift to the second
floor. Then, place one of the two
included accessory pieces on the
repair gear and turn it to simulate
repairing the hot rod.
4. Place the SmartPoint®hot rod in the
PAINT AREA, and move the paint
gun back-and-forth for role-play fun.
ACTIVITIES – REPAIR SHOP

16
PRODUCT FEATURES - REPAIR SHOP
5. Go to the FUELING AREA, and
move the nozzle up and down for
role-play fun. Once fueled up, race
down the ramp in the freshly tuned
up hot rod.
6. Open the garage door and park the
SmartPoint®hot rod inside for some
rest.
CARE & MAINTENANCE
1. Keep the unit clean by wiping it with a slightly damp cloth.
2.
Keep the unit out of direct sunlight and away from any direct heat
source.
3. Remove the batteries when the unit will not be in use for an extended
period of time.
4. Do not drop the unit on hard surfaces and do not expose the unit
to moisture or water.
TROUBLESHOOTING
If for some reason the program/activity stops working or malfunctions,
pleasefollowthesesteps:
1. Please turn the unit OFF.
2. Interrupt the power supply by removing the batteries.

17
TROUBLESHOOTING / OTHER INFO
3. Let the unit sit for a few minutes, then replace the batteries.
4. Turn the unit ON. The unit should now be ready to play again.
5. If the product still does not work, replace with an entire set of new
batteries.
If the problem persists, please call our Consumer Services Department
at 1-800-521-2010 in the U.S. or 1-877-352-8697 in Canada, and a
service representative will be happy to help you.
For information on this product’s warranty, please call VTech®at
1-800-521-2010 in the U.S. or 1-877-352-8697 in Canada.
IMPORTANT NOTE:
Creating and developing Infant Learning products is accompanied
by a responsibility that we at VTech®take very seriously. We make
every effort to ensure the accuracy of the information, which forms
the value of our products. However, errors sometimes can occur.
It is important for you to know that we stand behind our products
and encourage you to call our Consumer Services Department at
1-800-521-2010 in the U.S. or 1-877-352-8697 in Canada, with
any problems and/or suggestions that you might have. A service
representative will be happy to help you.
Note:
Thisequipmenthasbeentestedandfoundtocomplywiththelimits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates,uses andcan radiateradiofrequencyenergyand,if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If

18
OTHER INFO
thisequipmentdoescauseharmfulinterferencetoradioortelevision
reception,whichcanbedeterminedbyturningtheequipmentoffand
on, the user is encouraged to try to correct the interference by one or
moreofthefollowingmeasures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthat
to which the receiver is connected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
Caution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operatetheequipment.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATIONISSUBJECTTOTHEFOLLOWINGTWOCONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
CAN ICES-3 (B)/NMB-3(B)