VADDIO TrackVIEW User manual

Camera and Electronic Products for Integrators
Ⓒ2007 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing
subject to change. TrackVIEW, Quick-Connect, StepVIEW, AutoVIEW, EZCamera and PowerRite are registered trademarks of Vaddio LLC.
All other trademarks are property of their respective owners. Form Number 341-337 Rev. E
Installation and User Guide
T
TR RA AC CK KV VI IE EW W™ ™(Patent Pending)
Automated Camera Tracking and Preset Control System
OVERVIEW:
The Vaddio™ TrackVIEW™ camera control system was designed to provide system integrators with an easy to
operate, fully featured and ultra flexible, multiple-mode camera tracking system. The TrackVIEW is a presenter
control system that incorporates both motion based camera tracking and camera preset tracking in one system
and has many unique features that enhance the automatic aspects of presenter actuated control systems.
KEY FEATURES:
•Motion Tracking or Preset Tracking or Both
The system uses motion-tracking technology with Vaddio’s preset camera control technology. This
combination of technologies when on, allows the presenter to stay on camera as they walk between preset
camera shots which are triggered by mats or IR sensors. Motion tracking can be disabled providing for only
triggered preset tracking and preset tracking can be disabled allowing for only motion tracking.
•First Step, Last Step and Multi-Step Modes
When using the TrackVIEW in Preset Tracking mode, the unit can be set-up to respond to the first trigger
using the AutoVIEW™ IR or StepVIEW™, the last trigger or a combination of triggers. The multi-step mode
is commonly used with multiple presenters where two triggers can be programmed into a wide shot to pick
up a larger area.
•Two Camera System
The TrackVIEW was designed to use Sony® PTZ cameras. For the Sony systems, TrackVIEW 100, 70 and
HD1, the Sony EVI-D70 is used for the reference camera and the tracking camera is the Sony EVI-D100,
EVI-D70 and EVI-HD1 respectively. The Reference camera is adjusted to a wide-angle shot to see the
whole presentation area and the Tracking Camera looks at a smaller area and pans back and forth to follow
the movement recognized by the Reference Camera. Both cameras are equipped with the Vaddio
EZCamera™ cabling system for Cat. 5 connectivity.
•Programming and Presets
The system has five single preset triggers that can be any combination of up to five AutoVIEW IR sensors or
StepVIEW presence sensing mats. In addition, up to ten more multi-step presets can be programmed for
wider shots when multiple presenters are working together.
Figure 1:
TrackVIEW Controller

TrackVIEW Install Guide 341-337 Rev. E
Page 2 of 32
TrackVIEW and Peripherals Install Guide
•IR Remote Controller
The system employs a multi-function IR remote controller for preset programming and camera control.
•Built-in EZCamera Cabling System Quick-Connect™ Box
When using the TrackVIEW 100 and 70 the reference and tracking camera inputs have built-in Quick-
Connect boxes for running power and video over a single Cat. 5 cable. When using the EVI-HD1 as the
Tracking camera, the external Quick-Connect PRO and EZIM are required.
•PowerRite™ Power Supply
The TrackVIEW internal PowerRite power supply is sized to power the five triggers (AutoVIEW IR and
StepVIEW triggers) and two PTZ cameras in the TrackVIEW 100 and 70 systems. The inputs also have a
15V/18V power selection switch for Cat. 5 power/video cables to match the cameras power requirements as
the cable distance to the camera increases (see Table 1 on pg. 9). If the EVI-HD1 is used as the tracking
camera, the Quick-Connect PRO and EZIM are powered by an external PowerRite 36VDC power supply.
•USB and DB-9 Connection for System Set-up and Software
The system set-up port is on a USB connection to eliminate the need for the installer to find a laptop with a
DB-9 RS-232 port. The system software is intuitive and easy to use to maximize system performance and
provide for quick set-ups. (Note: USB overrides serial port. The serial port is disabled when using USB)
INTENDED USE:
Before operating the TrackVIEW system, please read the entire manual thoroughly. The system was designed,
built and tested for use indoors with the provided power supply. The use of a power supply other than the one
provided or outdoor operation has not been tested and could damage the electronics and/or create a potentially
unsafe operating condition.
SAVE THESE INSTRUCTIONS:
The information contained in this manual will help you install and operate your Vaddio TrackVIEW. If these
instructions are misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most
pertinent product drawings for the Vaddio product line on the website. These documents can be downloaded
from www.vaddio.com free of charge.
IMPORTANT SAFEGUARDS:
Read and understand all instructions before using. Do not operate the system if it has been dropped or
damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the risk of
electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.
Use only the power supply provided with the TrackVIEW system. Use of any
unauthorized power supply will void any and all warranties.

TrackVIEW Install Guide 341-337 Rev. E
Page 3 of 32
TrackVIEW and Peripherals Install Guide
UNPACKING:
Carefully remove the products and all of the parts from the packaging. The TrackVIEW is sold in five (5)
different configurations:
TrackVIEW 100
TrackVIEW System with both Tracking and Reference Cameras for Smaller Rooms - Part # 999-7000-100
•One (1) – Vaddio TrackVIEW Controller, IR Remote, Power Supply, Rack Ears and System Set-up Software
•One (1) – Sony EVI-D70 PTZCam with EZCamera Shoe and Wide-angle Lens (reference camera)
•One (1) – Sony EVI-D100 PTZCam (10X optical zoom) with EZCamera Shoe & Vaddio IR Remote
Commander (tracking camera)
•One (1) – Vaddio Dual Camera Mount for Model 70 and Model 100 (70/100 configuration)
•USB Cable
TrackVIEW 70
TrackVIEW Kit with both Tracking and Reference Cameras (two EVI-D70s) - Part # 999-7000-070
•One (1) – Vaddio TrackVIEW Controller, IR Remote, Power Supply, Rack Ears and System Set-up Software
•One (1) – Sony EVI-D70 PTZCam with EZCamera Shoe and Wide-angle Lens (reference camera)
•One (1) – Sony EVI-D70 (18X optical zoom) PTZCam with EZCamera Shoe & Vaddio IR Remote
Commander (tracking camera)
•One (1) – Vaddio Dual Camera Mount for Dual Model 70 (70/70 configuration)
•USB Cable
TrackVIEW HD1
TrackVIEW Kit with EVI-HD1 Tracking Camera and EVI-D70 Reference Camera - Part # 999-7000-630
•One (1) – Vaddio TrackVIEW Controller, IR Remote, Power Supply, Rack Ears and System Set-up Software
•One (1) – SonyEVI-D70 PTZCam with EZCamera Shoe and Wide-angle Lens (reference camera)
•One (1) – Sony EVI-HD1 PTZCam (12X optical zoom) with Quick-Connect PRO and EZIM (EZCamera
Interface Module), IR Remote Control, 36VDC Power Supply, (tracking camera)
•Two (2) – Vaddio Camera Mounts (EVI-HD1 and EVI-D70)
•USB Cable

TrackVIEW Install Guide 341-337 Rev. E
Page 4 of 32
TrackVIEW and Peripherals Install Guide
TrackVIEW Front Panel Controls
1) System Power Switch (system on/off)
2) First Step Priority
a. For use with AutoVIEW IR or StepVIEW Triggers. First Step Priority mode gives the first
trigger-activated priority over any subsequent triggers. The subsequent triggers are ignored.
3) Last Step Priority
a. For use with AutoVIEW IR or StepVIEW Triggers. Last Step Priority mode gives the last trigger-
activated priority over any other triggers already activated. The last trigger activated has
priority.
4) Multi-Step Priority
a. For use with AutoVIEW IR or StepVIEW Triggers. Multi-Step Priority allows two different
triggers to define a unique and separate camera position preset when both triggers are
activated simultaneously.
5) IR Window
a. IR window for use with Vaddio TrackVIEW IR Remote controller.
6) Tracking Disable
a. Turns on/off (on/off toggle) camera tracking.
7) Preset Disable
a. Turns on/off (on/off toggle) camera presets triggered by StepVIEW Mats or AutoVIEW IR
sensors
b. Presets cannot be programmed when Preset Disable button is on (active).
8) Program Mode
a. Enters program mode to set up camera’s preset shot and store the preset from the front panel
or IR remote control.
9) Tracking Camera Preset
a. Default camera position upon start-up. Programs tilt and zoom position for tracking camera
(pan position for the Tracking Camera is dynamically calculated from reference camera motion
detection).
10) Presets for Camera Positioning
a. There are five (5) discrete camera presets that can be programmed into the TrackVIEW.
11) Rack Mount Ears
a. Rack mount ears are included with the TrackVIEW.
1
2
3
4
5
6
9
8
10
11
7
Figure 2:
TrackVIEW Controller
Front Panel

TrackVIEW Install Guide 341-337 Rev. E
Page 5 of 32
TrackVIEW and Peripherals Install Guide
TrackVIEW Back Panel I/O and Controls
1) Power Input
a. Note: Use only the 18VDC Power Supply Provided with the TrackVIEW.
Tracking Camera Section
2) 15V/18V Power Switch
a. EZCamera Cat. 5 cabling runs for Video/Power have a 15V/18V power selection switch for Cat.
5 power/video cables to match the cameras power requirements as the cable distance to the
camera increases (15V for shorter Cat. 5 runs, 18V for longer runs - see Table 1, pg. 9).
b. For EZCamera Cat. 5 cabling runs for when using the EVI-HD1 as a tracking camera, an
external power supply is used (cabling distances are up to 500 feet for video and power).
3) Video/Power Jack
a. RJ-45 jack to carry power to the Tracking Camera and receive video from the camera over a
Cat. 5 cable.
4) Control Jack
a. RJ-45 jack to carry RS-232 to the Tracking Camera.
5) S-Video Input Jack
a. S-Video Input jack is for the S-Video output of the EVI-HD1 Quick-Connect PRO for the
TrackVIEW HD1 System.
6) S-Video Output Jack
a. S-Video output to view system/monitor for Tracking Camera.
7) Composite Video Output (BNC)
a. Composite output to view system/monitor for Tracking Camera.
Reference Camera Section
8) 15V/18V Power Switch
a. 15V/18V power selection switch for Cat. 5 power/video cables to match the reference cameras
power requirements as the cable distance to the camera increases (see Table 1, pg. 9).
b. Wide Angle Lens is provided for the EVI-D70 Reference Camera (lens is included but may not
be required depending on distance to, and width of, the presentation area).
9) Video/Power Jack
a. RJ-45 jack to carry power to the Reference Camera and receive Video from the camera over
Cat. 5 cable.
10) Control Jack
a. RJ-45 jack to carry RS-232 to the Reference Camera.
11) S-Video Output Jack
a. S-Video output to set-up monitor for Reference Camera.
12) Composite Video Output (BNC)
a. Composite output to set-up monitor for Reference Camera.
1
11
2
3
5
6
7
9
8
4
10
12
15
14
13
17
16
Figure 3:
TrackVIEW Controller
Rear Panel

TrackVIEW Install Guide 341-337 Rev. E
Page 6 of 32
TrackVIEW and Peripherals Install Guide
13) USB Connection
a. For Laptop access to System Set-up Software without a serial port requirement on the Laptop.
(Note: USB overrides serial port. The serial port is disabled when using USB)
Preset Triggers Section
14) AutoVIEW IR Sensor input Jacks
a. Five (5) RJ-45 jacks for AutoVIEW IR Sensors. Cat. 5 cabling supplies power to the IR Sensor
and the sensor activates when a presenter’s presence is detected within the tuned area of the
IR Sensor.
15) StepVIEW Mat Closure Inputs
a. Five (5) Phoenix type connectors for StepVIEW Mats. The StepVIEW Mats provide a closure to
the TrackVIEW when a presenter steps on the mat.
Notes on the Preset Trigger Section
The TrackVIEW will recognize a total of five (5) preset triggers maximum.
(Example: 4-mats and 1-IR sensor, or 3-IR sensors and 2-mats, any combination of up to five (5)
triggers total). Use only one input per Preset Trigger number.
16) RS-232 Control Input
a. For use with an external control system or PC to control the TrackVIEW.
17) RS-232 Aux. Control Output
a. For use with Pass Through Mode ON, passes control information between RS-232 ports
TrackVIEW IR Remote Controller
The Vaddio IR Remote Controller for the TrackVIEW controls all
the functions that are accessible through the front panel plus
allows for camera P/T/Z control for set-ups and setting trigger
presets (see Figure 4). Program the remote by installing the
batteries, Press and Hold both the POWER and TRIGGER
DISABLE 1 buttons for 5 seconds. The unit is programmed.
1. Power On/Off Control
2. Priority Control
a. First Step
b. Last Step
c. Multi-Step
3. Program Mode
4. Presets
a. Five (5) Position Presets for Tracking Camera
b. Track – Tracking Camera Preset
5. Tracking Disable and Preset Disable Controls
a. The Tracking Disable button (toggle on/off) disables the
automatic camera tracking.
b. The Preset Disable button (toggle on/off) disables the stored
presets from activating.
6. Zoom IN and OUT controls
a. For controlling Tracking camera zoom position for setting
presets or when Presets and Tracking are disabled, provides
for real-time control of Tracking camera Zoom position.
7. Pan/Tilt Controls
a. For controlling Tracking camera Pan/Tilt position for setting
presets or when Presets and Tracking are disabled, provides
for real-time control of Tracking camera Pan/Tilt position.
8. Trigger Disable
a. Allows for individual stored presets (1 through 5) to be
momentarily disabled (toggle on/off). When an individual
trigger is disabled, the front panel LED turns red.
Note: If the IR Remote arrives unprogrammed or batteries are removed,
make sure batteries are installed, then PRESS and HOLD both the
“POWER” and “TRIGGER DISABLE 1” buttons for 5 seconds. The
remote is reprogrammed.
TrackVIEW
Powe
r
Priorit
y
First
Last
Multi
Pro
g
ram
Presets
1 2
3 4
5 Track
Tracking
Disable
Preset
Disable
Zoom
In
Out
Trigger
Disable
1 2 3
4 5
1
2
3
5
8
4
6
7
Figure 4:
TrackVIEW IR Remote Controller

TrackVIEW Install Guide 341-337 Rev. E
Page 7 of 32
TrackVIEW and Peripherals Install Guide
INSTALLING THE CAMERAS
The TrackVIEW Base System includes only the reference camera and wide-angle lens. The reference camera
can be one of the following cameras provided the cabling is correct (see Appendix A – system pin-outs):
•Sony EVI-D100
•Sony EVI-D70
•Sony EVI-HD1
No other unitized pan/tilt/zoom cameras will operate with the TrackVIEW.
The TrackVIEW 70 System
The TrackVIEW 70 system includes the Vaddio Dual Camera Thin Line Wall Mount that mounts the cameras in
a vertical array to minimize the space between the cameras and make mounting the cameras very fast and easy
(see Figure 5). The dual camera wall mount will fit all the TrackVIEW 70 and TrackVIEW 100 dual camera kits
(see Figure 6). Both cameras use the EZCamera cabling shoe and are powered from the TrackVIEW controller.
Figure 5:
EVI-D70 Reference camera and Tracking
Camera (Platinum white only) with Dual
Thin Line Wall Mount and EZCamera
cabling shoes and wide angle lens on top
camera (reference camera).
The reference camera can be mounted
on top (as shown). The performance of
the system is enhanced by the vertical
position.
A slot in the back of the top shelf allows
for cabling management and the slots in
the top will accommodate both the EVI-
D70 or EVI-D100 PTZ cameras.
Note: Use only the ¼”-20 camera mounting
screws provided, using longer camera mounting
screws will damage the camera an void the
warranty.
Figure 6:
Dual Thin Line Wall Mount
fits EVI-D70 and EVI-D100
Cameras with EZCamera
cabling shoes.
The dual mount is shipped
platinum white only and
mounts to a 2-gang wall
box or with wall anchors.

TrackVIEW Install Guide 341-337 Rev. E
Page 8 of 32
TrackVIEW and Peripherals Install Guide
TrackVIEW 100 System
The TrackVIEW 100 System uses the EVI-D70 with a wide-angle lens for the reference camera and an EVI-
D100 camera for the Tracking Camera. The EVI-D100 has a 10X optical zoom lens and will work well for small
room environments. Both cameras use the EZCamera cabling shoe and are powered from the TrackVIEW
controller. The EVI-D100 is to be mounted on the top shelf where the slot in the mount can accommodate the
¼”-20 mounting threads of the EVI-D100 or the EVI-D70.
TrackVIEW HD-1 System
The TrackVIEW HD1 System uses the EVI-D70 with a wide-angle lens for the reference camera and the EVI-
HD1 camera for the Tracking Camera. The EVI-HD1 has a 12X optical zoom lens and will work well for any
environment that demands the quality of a HD imaging device. Both cameras use the EZCamera cabling shoe
and only the Reference EVI-D70 is powered from the TrackVIEW controller. The EVI-HD1 must use the Quick-
Connect PRO, EZIM and the supplied PowerRite power supply as the HD1 camera draws a significant amount
of power when panning and tilting.
Figure 7:
Cameras and mount for the TrackVIEW 100 are pictured below; EVI-D70 (left), the EVI-D100 in platinum gray only
(center) and the dual thin line wall mount (right) fits on a standard 2-gang wall box or mounts with wall anchors.
Note: Use only the ¼”-20 camera mounting screws provided, using longer camera mounting screws will damage the camera an void the warranty.
Figure 8:
Cameras and mount for the TrackVIEW HD1 are pictured below; EVI-D70 (left), the EVI-HD1 with mounts.

TrackVIEW Install Guide 341-337 Rev. E
Page 9 of 32
TrackVIEW and Peripherals Install Guide
Connecting the TrackVIEW Cameras to the TrackVIEW Controller
The TrackVIEW 70 and 100 Cameras are connected to the TrackVIEW Controller with Cat. 5 cables for video,
power and control. Video and power share one Cat. 5 and control occupies the 2nd Cat. 5. For setting the
15V/18V switch and maximum cabling distances for the Video/Power Cat. 5 cable, please see Table 1. Cable
the Cat. 5 cables between the TrackVIEW Controller and the Cameras with the EZCamera cabling shoes.
Connect the main video output to the main video monitor and the reference video out to the reference monitor
(the reference monitor may be temporary after the system has been set-up and tuned. There are S-Video and
composite outputs available and for each output and both outputs are concurrently active.
Table 1:
EZCamera Cabling Information – Voltage settings and Maximum Cat. 5 cable lengths for Video/Power
Vaddio Camera System Power Settings Cat. 5 Cabling Distances*
EVI-D70 with EZCamera Shoe 15V Switch Position
18V Switch Position
Up to 100’ / 30.48m
From 100’ to 200’ / 61m Maximum
EVI-D100 with EZCamera Shoe 15V Switch Position
18V Switch Position
Up to 75’ / 22.86m
From 75’ to 125’ / 38.1m Maximum
EVI-HD1
Has discrete PowerRite
Power Supply and Quick-
Connect Box
Up to 500’ / 154m Maximum for HD1 only
Figure 9:
TrackVIEW 70 System (two EVI-D70) with cameras
connected to the TrackVIEW Controller with Cat. 5
cables (the 1st for video/power and the 2nd for control).
For Video/Power cabling lengths please see Table 1.
Main and Reference monitors are connected with
standard S-Video or composite video cables.
Cat. 5 for
Video/Power
Cat. 5 for
Video/Power
Cat. 5 for
Control
Cat. 5 for
Control
Main
Monitor
Reference
Monitor
TrackVIEW Controller – Rear Panel
EVI-D70
with Shoe
EVI-D70
with Shoe
S-Video S-Video

TrackVIEW Install Guide 341-337 Rev. E
Page 10 of 32
TrackVIEW and Peripherals Install Guide
TrackVIEW HD1 System Connections
The TrackVIEW HD1 tracking camera is not connected the same way as the other TrackVIEW Systems. The
reference camera is connected to the TrackVIEW Controller with Cat. 5 cables for video/power and control.
Video and power share one Cat. 5 and control occupies the 2nd Cat. 5. For setting the 15V/18V switch for the
reference camera and maximum cabling distances for the Video/Power Cat. 5 cable (see Table 1). The EVI-
HD1 does not draw power from the TrackVIEW controller. It is supplied power from its own Quick-Connect
PRO, EZIM and 36VDC power supply (see Figure 10). The EVI-HD1 uses Cat. 5 cables for Video and Power
(2) from the Quick-Connect PRO and a 3rd Cat. 5 for Control. Connect the main video output, SD or HD, to the
main video monitor or codec and the reference video out to the reference monitor.
Figure 10:
TrackVIEW HD1 System with cameras connected to the TrackVIEW Controller with Cat.
5 cables. Main and Reference monitors are connected with standard S-Video or
composite video cables.
Cat. 5 for
Video/Power
Cat. 5 for
Control
Cat. 5 for Control
Main
Monitor
Reference
Monitor
TrackVIEW Controller – Rear Panel
EVI-D70
with Shoe
S-Video S-Video
S-Video
36VDC
Power
Supply
To HD Monitor/Codec
Quick Connect PRO
Video
(HD or SD)
Power
Note: See WallVIEW HD1 Operation Manual
for Installation Assistance