Valcom VIP-148AL User manual

1 947810
CAUTION: To reduce the risk of electric shock,
Do not remove cover.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates that dangerous
voltage constituting a risk of electric
shock is present within this unit.
This symbol indicates thatthere are
important operating and maintenance
instructions in the literature accompanying
this unit.
Issue 1
VIP-148AL IP Talkback Horn
INTRODUCTION
The VIP-148AL IP Talkback Horn enables
two-way handsfree voice access to a single
location over an IP-based network. This allows a
page zone extension anywhere on the network.
The horn audio level is electronically adjusted via
software. A call switch input connection is
provided for call initiation. Power is provided to
the VIP-148AL via a Power over Ethernet (PoE)
switch meeting the 802.3af specification.
SPECIFICATIONS
Access Methods
PBX, FXO Port w/VIP-811
POTS telephone set w/VIP-811
FXS Port w/VIP-821
SIP telephone system
Features
RJ-45 for network connection
Network activity LEDs
Power over Ethernet (PoE) 802.3af
compatible
Dimensions/Weight VIP-148AL
Horn
7.38” H x 10.0” W x 10.4” D
(18.75cm x 25.4cm x 26.42cm)
Weight: 3.70 lbs. (1.68 kg)
Network Interface
1.62” H x 5.63” W x 3.45” D
(4.11 cm) x (14.30 cm) x (8.73 cm)
with brackets – 8.22” W (20.87 cm)
Weight: 2.10 lbs. (0.95 kg)
Environment
Network Interface:
Temperature: 0 to +40° C
Humidity: 0 to 85% non-precipitating
Horn:
Suitable for indoor or outdoor installation
Nominal Power Requirements
Via 802.3af (PoE) Ethernet Switch: Class 3
Packing List
Qty Item
1 Network Interface
1 VIP-148AL Horn
1 VSP Document
1 “C” Clamp
1 VM-186 RJ-45 Connector
Precautionary Designations

2 947810
FCC Information
This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated
in a commercial environment. This
equipment generates, uses and can radiate
radio frequency energy and if not installed
and used in accordance with the instruction
manual, may cause harmful interference to
radio communications. Operation of this
equipment in a residential area may cause
harmful interference in which case the user
will be required to correct the interference at
his own expense.
INSTALLATION
Operation:
Provides talkback intercom via Network
connection to customer telephone system or
stand alone telephone set. Interface to customer
telephone system can be via SIP registration,
FXO port or FXS port (additional equipment
required in all cases). The optional call button
may be programmed to initiate a call to one of the
above telephone system interfaces. When the
call is answered, a hands-free communications
path is established to the horn.
Mounting (Network Interface)
The VIP-148AL Network Interface is designed for
wall or table mounting and must be within 100
meters of the network switch.
Mounting (Horn)
The VIP-148AL Horn is designed for most FD
electrical box or wall mounting and must be within
300 meters of the VIP-148AL Network Interface.
See NEMA OS 3-2002 sec.1.2.3.5 for FD box
specifications.
Attaching Speaker to Base
NOTE: For ease of installation, the base can be
attached to the speaker before or after the base
is mounted.
Loosen position adjustment knob
Insert the ball of the base into the socket of
the speaker
Tighten the position adjustment knob
These horns should be mounted 15 to 20 feet
above the floor to allow for best sound
distribution. The units can be mounted to a wall,
a beam or an electrical box.
A “C” clamp is provided with the horns to
allow mounting to a beam. When using the
“C” clamp for mounting, remove the signal
cable from the ball mount. Reinstall an RJ45
connector on the signal cable after mounting,
using the T568B pinout scheme. See Figure
1.
The base has holes punched for a
double-gang square box, but by punching out
additional knockout holes, the base can be
mounted to a single-gang or octagon box
See Figure 2.
Mount the base to wall studs using the two
holes provided. Knockout holes are provided
for punch out should additional holes be
desired. See Figure 3.
The horns may be rotated or moved up and down
to obtain the desired position by loosening the
position adjustment knob at the bottom of the unit
approximately one turn. Make required
adjustments, retighten knob.
Figure 1. Mounting to a Beam with a “C” Clamp

3 947810
Figure 2. Mounting to an Electrical Backbox
Figure 3. Mounting to Wall stud
Power Connections
The only method of powering a VIP-148AL
Network Interface is via a Power over Ethernet
(PoE) switch or power injector meeting the
802.3af specification. Make all required signal
connections before connecting to Ethernet switch
or power injector meeting the 802.3af
specification.
Network Connection
The VIP-148AL Network Interface has one RJ-45
Ethernet network connector and one RJ-45 horn
connector.
Use a standard Ethernet patch cable to connect
the VIP-148AL to an Ethernet switch.
Signal Connections
Audio output connection is made from the Signal
Output. The RJ-45 connector on the horn is
connected directly to the RJ-45 Signal Output
socket on the Network Interface. If additional
length is required, any standard T568B extension
may be used. See Figure 4.
If desired, a normally-open call button may be
connected to the Blue, White/Blue pair of the
horn RJ-45 connector.
The VM-186 RJ-45 connector provides easy
access to these connections.
Status Indicator Lights
The VIP-148AL has 2 status indication lights
located on network jack:
Green LED: (Link) Indicates Ethernet
connection when illuminated.
Yellow LED: (Activity) Indicator flashes to
indicate network activity.
Setup
Information specific to your application will need
to be programmed into the VIP-148AL using a
computer. The PC used for programming should
be connected to the same subnet as the
VIP-148AL. Setup will be done using the IP
Solutions Setup Tool. The IP Solutions Setup
Tool is available for download on the Valcom
website at www.valcom.com/vipsetuptool.

4 947810
TECHNICAL ASSISTANCE
Assistance in troubleshooting is available from
the factory when problems are encountered.
Call [phone] and press 1 for Technical
Support or visit our website at
http://www.valcom.com.
Valcom equipment is not field repairable.
Valcom, Inc. maintains service facilities in
Roanoke, VA. Should repairs be necessary,
attach a tag to the unit clearly stating your
company name, address, phone number, contact
person and the nature of the problem. Send the
unit to:
Valcom, Inc.
Repair & Return Dept.
5614 Hollins Road
Roanoke, Va. 24019-5056
VALCOM LIMITED WARRANTY
Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under conditions of
normal use and service for a period of one year from the date of shipment. This Limited Warranty obligation shall be limited to the replacement, repair or refund
of any such defective device within the warranty period, provided that:
1. inspection by Valcom, Inc. indicates the validity of the claim;
2. the defect is not the result of damage, misuse or negligence after the original shipment;
3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (a service charge plus parts
and labor will be applied to units defaced or physically damaged);
4. freight charges for the return of products to Valcom are prepaid;
5. all units 'out of warranty' are subject to a service charge. The service charge will cover minor repairs (major repairs will be subject to
additional charges for parts and labor).
This Limited Warranty is in lieu of and excludes all other warranties, expressed or implied and in no event shall Valcom, Inc. be liable for any
anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase, operation,
maintenance, installation, removal or use of the product. The maximum liability of Valcom under this warranty is limited to the purchase price of the
specific Product covered by the warranty.
Disclaimer. Except for the Limited Warranty provided herein, the product is provided “as-is” without any warranty of any kind whatsoever including, without
limitation, any WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.
This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should be notified
immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.
Headquarters:
Valcom, Inc.
5614 Hollins Road Roanoke, VA 24019-5056
Phone: [phone] FAX: [phone]

5 947810
RJ45 NETWORK
CONNECTION
SIDE
HORN SIGNAL CONNECTION
HORN
RJ45 NETWORK
CONNECTION
SIDE
STANDARD
RJ45 PATCH CABLE
(T568B)
Typical 568B
RJ-45 Jack
RJ-45
CAT 3/5/6
VM-186
RJ45
WHITE/GREEN
GREEN
WHITE/BROWN
BROWN
BROWN
BLUE
WHITE/BLUE
BLUE
WHITE/ORANGE
ORANGE
WHITE/GREEN
GREEN
WHITE/BROWN
BROWN
WHITE/BLUE
BLUE
WHITE/ORANGE
ORANGE
HORN
*The Maximum Recommended Distance
From the IP Link to the Horn is 350’.
CALL IN SWITCH
NORMAL OPEN
MOMENTARY CLOSED
(OPTIONAL)
Figure 4. Signal Connections