VALKYRIE Syn 240 User manual

SYN
www.my-valkyrie.com
INSTALLATION GUIDE
Valkyrie Syn 240/280/360/420/480

1
AIO Water Cooling Parts
Fan
1x AIO water cooling radiator
1x Wire Kit & Hub Set
1 x with Valkyrie Syn 140
2 x with Valkyrie Syn 280
3 x with Valkyrie Syn 420
2 x with Valkyrie Syn 240
3 x with Valkyrie Syn 360
4 x with Valkyrie Syn 480
EN

2
1x Intel Backplate
2x AMD Brackets
2x Intel Brackets
Fan screw
1x Thermally conductive
silicone grease
Fan screw
(extended)
Radiator screw
4x Intel / AMD Bolts
4x LGA2011 Bolts
4x Nuts
1x TF Card
120 x 4 / 140 x 4 / 240 x 8 / 280 x 8
360 x 12 / 420 x 12 / 480 x 16
120 x 4 / 140 x 4 / 240 x 8 / 280 x 8
360 x 12 / 420 x 12 / 480 x 16
120 x 4 / 140 x 4 / 240 x 8 / 280 x 8
360 x 12 / 420 x 12 / 480 x 16
*Please check the received goods to make sure the parts are complete.
1x Nut Socket
EN

WATER
COOLING

4
Radiator Installation
Step 1: Install fan
Use the fan screws to secure the fan to the radiator.
*Please use the shorter fan screws. DO NOT use extended screws to secure the cooling fan.
Step 2: Install radiator
Use the radiator screws to secure the radiator to the case.
EN

5
Intel LGA1200/1700 Installation
We have marked the parts required for installing the Intel LGA1200/1700
platform for you.
1x Intel Backplate
2x Intel Brackets
4x Intel / AMD Bolts
1x Nut Socket
4x Nuts
Step 1: Install backplate
1. Align the backplate to the corresponding platform holes.
2. Install the backplate onto the back of the motherboard.
* You may slide it to adjust for alignment with the corresponding platform holes.
* Use the inner mounting hole position for 1200
(115X) and outer mouting hole position for 1700.
EN

6
Step 2: Install screws
Install Intel/AMD bolts to the motherboard.
*The larger end of the screw faces down.
Step 3: Install brackets
Put the brackets onto the bolts and tighten them with nuts using a nut socket.
*You can install the water block in a different direction, if you rotate the brackets to 90 degrees.
EN

7
Step 5: Install water block
Align the water block to the holes and screw it onto brackets.
Step 4: Remove the protective cover
Take off the protective cover from the coldplate.
*It is critical to the cooling performance.
EN

8
Step 6: Complete installation
Please refer to the “Wiring” for wiring.
EN

9
Intel LGA2011/2066 Installation
We have marked the parts required for installing the Intel LGA2011/2066
platform for you.
4x LGA2011 bolts 4x Nuts
Step 1: Install screws
Install Intel LGA2011 bolts to the motherboard.
2x Intel Brackets
1x Nut Socket
EN

10
Step 2: Install brackets
Put the brackets onto the bolts and tighten them with a nuts using nut socket.
*You can install the water block in a different direction, if you rotate the brackets to 90 degrees.
Step 3: Remove the protective cover
Take off the protective cover from the coldplate.
EN

11
Step 4: Install water block
Align the water block to the holes and screw it onto the brackets.
Step 5: Complete installation
Please refer to the “Wiring” for wiring.
EN

12
EN

13
AMD AM4/AM5 Installation
We have marked the parts required for installing the AMD AM4/AM5 platform
for you.
2x AMD brackets
Step 1: Prepare the motherboard
Screw out the 4 bolts. Remove the original bracket on the motherboard.
Keep the original backplate.
4x LGA2011 bolts 4x Nuts
1x Nut Socket
EN

14
Step 3: Install brackets
Put the brackets onto the bolts and tighten them with nuts using a nut socket.
Step 2: Install screws
Install Intel/AMD bolts to the motherboard.
*The larger end of the screw faces down.
EN

15
Step 4: Removing protective cover
Remove the protective cover from the coldplate.
*It is critical to the cooling performance.
Step 5: Install water block
Align the water block to the holes and screw it onto brackets.
EN

16
Step 6: Complete installation
Please refer to the “Wiring” for wiring.
EN

WIRING