VALKYRIE Dragonfang 240 User manual

DRAGONFANG
www.my-valkyrie.com
INSTALLATION GUIDE
Valkyrie Dragonfang 240/280/360/420/480

1
AIO Water Cooling Parts
Fan
1x AIO water cooling radiator
1x Wire Kit & Hub Set
1 x with Valkyrie Dragonfang 140
2 x with Valkyrie Dragonfang 280
3 x with Valkyrie Dragonfang 420
2 x with Valkyrie Dragonfang 240
3 x with Valkyrie Dragonfang 360
4 x with Valkyrie Dragonfang 480
EN

2
1x Intel Backplate
2x AMD Brackets
2x Intel Brackets
Fan screw
1x Thermally conductive
silicone grease
Fan screw
(extended)
Radiator screw
4x Intel / AMD Bolts
4x LGA2011 Bolts
4x Nuts
4x Bracket Installation Screws
2x AMD fastener
120 x 4 / 140 x 4 / 240 x 8 / 280 x 8
360 x 12 / 420 x 12 / 480 x 16
120 x 4 / 140 x 4 / 240 x 8 / 280 x 8
360 x 12 / 420 x 12 / 480 x 16
120 x 4 / 140 x 4 / 240 x 8 / 280 x 8
360 x 12 / 420 x 12 / 480 x 16
*Please check the received goods to make sure the parts are complete.
EN

WATER
COOLING

4
Radiator Installation
Step 1: Install fan
Use the fan screws to secure the fan to the radiator.
*Please use the shorter fan screws. DO NOT use extended screws to secure the cooling fan.
Step 2: Install radiator
Use the radiator screws to secure the radiator to the case.
EN

5
Intel LGA1200/1700 Installation
We have marked the parts required for installing the Intel LGA1200/1700
platform for you.
1x Intel Backplate
2x Intel Brackets
4x Intel / AMD Bolts
4x Bracket Installation Screws
4x Nuts
Step 1: Install backplate
1. Align the backplate to the corresponding platform holes.
2. Install the backplate onto the back of the motherboard.
* You may slide it to adjust for alignment with corresponding platform holes.
* Use the inner mounting hole position for 1200
(115X) and outer mouting hole position for 1700.
EN

6
Step 2: Install screws
Install Intel/AMD bolts to the motherboard.
*The larger end of the screw faces down.
Step 3: Removing
protective cover
Remove the protective
cover from coldplate.
* it is critical to the cooling
performance.
EN

7
Step 5: Install water block
Put the water block onto the studs and use nuts to x it.
Step 4: Install bracket
Use bracket bolts to install the bracket to the water block.
EN

8
Step 6: Complete installation
Please refer to the “Wiring” for wiring.
EN

9
Intel LGA2011/2066 Installation
We have marked the parts required for installing the Intel LGA2011/2066
platform for you.
4x LGA2011 bolts
4x Bracket Installation Screws
4x Nuts
Step 1: Install screws
Install Intel LGA2011 bolts to the motherboard.
2x Intel Brackets
EN

10
Step 2: Removing protective cover
Remove the protective cover from the coldplate.
*It is critical to the cooling performance.
Step 3: Install bracket
Use bracket bolts to install the bracket to the water block.
EN

11
Step 4: Install water block
Put the water block onto the studs and use nuts to x it.
Step 5: Complete installation
Please refer to the “Wiring” for wiring.
EN

12
EN

13
AMD AM4/AM5 Installation
We have marked the parts required for installing the AMD AM4/AM5 platform
for you.
2x AMD brackets
2x AMD fastener
4x Intel / AMD bolts
4x Bracket Installation Screws
4x Nuts
Step 1: Prepare the motherboard
Screw out the 4 bolts. Remove the original bracket on the motherboard. Keep
the original backplate.
EN

14
Step 3: Install brackets
Install AMD brackets onto the screws and tighten them with nuts.
Step 2: Install screws
Install Intel/AMD bolts to the motherboard.
*The larger end of the screw faces down.
EN

15
Step 4: Removing protective cover
Remove the protective cover from the coldplate.
*It is critical to the cooling performance.
Step 5: Install AMD fastener
Use bracket bolts to install the AMD fastener to the water block.
EN

16
Step 6: Install Water Block
Align bracket to the holes and tighten the spring screws on both ends.
Step 7: Complete installation
Please refer to the “Wiring” for wiring.
EN

WIRING