ABRASIVE VAC
BRUSHLESS
140
N.
Brandon
P
.O.
Box
74,
Fallbrook,
CA
92028
1-800-V
ANIMAN
(826-4626)
www.vaniman.com [email protected]ABRASIVE VAC-11/09
Page 1
PACKING LIST
1 - Abrasive Vac unit
1 - Power Cord
1 - Foot Remote (1443)
1 - 2½”x 6’ Hose with 1½” Hose End (VMC-1023B)
ASSEMBLY INSTRUCTIONS
1. Remove the unit and all additional parts from the two boxes. Check against the packing list.
2. Assemble the three foot hose with 1’/2” hose end (VMC-1023B) to the vacuum unit and the other
end to the accessory. For 2”1/2” hose connection, remove the grey hose end and use the remaining
white hose connector.
3. Plug the removable power cord into the socket on the top of the SandVac then plug the other end
into a standard 110 Volt wall socket. Connect the black remote switch tube to the black remote
switch connector on the unit; test by turning the power switch on or by pressing the remote switch.
MAINTENANCE
1. Filter Bag Replacement - When a noticeable drop in suction occurs in the unit or it shuts down,
it may be time to replace the lter bag. Remove the thumb screws on the front of the unit to
remove the front cover plate exposing the lter bag. Remove the lter bag by sliding it off the inlet
tube; the front of the cardboard reinforcement may need to be tilted downward slightly to remove
the bag easily. Check the inside of the lter bag compartment, if dust is present please clean the
compartment. Cause for residual dust may be the lter bag had been improperly installed. Vacuum
out any dust before putting in a new bag, this will increase the life of the unit. Filter bag re-order
number is VMC-A400-5, which can be ordered through your supplier.
2. Installing a new lter bag - Slip the cardboard reinforcement, with rubber seal, over the inlet
tube. Tilt the front of the cardboard downward and slip the back edge up past the tube end; then
rotate upward over the tube end. Then carefully tuck the edges of the lter bag into the lter bag
compartment. Replace the cover plate and gently tighten the screw knobs. Only gentle pressure
need be used to make the gasket seal as the vacuum pressure will draw the cover tightly.
CAUTION: Operating the vacuum with a plugged lter bag can cause permanent damage to the motor.
3. Circuit Protector - The unit is protected by a circuit breaker. Push in to reset.
4. For other maintenance problems or questions consult your dealer or call 1-800-VANIMAN and ask
for SERVICE.
IMPORTANT SERVICE INFORMATION:
SAVE SHIPPING BOX AND FOAM FOR FUTURE
SERVICE. SHIPPING WITHOUT PROPER FOAM
MAY CAUSE DAMAGE TO UNIT
10-1/2"
14-3/8"
14"
14-3/8"
10-1/2"
14"
10-1/2"
14-3/8"
14"
Van-I-Vac
Abrasive Vac
21"
36"
20"
24"
10"
15"
14-1/4"
13-5/8"
10-7/8"
Voyager
Vanguard Platinum 2X
V-Six
StoneVac II Series
SCALE:1:8
SIZE
DWG. NAME
A
REV.
MATERIAL
FINISH
DO NOT SCALE DRAWING
APPLICATION
USED ON
NEXT ASSY
NAME
DATE
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
SHEET 1 OF 1
Industrial Dust Collectors
DESCRIPTION:
REVISIONS
DESCRIPTION
REV.
DATE
APPROVED
PROPRIETARY AND CONFIDENTIAL
ZONE
140 N. Brandon Road - Fallbrook, CA 92028
phone: (760) 723-1498 - fax: (760)723-6990
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
VANIMAN MANUFACTURING COMPANY. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
VANIMAN MANUFACTURING COMPANY IS
PROHIBITED.
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32
ANGULAR:
1º
ONE PLACE DECIMAL
.05
TWO PLACE DECIMAL
.03
THREE PLACE DECIMAL
.005
VANIMAN MANUFACTURING CO.
1/8/2015
PART NO.
1/8/2015
FILE DATE:
eolson
A
B
C
D
123456
