Vaniman Mobile Problast 80017 User manual

SANDBLASTER SAFETY 7/15 Page 1
1. CONDITIONS FOR USE
This micro abrasive blaster may only be operated:
• Indoors;
• Below 6500 ft above sea level altitude;
• Ambient air temperature between 40°-105°F (5-40°C);
• Maximum relative humidity of 80% at 88°F;
• Power supply current fluctuations does not exceed 10% of nominal value;
• Under level 2 contamination conditions;
• Supply cool, dry air only, at a maximum of 150 PSI.
2. SAFETY
• Always disconnect the unit from the compressed air and power sources before beginning any
maintenance.
• When working with the tank wear protective glasses to protect your eyes.
• Any abrasive material on the o-ring may lead to leakage and early wear of the o-ring. After filling, clean the
thread and o-ring before applying the lid.
• Solvents will create cracks in the jar and weaken the jar (danger of explosion!). Clean the lid and tank only
with a dry cloth. Do not write or adhere anything to the jar or lid.
• Check for damages on the lids and tanks regularly and replace them if there is any doubt of the structural
integrity.
• Before operation, check to make certain the lid is secured properly. Using the product without the lid secured
will create a serious explosive hazard.
• Never operate the blasting units without suitable dust extraction and appropriate protective gear. The type
of dust extraction should be based on the type of dust generated. Ask the proper authorities.
• Never direct the blasting material towards eyes or unprotected areas of skin. Improper use can result in risk
of eye or skin injuries.
• Caution: Failure to wear eye protection can result in eye injury. Wear proper eye protection to protect your
vision.
• Do not depress the foot switch when only the compressed air supply hose is connected. The loose hose could
wrap around itself and cause serious injury.
2.1 Liability Exclusion - Vaniman Manufacturing shall be absolved from all claims for damages and warranty if:
• The product is used for any purpose other than it was designed for.
• The product is altered in any way other than those described in the operating instructions.
• The product is repaired by any body other than an authorized facility or if any parts other than Vaniman OEM
parts are used.
• The product continues to be employed, despite obvious safety faults.

MOBILE PROBLAST-I-09/14 Page 1
MOBILE PROBLAST
PACKING LIST
1 - Mobile Problast
1 - Instructions
1 - Additional Quick Disconnect
INSTALLATION & OPERATION
1. Unscrew cap on media storage tank
2. Fill abrasive storage tank to ll line with aluminum oxide micron size specied on tank label. The tank
will hold up to 4 lbs of media. DO NOT OVER FILL as clogging may result.
Part No. Nozzle Size, Inches (mm) Color Recommended Media
Long Lasting Crystal Tips (2 per package)
97902 Medium, .032” (.8mm) Blue 25/50 μm Al2O3
97903 Large, .048” (1.2mm) Black 50/100 μm Al2O3, 50 μm Glass
97904 Extra Large, .065” (1.6mm) Red 100-250 μm Al2O3, 50/100 μm Glass
Precision Tungsten Carbide Tips (1 per package)
97905 Small, .026” (.65mm) Yellow 25 μm Al2O3
97906 Medium, .036”(.91mm) Green 50/100 μm Al2O3, 50 μm Glass
97907 Large, .059” (1.5mm) Violet 100-250 μm Al2O3, 50/100 μm Glass
3. Wipe off excess abrasive and screw cap securely back into place. Do not over-tighten; lid will self
seal when under pressure.
4. Attach your 1/4” ID (inside diameter) hose air supply line to the barbed tting on the back of the unit, on
the right of the small valve. Secure hose with a small screw-type clamp. If necessary remove the tting
and replace with the quick disconnect tting. NEVER depressurize the system by disconnecting the
air supply line while under pressure; abrasive will be forced into the foot valve and regulator, causing
damage. Before disconnecting the air supply line, turn regulator down (counterclockwise) until the
pressure gauge reads zero.
**For more help visit: www.vaniman.com/air-supply-connections-blasters/**
5. Regulate air pressure by turning the air regulator knob. Pull knob up to unlock before turning. Pressure
will indicate pressure reading. DO NOT adjust above 100 psi (7 BARS).
6. Use the foot pedal to start the ow of air and blasting media. Release the foot pedal to stop the ow.

MOBILE PROBLAST-I-09/14 Page 2
MOBILE PROBLAST
MAINTENANCE
Vaniman blasters are designed to be low maintenance. However, as the materials used in a microblaster
are abrasive by design, components do wear out. A few minor areas should be maintained regularly
for a long product life.
Handpieces Hoses:
Check handpiece hoses for wear regularly. When hose feels thin or holes develop, the tubing should
be replaced. On the rear of the unit, where the handpiece hoses come through the cabinet, there is an
aluminum assembly that is a pinch valve for stopping and starting the media ow for the I/O option. This
will be the point of highest wear on the tubing. The hose can be slid back and forth in order to "wear"
a new section of hose. If a hole develops, replace the tubing.
Handpiece Tip Installation:
It is imperative that the handpiece tip and sealing o-ring be installed correctly and securely to avoid
damage or leaks. Install in the manner shown being sure the tip and o-ring seat evenly in the assembly.
Tanks:
When installing the lids on the tanks, be sure the lid is rid of any blasting material or debris. If the tank
or lid begins to wear, replace immediately. Do not overtighten the lid on the unit. The ttings on the
bottom of the tank are designed for easy maintenance of the hoses. To remove a handpiece tubing
from quick disconnect tting, push toward the tank on the plastic ring while pulling the tubing out. Do
not remove the hose ttings while tank is full of media and upright; turn the tank upside down or empty
before removing hoses. To replace, be sure the tting and hose are free of debris or abrasives and
push the hose rmly into the tting. Be sure it goes in until you can see it through the clear wall of the
tank tting. Improper installation will result in leakage and damage to the tanks.
NOTE: Do not remove the hose ttings while tank is full of media and upright; turn the tank upside down
or empty before removing hoses.
Moisture
Vaniman blasters include a Filter for small amounts of oil and moisture. If moisture causes the media
to clump or cake in the tanks, improper media ow will result. Be sure the air supply is relatively oil
and moisture free. An addition of the heavy duty air lter/dryer may solve the problem (See below for
ordering information).
123456
7
Fig. Reorder #
1 2192
2 2191
3 2187
4 2188
5 varies, #4
Included
6 2177
7 97959, #4
& #5 Not
Included

MOBILE PROBLAST-I-09/14 Page 3
MOBILE PROBLAST
REPLACEMENT PARTS
Blasting Media
Part No. Material Size Applications
97921 Aluminum Oxide 25micron Fine surfacing of metal or hard materials.
97922 Aluminum Oxide 50micron Deburring and deashing of metals and other hard materials.
97923 Aluminum Oxide 100micron Aggressive removal of materials, semi-rough nished surface.
97924 Aluminum Oxide 250micron Bulk removal or surface cleaning of tough materials. Rough surface preparation.
97925 Glass Bead 50micron Smoothing/polishing. Cleans and polishes without removing material.
Fig. # Description Reorder Part Number
1Thumb Nut 2266
2Sand Jar Assembly 25 micron
Sand Jar Assembly 50-100 micron
Sand Jar Assembly 110-250 micron
97956
97957
97958
3 Regulator 2303
4Grommet 2819
Not Shown Foot Pedal Assembly 2101
1
2
3
4

MOBILE PROBLAST-I-09/14 Page 4
MOBILE PROBLAST
PLUMBING
Air
Supply
In
Handpiece
Foot
Pedal