Varytec 106697 User manual

Manual
LED Miniflash RGB

2 / 8
Table of contents
1. Safety instructions............................................................................................................................ 3
1.1. For safe and efficient operation...............................................................................................3
2. Designated use ................................................................................................................................ 4
3. Introduction....................................................................................................................................... 5
4. Control.............................................................................................................................................. 5
5. Technical data.................................................................................................................................. 6

1. Safety instructions
•This
device is
•
All modifications to the device will void the warranty.
•
Repairs are to carry out by skilled personnel only.
•
Use only fuses of the same type and original parts as spare parts.
•
Protect the unit from rain and hum
•
Make sure to unplug the power supply before opening the housing.
1.1.
For safe and efficient operation
Be careful with heat and extreme temperature!
Avoid exposing it to direct rays of the sun or near a heating
Not put it in a temperature bellow 32
Keep away from humidity, water and dust!
Do not place the set in a location with high humidity or lots of dust. Containers with water
should not be placed on the set.
To avoid placing on un-
stable location!
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning!
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
If out of work, contact
sales agency immediately!
Any troubles arose, remove the power plug soon, and contact with an engineer for repairing, do not
open the cabinet by yourself, it might result a danger of electric shock.
Take care with the power cable!
Never pull the power cabl
e to remove the plug from the receptacle, be sure to hold the plug. When not
using the device for an extended period of time, be sure to disconnect the plug from the receptacle.
IMPORTANT!
Damages caused by the disregard of this user manual are not subject
accept liability for any resulting defects or problems. Make sure the electrical connection is carried out
by qualified personnel. All electrical and mechanical connections have to be carried out according to
the European safety standards.
Health risk!
Don’t look directly into the light source. At certain circumstances it is
possible that some people get epileptic seizures. This is especially true for
individuals whose epilepsy was determined by a doctor. The device cau
(UV) radiation.
objects and
operate it
By fast flashing, the risk of an epileptic seizure increases. Therefore do not
install it in
danger zones (such as stairs, exit routes ...). Point out the visitors
before operating on the use of a strobe. Avoid prolonged flash sequences
3 / 8
device is
suitable for indoor use (not outdoors) only.
All modifications to the device will void the warranty.
Repairs are to carry out by skilled personnel only.
Use only fuses of the same type and original parts as spare parts.
Protect the unit from rain and hum
idity to avoid fire and electric shocks.
Make sure to unplug the power supply before opening the housing.
For safe and efficient operation
Be careful with heat and extreme temperature!
Avoid exposing it to direct rays of the sun or near a heating
appliance.
Not put it in a temperature bellow 32
°F /0°C, or exceeding 104°F /40°C.
Keep away from humidity, water and dust!
Do not place the set in a location with high humidity or lots of dust. Containers with water
should not be placed on the set.
stable location!
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning!
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
sales agency immediately!
Any troubles arose, remove the power plug soon, and contact with an engineer for repairing, do not
open the cabinet by yourself, it might result a danger of electric shock.
Take care with the power cable!
e to remove the plug from the receptacle, be sure to hold the plug. When not
using the device for an extended period of time, be sure to disconnect the plug from the receptacle.
Damages caused by the disregard of this user manual are not subject
to warranty. The dealer will not
accept liability for any resulting defects or problems. Make sure the electrical connection is carried out
by qualified personnel. All electrical and mechanical connections have to be carried out according to
Don’t look directly into the light source. At certain circumstances it is
possible that some people get epileptic seizures. This is especially true for
individuals whose epilepsy was determined by a doctor. The device cau
(UV) radiation.
Therefore, keep a safe distance (at least
1.5m)
operate it
never without the protective glass
on the front
By fast flashing, the risk of an epileptic seizure increases. Therefore do not
danger zones (such as stairs, exit routes ...). Point out the visitors
before operating on the use of a strobe. Avoid prolonged flash sequences
Use only fuses of the same type and original parts as spare parts.
idity to avoid fire and electric shocks.
Make sure to unplug the power supply before opening the housing.
Do not place the set in a location with high humidity or lots of dust. Containers with water
Any troubles arose, remove the power plug soon, and contact with an engineer for repairing, do not
e to remove the plug from the receptacle, be sure to hold the plug. When not
using the device for an extended period of time, be sure to disconnect the plug from the receptacle.
to warranty. The dealer will not
accept liability for any resulting defects or problems. Make sure the electrical connection is carried out
by qualified personnel. All electrical and mechanical connections have to be carried out according to
Don’t look directly into the light source. At certain circumstances it is
possible that some people get epileptic seizures. This is especially true for
individuals whose epilepsy was determined by a doctor. The device cau
ses
1.5m)
to people and
on the front
page!
By fast flashing, the risk of an epileptic seizure increases. Therefore do not
danger zones (such as stairs, exit routes ...). Point out the visitors
before operating on the use of a strobe. Avoid prolonged flash sequences
.

4 / 8
2. Designated use
The device is only approved for a connection up to 230V 50/60 Hz AC voltage and only for indoor use.
Regular breaks during operation increase the lifetime of your device.
Avoid convulsions or any form of forceful impact during the installation or the start-up of the device.
Make sure that the device is not exposed excessive heat, humidity or dust at the place of installation.
Take care that no cables are lying around. You would endanger your own safety and also the safety of
a third party.
It is not allowed to operate or store the device in an environment in which spray water, rain, humidity
or fog is expected. Humidity or very high atmospheric humidity could reduce the isolation of the device
and could cause deathly electric shocks. If you use fog devices the device has not be exposed to a
direct smoke jet. There has to be a safety distance of at least 0,5m between this device and the fog
machine. Make sure that the saturation of the fog has to enable a visibility of at least 10m.
Fire hazard!!
Make sure when installing the projector, that there are no flammable materials within a distance of at
least 50cm.
Operate the device not during thunderstorms. Surge voltages could destroy the device. Unplug the
power supply during thunderstorms.
Surrounding objects or surfaces should not be in contact with the device.
Make familiar yourself with the functions of the device before start-up. People without the experience
should not handle with the device. The most cause of functional disorder is inappropriate handling.
Do not use chemicals or volatile liquids for cleaning. Use a clean dry cloth to wipe off the dust, or a
wet soft cloth for stubborn dirt.
For transport use the original packing or designated accessory to avoid damages during the transport.
For reasons of safety unauthorized changes are forbidden.
A usage of the device which differs from usages which are described in this manual can cause
damages of the device. In that case the warranty expires. Additional you should notice that every
differed usage is related with dangers and can cause e.g. an electrical short, fire, electric shock or
crash.

5 / 8
3. Introduction
Thank you for buying the LED Miniflash RGB.
4. Control
You can operate the device in two modes:
1. Automatic mode
2. Sound-to-light
With the help of the red switch on the top of the device you can choose between the automatic mode
and sound-to-light mode. If you are in the sound-to-light mode you can set the sensitivity of the
microphone with knob beside the switch.

6 / 8
5. Technical data
Power supply
Voltage 110-240V / 50-60Hz
Power consumption max. 18 W
Light source
Lm type L’ED single color
Color spectrum RGB
Power 12 W
Number / Power 12 x 1 W (4x red, 4x green, 4x blue)
Connections
Strom in Euro plug
Hardware
Protection class IP20
Suitability Indoor
Dimensions 180 x 120 x 50 mm
Weight 0,4 kg

7 / 8

8 / 8
Importer:
B & K Braun GmbH
Industriestraße 2
D-76307 Karlsbad
www.bkbraun.com
[e-mail]