VAT 075 Series Assembly instructions

Installation, Operating &
Maintenance Instructions
601899EC
Edition
2014
-
08
-
20
Door L-VAT
with double acting pneumatic actuator
Series 075
50 × 336 mm (1.97" × 13.23")
This manual is valid for the following product ordering numbers:
075..- .... - ....
Sample picture

Series
075
2
/
29
Edition
2014
-
08
-
20
601899EC
Imprint
Manufacturer
VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Website:
Phone:
Fax:
Email:
www.vatvalve.com
[phone]
[phone]
[email protected]om
Publisher VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Editor VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Print VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Copyright © VAT Vakuumventile AG 2014
No part of these instructions may be reproduced in any way (photo-
copies, microfilms or any other reproduction processes) nor may it be
manipulated with electronic systems, duplicated or distributed without
written permission from VAT. Offenders are liable to pay damages.
The original VAT firmware and updated state of the art versions of the
VAT firmware are intended for use with VAT products. The VAT firmware
contains a limited, time unlimited user license. The VAT firmware may not
be used for purposes other than those intended nor is it permitted to
make copies of the VAT firmware. In particular, it is strictly forbidden to
give copies of the VAT firmware to other people.
The use of trade names, brand names, trademarks, etc. in these
Instructions does not entitle third parties to consider these names to be
unprotected and to use them freely. This is in accordance with the
meaning of the laws and acts covering brand names and trademarks.

Series 075
601899EC
Edition
2014
-
08
-
20
3
/
29
Contents
1 Description of product........................................................................5
1.1 Identification of product....................................................................................5
1.2 Use of product.................................................................................................5
1.3 Used abbreviations..........................................................................................5
1.4 Related documents..........................................................................................5
1.5 Important information.......................................................................................5
1.6 Technical data.................................................................................................5
2 Safety ...................................................................................................6
2.1 Compulsory reading material...........................................................................6
2.2 Danger levels ..................................................................................................6
2.3 Personnel qualifications...................................................................................7
2.4 Safety labels....................................................................................................7
3 Design and Function...........................................................................8
3.1 Design.............................................................................................................8
3.2 Function..........................................................................................................9
4 Installation.........................................................................................10
4.1 Unpacking.....................................................................................................10
4.2 Installation into the system.............................................................................11
4.3 Compressed air connection ...........................................................................12
4.4 Electrical connection......................................................................................12
4.5 Initial operation..............................................................................................13
5 Operation...........................................................................................14
5.1 Normal operation...........................................................................................15
5.2 Operation under increased temperature.........................................................15
5.3 Behavior in case of air pressure drop.............................................................15
5.4 Behavior in case of power failure...................................................................15
5.5 Trouble shooting............................................................................................16
6 Maintenance ......................................................................................17
6.1 Maintenance intervals....................................................................................17
6.2 Required tools...............................................................................................17
6.3 Replacement of actuator pneumatic seals......................................................18
6.4 Replacement of gate .....................................................................................20
7 Repairs...............................................................................................22
8 Dismounting and Storage.................................................................23
8.1 Dismounting..................................................................................................24
8.2 Storage .........................................................................................................24
9 Packaging and Transport.................................................................25
9.1 Packaging .....................................................................................................26
9.2 Transport.......................................................................................................26

Series
075
4
/
29
Edition
2014
-
08
-
20
601899EC
10 Disposal............................................................................................. 27
11 Spare parts........................................................................................ 28

Series 075 DESCRIPTION OF PRODUCT
601899EC
Edition
2014
-
08
-
20
5
/
29
1 Description of product
1.1 Identification of product
The fabrication number and order number are fixed on the product directly or by means of
an identification plate.
made in Switzerland
Fabrication No.:
075 . . - . . . . - . . . . / . . . .
A - . . . . . .


Fabrication number
Order number
1.2 Use of product
Use product for clean and dry vacuum applications only. Other applications are only allowed
with the written permission of VAT.
1.3 Used abbreviations
Abbreviation Description
ATM
Atmospheric
CDA Compressed dry air
Table 1-1
1.4 Related documents
•Product data sheet
•Dimensional drawing
1.5 Important information
This symbol points to a very important statement that requires particular
attention.
Example
:
VAT disclaims any liability for damages resulting from inappropriate packaging.
1.6 Technical data
See product data sheet and dimensional drawing.

SAFETY Series
075
6
/
29
Edition
2014
-
08
-
20
601899EC
2 Safety
2.1 Compulsory reading material
Read this chapter prior to performing any work with or on the product. It contains important
information that is significant for your own personal safety. This chapter must have been
read and understood by all persons who perform any kind of work with or on the product
during any stage of its serviceable life.
NOTICE
Lack of knowledge
Failing to read this manual may result in property damage.
Firstly, read manual.
These Installation, Operating & Maintenance Instructions are an integral part
of a comprehensive documentation belonging to a complete technical
system. They must be stored together with the other documentation and
accessible for anybody who is authorized to work with the system at any
time.
2.2 Danger levels
DANGER
High risk
Indicates a hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING
Medium risk
Indicates a hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION
Low risk
Indicates a hazardous situation which, if not avoided, may result in minor or
moderate injury.
NOTICE
Command
Indicates a hazardous situation which, if not avoided, may result in property
damage.

Series 075 SAFETY
601899EC
Edition
2014
-
08
-
20
7
/
29
2.3 Personnel qualifications
WARNING
Unqualified personnel
Inappropriate handling may cause serious injury or property damage.
Only qualified personnel are allowed to carry out the described work.
2.4 Safety labels
Label Part No. Location on product
T-9001-155 Outer side of both horizontal
actuators
Table 2-1

DESIGN AND FUNCTION Series
075
8
/
29
Edition
2014
-
08
-
20
601899EC
3 Design and Function
3.1 Design
Door type V
Actuator
body mounted to bottom of chamber Door type U Actuator body mounted to chamber wall
Figure 3-1
26
Actuator body 70 O-ring
42 Position indicator 90 O-ring
68 Set screw 99 Screw

Series 075 DESIGN AND FUNCTION
601899EC
Edition
2014
-
08
-
20
9
/
29
3.2 Function
The 075 ATM door consists of two vertical pneumatic cylinders, one pneumatic box and
three horizontal actuators. The vertical cylinders move from open to closed position in the
vertical direction. The horizontal actuators move the gate from the open position to the
closed position in horizontal direction. The gate moves in a so called L-movement.
OPEN CLOSED CLOSED
unlocked locked
1 Gate O-ring
2 Gate
3 Pressure element
4 Pneumatic actuator
Figure 3-2
1
2
4
3

INSTALLATION Series
075
10
/
29
Edition
2014
-
08
-
20
601899EC
4 Installation
WARNING
Unqualified personnel
Inappropriate handling may cause serious injury or property damage.
Only qualified personnel are allowed to carry out the described work.
NOTICE
Insufficient stability
Product will get damaged if it is not stabilized.
Assistant staff required to lift and stabilize the product during mounting.
4.1 Unpacking
•
Make sure that the supplied product is in accordance with your order.
•Inspect the quality of the supplied product visually. If it does not meet your
requirements, please contact VAT immediately.
•Store the original packaging material. It may be useful if the product must
be returned to VAT.
1. Cut plastic straps and open the transport box.
Remove plastic bag in a cleanroom only.
2. Open the plastic bag to unpack gate and actuator.
NOTICE
Sensitive product
Product will get damaged if not handled carefully.
Handle product with care: Do not touch solid objects when lifting the product
and place it down slowly and gently.
3. Place products on a clean surface.

Series 075 INSTALLATION
601899EC
Edition
2014
-
08
-
20
11
/
29
4.2 Installation into the system
WARNING
Hazardous components
Parts, loaded springs, air cushions etc.
may move or release a movement and
cause serious injury.
Do not connect or supply electrical power and compressed air before the
product is completely mounted in the system.
NOTICE
Contamination
Product may get contaminated.
Always wear cleanroom gloves when handling the product.
NOTICE
Insufficient stability
Product may get damaged when actuated at this stage.
Do not operate before product is installed completely into the vacuum system.
NOTICE
Wrong tightening torque
Door and screws may get damaged.
Use tightening torque according to the size of the screws.
•Make sure that sealing surfaces of the door and the chamber are
undamaged. Mount door to a clean system only.
•Make sure that dimensions and tolerances specified on the dimensional
drawing are strictly met.
1. Mount actuator to the chamber, use screws (99) M6×50 mm; see «Figure 3-1»
on page 8.
Quantity of screws depends on mounting position. For U-Type, 3 screws are
required, for V-Type, 4 screws are required.

INSTALLATION Series
075
12
/
29
Edition
2014
-
08
-
20
601899EC
4.3 Compressed air connection
WARNING
Product in open position
Risk of injury when compressed air is connected to the product.
Connect compressed air only when:
– product is installed to the vacuum system
– moving parts cannot be touched
Use clean, dry or slightly oiled air only.
Admissible air pressure range, see product data sheet.
1. Connect compressed air according to the product data sheet and dimensional drawing.
4.4 Electrical connection
WARNING
Product in open position
Risk of injury when product is put into operation.
Keep human body parts away from movable parts.
NOTICE
Wrong voltage
Electrical components may get damaged.
Supply electrical components with the correct voltage.
1. Connect position indicator according to the product data sheet and dimensional
drawing.

Series 075 INSTALLATION
601899EC
Edition
2014
-
08
-
20
13
/
29
4.5 Initial operation
WARNING
Movable parts
Human body parts may get jammed and severely injured.
Keep human body parts away from movable parts.
L-movement requires initializing of compressed air system. The door
command must be set to open at first. This will pressurize the pneumatic
system and ensure the proper L-movement during the following closing
cycles.
1. Open the door.
2. Close the door.

OPERATION Series
075
14
/
29
Edition
2014
-
08
-
20
601899EC
5 Operation
WARNING
Unqualified personnel
Inappropriate handling may cause serious injury or property damage.
Only qualified personnel are allowed to carry out the described work.
WARNING
Movable parts
Human body parts may get jammed and severely injured.
Do not operate before product is installed completely into the vacuum system.
Until actuation of the door keep human body parts away from movable parts.
During operation of the ATM door the pneumatic cylinders move the gate.
There are small gaps with danger of injury, see «Figure 5-1». Take
appropriate measures to avoid possible human injury. Do not insert body
parts through door opening during operation of door.
Small gaps
Figure 5-1

Series 075 OPERATION
601899EC
Edition
2014
-
08
-
20
15
/
29
5.1 Normal operation
The door opens and closes pneumatically.
5.2 Operation under increased temperature
Maximum allowed temperature, see product data sheet.
5.3 Behavior in case of air pressure drop
See product data sheet.
L-movement requires initializing of compressed air system. The door
command must be set to open at first. This will pressurize the pneumatic
system and ensure the proper L-movement during the following closing
cycles.
Proper function of internal nonreturn valve depends on speed of air pressure
drop. Slow pressure drop in air supply will not trigger the nonreturn valve,
therefore the position of the door will be undefined at loss of compressed air
pressure.
1. Open the door.
2. Close the door.
5.4 Behavior in case of power failure
Depending on customer’s installation.

OPERATION Series
075
16
/
29
Edition
2014
-
08
-
20
601899EC
5.5 Trouble shooting
Failure Check Action See
Leak at gate
Check seals and
sealing surfaces Clean sealing surfaces Product data sheet
Damage of gate Replace gate «6.4 Replacement
of gate»
Seal
compression of
gate
Check compressed air Product data sheet
and dimensional
drawing
Door cannot be
operated
Connection of air
lines Check compressed air lines Product data sheet and dimensional
drawing
Connection of
power Check power lines Product data sheet and dimensional
drawing
Gate slides at
chamber wall
Installation and
initial command 1. Move door to open position
2. Attach door to chamber
3. Connect air to “OPEN”-
port” only.
4. Block port “P” so no air
can leave this port
5. Connect air tubing to “P-
port” and apply CDA to
this port
6. Move door to “CLOSED”-
position
Product data sheet
and dimensional
drawing
Compressed air Check compressed air
pressure, requirement:
4 – 7 bar
Air tubing Check correct length and
diameter of compressed air
supply tubing.
Connection of air
lines Check compressed air lines
Table 5-1
If you need any further information, please contact one of our service centers. You will find
the addresses on our website www.vatvalve.com.

Series 075 MAINTENANCE
601899EC
Edition
2014
-
08
-
20
17
/
29
6 Maintenance
WARNING
Unqualified personnel
Inappropriate handling may cause serious injury or property damage.
Only qualified personnel are allowed to carry out the described work.
WARNING
Hazardous components
Human body parts may get jammed and severely injured.
Before starting maintenance:
– disconnect compressed air supply
– disconnect electrical power supply
WARNING
Movable parts
Human body parts may get jammed and severely injured.
Keep human body parts away from movable parts.
6.1 Maintenance intervals
Under clean operating conditions the product does not require any maintenance during
specified lifetime.
•Influences from the process may require more frequent maintenance.
•If the door has reached the specified life cycle – see product data sheet –
we recommend a general overhaul by VAT. Please contact one of our
service centers. You will find the contact data on our website
www.vatvalve.com.
6.2 Required tools
•Allen wrench size 3, 4 and 5
•Torque wrench 4.5 Nm / 6 Nm / 9 Nm
•Cleanroom wiper soaked with alcohol (2% methyl ethyl ketone)
•O-Ring removal tool; see «Table 11-1» on page 28
Figure 6-1

MAINTENANCE Series
075
18
/
29
Edition
2014
-
08
-
20
601899EC
6.3 Replacement of actuator pneumatic seals
NOTICE
Wrong tightening torque
Door body and screws may get damaged.
Use tightening torque according to size of the screws.
NOTICE
Contamination
Product may get contaminated.
Always wear cleanroom gloves when handling the product.
NOTICE
Inappropriate tools
Sealing surfaces may get damaged.
Do not use sharp-edged tools.
The item numbers in brackets refer to «Figure 3-1» on page 8.
1. Vent chambers.
2. Open the door.
3. Disconnect compressed air.
4. Disconnect electrical power supply.
5. Remove the 4 set screws (68) on the back of the pressure plate.
6. Remove pressure plate assembly from the actuator shafts, also remove the 2 O-rings
(70) from the actuator shafts; place these parts in an area where they are protected
from contamination and damage.
7. Remove the screws (99).
8. Remove the actuator assembly from the system.
9. Remove the 4 dowel pins (20) (2 per actuator shaft) and pull the bushing out of the
actuator body «Figure 6-2».
Make sure that the bushings do not get damaged during this action.
10. Remove the actuator shafts from the actuator body.

Series 075 MAINTENANCE
601899EC
Edition
2014
-
08
-
20
19
/
29
11. Remove seals (10), (11), (12), (14), (15), (18) from their position, see drawing below for
details, use O-ring removal tool.
12. Clean and lubricate all grooves for all seals removed in the previous step.
13. Put new seals (10), (11), (12), (14), (15), (18), taken out of the actuator service kit, into
the appropriate grooves.
14. Clean and lubricate the pneumatic cylinder walls in the actuator body.
15. Assemble the door in reverse order
Make sure that both O-rings (70) are in the correct position before the
pressure plate is mounted on the actuator shafts.
16. Tighten the 3 (Type U) or 4 (Type V) screws (99) with a torque of 6 Nm.
Figure 6-2
17. Connect electrical power supply.
18. Connect compressed air supply.
19. Perform one cycle, see chapter «4.5 Initial operation»
Door is ready for use.

MAINTENANCE Series
075
20
/
29
Edition
2014
-
08
-
20
601899EC
6.4 Replacement of gate
NOTICE
Wrong tightening torque
Door body and screws may get damaged.
Use tightening torque according to size of the screws.
NOTICE
Contamination
Product may get contaminated.
Always wear cleanroom gloves when handling the product.
NOTICE
Inappropriate tools
Sealing surfaces may get damaged.
Do not use sharp-edged tools.
1. Vent chambers.
2. Open the door.
3. Disconnect electrical power supply.
4. Disconnect compressed air supply.
5. Remove the 4 set screws (68); see «Figure 3-1», on the back of the pressure plate.
6. While pulling the pressure plate from the shafts, make sure that the 2 O-rings (70) stay
on the shaft or put them back in position right after removing the plate.
7. Remove the 3 screws (75) and washers (61); see «Figure 6-3», and remove gate.
Never use the old, used screws (75) again. If a screw is removed, it has to be
replaced by a new one with fresh adhesive coating; otherwise no safe lock is
guaranteed.
8. Clean or replace gate.
9. Use only the new screws (75) supplied with the spare gate or ordered separately to
reassemble the gate.
10. Before reassembling the gate to the pressure plate, make sure that all the pistons and
washers are at the correct position according to the assembly drawing.
11. Tighten the 3 screws (75) with a torque of 9 Nm; see «Figure 6-3».