Vatech Green 16 User manual

Installation Manual
Model : PHT-65LHS
Version : 1.49
English
Full Version

Notice
Green16/18 Installation Manual v
English
Notice
This manual covers the installation procedures for the Green16/18 dental X-ray unit.
The installation manual is shipped with a hardware unit and the user manual.
Brand name: Green16/18 (Model: PHT-65LHS)
Manufactured by: VATECH Co., Ltd.
In this manual, “equipment” refers to the Green16/18.
In abbreviated forms, CBCT, CEPH, and PANO denote Cone Beam Computed
Tomography, Cephalo, and Panora, respectively. They are interchangeably used.
The “Optional” in this manual means that the function or features are left to the
customer’s or user’s choice
A thorough review of this manual is recommended before installation to ensure the
proper installation of this equipment. The Green16/18 is in steady improvement. The
information contained in this manual may be subject to change without notice,
justification, or notification of the persons concerned.
VATECH Co., Ltd. (manufacturer) reserves intellectual property rights (IPR) for this
manual and the equipment described herein. This IPR is protected by related laws,
and reproduction of this manual, in part or in full, is prohibited without the prior written
consent of the Manufacturer.
This Equipment is covered by one or more of the US patents: US 8634515, US
8634621, US 9117301, US 2015/0117743, US 2015/0139524.
Windows 10, NVIDIA, etc., are 3rd parties’ prominent or registered trademarks
protected by related laws, and these trademarks are used in this manual just only for
explanation.
For further information not covered in this manual or the accompanying
documentation, please contact us with any methods listed below:
Telephone: [phone] / E-Mail: [e-mail]
Website: http://www.vatech.com
Address: 13, Samsung 1-ro 2-gil, Hwaseong-si, Gyeonggi-do, Korea
• Manual Name: Green16/18 (Model: PHT-65LHS) Installation Manual
• Document Number: VHD-IM-068
• Version: 1.49
• Publication Date: 2022-02
The QR code linked to video file about the installation is provided in the
cover of this manual. The smart phone and pad which have the QR code
reader application program can be used to watch video.

Important Notes
vi Green16/18 Installation Manual
Important Notes
Moisture could be built upon the equipment from a sudden temperature
change inside and outside the installation room. Allow at least an hour
before turning ON the equipment to avoid condensation.
To avoid improperly balanced equipment, install the device on a
flat surface to maintain stability.
If the equipment is not stable, property damage and/or personal
injury may occur.
Do not push or pull the equipment.
 Equipment should only be installed by an authorized technician,
complying with proper installation procedures
Failure to read and understand the information provided in the manual
may result in injuries or damages to the equipment. Please read each
CHAPTER in this manual and understand the information therein
before starting any of the installation procedures.

Important Notes
Green16/18 Installation Manual vii
English
Table of Contents
Notice v
Important Notes vi
Table of Contents vii
1. Introduction 1
1.1 Customer’s Responsibility ...................................................................1
1.2 Manufacturer's Liability.......................................................................2
1.3 Conventions in this Manual .................................................................3
1.4 Marks and Symbols..............................................................................9
1.5 Standards and Regulations................................................................11
2. Choosing an Installation Site 12
2.1 Room Requirements ..........................................................................12
2.2 Specifications for Electrical Installation............................................16
2.3 Electrical Requirement ......................................................................16
2.4 Environmental Specifications ............................................................18
2.5 Exposure Switch Installation Options ...............................................19
2.6 Installation Versions .........................................................................21
2.7 Installing the Warning Lamp and Door Interlock Switch ..................22
2.8 Installing the Emergency Stop Switch ..............................................22
3. Before Installing the System 24
3.1 Required Tools...................................................................................24
3.2 Checking the ShockWatch and TiltWatch Indicators.........................26
3.3 Unpacking Boxes ...............................................................................27
3.4 Checking the Parts ............................................................................36
4. Installing the Equipment: Base Stand (Optional) 44
4.1 Assembling the Base and Main Units.................................................44
4.2 Installing the CEPH Unit (Optional)...................................................48
4.3 Installing the Wall and Column Brackets ..........................................52
4.4 Fixing the Base (Optional).................................................................58

Important Notes
viii Green16/18 Installation Manual
4.5 Connecting the Cables to the Equipment. ......................................... 61
4.6 Removing the Transportation Safety Bolts ....................................... 63
4.7 Leveling the Equipment..................................................................... 65
4.8 Tightening the Bolts.......................................................................... 68
5. Installing the Equipment: Wall Mount 69
5.1 Installing the Equipment................................................................... 69
5.2 Installing the CEPH Unit (Optional) .................................................. 74
5.3 Installing the Wall and Column Brackets .......................................... 74
5.4 Connecting the Cables to the Equipment .......................................... 80
5.5 Removing the Transportation Safety Bolts ....................................... 80
5.6 Leveling the Equipment..................................................................... 81
5.7 Tightening the Bolts.......................................................................... 83
6. Completing Miscellaneous Works 85
6.1 Assembling Various Covers ............................................................... 85
6.2 Assembling the Temple Supports and the Chinrest .......................... 87
6.3 Installing the Switch Holders............................................................ 88
7. Setting Up PC 89
7.1 Direct Connection Diagram ............................................................... 89
7.2 The Recommended PC Requirements ............................................... 90
7.3 Disabling Windows Defender ............................................................ 91
7.4 Installing the Internal Peripherals.................................................... 93
7.5 Connecting the Cables to PC ............................................................. 95
8. Setting Up PC Environment Variables 97
8.1 Before Beginning............................................................................... 97
8.2 Turning off the Firewall..................................................................... 98
8.3 Setting up the Power Management Options ..................................... 99
8.4 Turning off the User Account Control.............................................. 101
8.5 Setting Folder Exclusions with Anti-virus Software........................ 102
9. Installing Software 104
9.1 Before Beginning............................................................................. 104

Important Notes
Green16/18 Installation Manual ix
English
9.2 Software Installation Flow ..............................................................104
9.3 Installing the Image Viewer Program .............................................105
9.4 Installing the Install-Package .........................................................105
9.5 Configuring User Information .........................................................120
9.6 Disabling the Packing Mode ............................................................128
9.7 Selecting an Announcement Mode (Optional).................................130
10. Technical Specifications 131
10.1 Mechanical Specifications................................................................131
10.2 Electrical Specifications...................................................................134
10.3 Environmental Specifications ..........................................................135
Appendix 136
A. Installing the Warning Lamp and Door Interlock Switch ................136
B. Installing the Emergency Stop Switch ............................................139
C. Limiting the Column Height.............................................................140
D. Connecting the 3rd party Exposure Switch (Optional) .....................143
E. Checking PC BIOS Settings..............................................................144
F. Installation Checklist.......................................................................145

1. Introduction
Green 16/18 Installation Manual 1
English
1. Introduction
1.1 Customer’s Responsibility
Site planning and preparation are the responsibility of the customer. The following
points should beconsidered fundamentally important to all customers of this product:
Install all required materials before delivery of the system.
Complete the floor, ceiling, and walls of the room before installing the equipment.
Install proper sized junction boxes, with covers, at the necessary locations.
Install a mains power with the proper voltage output and an adequate kVA rating.
Install the circuit breaker specified by this manual.
Provide the installer(s) with the current dimensions of the room, including the
hallway and entry door sizes.
The customer must have an electrician install more than two power outlets in the
room.

1. Introduction
2 Green 16/18 Installation Manual
1.2 Manufacturer's Liability
As the manufacturer, VATECH assumes liability for the safe and reliable installation
and operation ofthis equipment only when:
Equipment installation, including software installation, was carried out by an
authorized agent following this installation manual.
The electrical installation was carried out following the appropriate requirements
specified in IEC-60363.
Genuine original or approved replacement parts are used.
Maintenance/repair service has been performed by a qualified technician(s) from
one of our authorized agents.
The equipment has been used under normal conditions following the user's
manual.
PC Software has been properly used following the manufacturer’s installation
instructions and user manuals.

1. Introduction
Green 16/18 Installation Manual 3
English
1.3 Conventions in this Manual
The following symbols are used throughout this manual to emphasize information or
indicate a potential risk to the equipment or user. Make sure that you fully understand
each symbol and follow the instructions accompanied.
To prevent physical injury and/or damage to the equipment, please observe all
warnings and safety information included in this document.
WARNING
Indicates information that should be
followed with the utmost care. Failure to
comply with a warning may result in severe
damage to the equipment or physical injury
to the operator and/or patient.
CAUTION
Indicates a situation that demands prompt
and careful action, a specific remedy, or
emergency attention.
IMPORTANT
Indicates a situation or action that could
potentially cause problems to the
equipment and/or its operation.
NOTE Emphasizes valuable information or
provides useful tips and hints.
RADIATION Indicates a danger from radiation
exposure.
ESD
susceptibility
Indicates that an item is susceptible to
damage from electrostatic discharges.

1. Introduction
4 Green 16/18 Installation Manual
DO NOT touch or hold the Sensor or Tube Head areas when
moving, installing, or operating the equipment.
DO NOT step on the base unit when installing or operating
the equipment.

1. Introduction
Green 16/18 Installation Manual 5
English
DO NOT use the electric drill to tighten bolts. This can
damage the bolt. Use the tool for drilling the wall only.
You must hold the recommended holding area when moving
the equipment.
<Recommended Holding Area>
Four people are required for the safe installation.
Check the locations of the Emergency Stop Switch and the
Main Power Switch.

1. Introduction
6 Green 16/18 Installation Manual
Cautions for Installation
You must read and understand all instructions in this
manual before installing the equipment.
You must confirm that the system is installed according
to the instructions provided by this manual and perform
the appropriate procedures therein.
Before turning on the equipment, leave it a room
temperature for more than an hour
If the equipment has been stored at temperatures of
below 10℃(50℉) for more than a couple of hours,
allow the equipment to reach room temperature before
applying mains voltage
Installation and related work must be performed by
people authorized by VATECH.
DO NOT connect any items or equipment that is not
part of this system: IEC60601-1-1 (3rd edition: 2005).
Any equipment not approved by VATECH must comply
with the applicable standards: IEC 60950-1 (2nd
edition: 2005) for IT equipment (Ex: PC) and IEC
60601-1 (3rd edition: 2005) for medical electrical
equipment.
All operators of this equipment must ensure that all
requirements outlined in IEC 60601-1-1 (3rd edition:
2005): Safety Requirements for Medical Electrical
Equipment are fully met for the safety of patients,
operators, and the environment.
DO NOT touch-sensitive areas such as the sensor
when installing the equipment. The touch-sensitive
areas are mentioned in relevant sections.
The use of wireless phones may interfere with the
operation of this equipment.
Use an ESD (electrostatic sensitive device) wrist band
to connect it to a ground wire when installing the
equipment.
Touch a ground point to discharge static electricity
before handling PCB boards.
Important Notes for Installation Site
The PC monitor, emergency cut-off switch, and X-ray
Exposure Switch must be located close to the operator

1. Introduction
Green 16/18 Installation Manual 7
English
so that the person can reach out to them easily in an
emergency.
The X-ray room must be shielded accordingly to the
radiation safety requirements to ensure the operator
and patient’s safety. You must verify that the room
meets all applicable safety requirements.
Other devices must not be installed near the X-ray
equipment.
DO NOT install this equipment in an area that is
exposed to strong electromagnetic fields.
DO NOT install this equipment near the explosive
materials or in the explosion-prone area.
The electrical installation of this equipment must follow
all local code requirements for electro-medical systems:
IEC 60364-7-710:2002.
The UPS must be installed at the same time as the
equipment.
The equipment, PC, and all peripheral devices must be
well-grounded.
X-ray Radiation Warnings
Install this equipment in an approved location to ensure
the patient’s and operator’s safety.
Radiation Shielding (e.g., Stationary radiation shielding
barriers) must be installed with the equipment to protect
the operator from radiation exposure.
Follow all federal and local The X-ray system may
cause injury to the patient if improperly used. Obey all
federal and municipal standards regarding radiation
safety.
When the patient is taking an X-ray image, the operator
must stand behind a protective wall or take other
protective actions.
The operator must stay at least 2 m (6 feet) away from
the X-ray source when pressing the Exposure Switch
and observing the patient during the image acquisition.
The operator must provide the patient with protective
clothing before X-ray capturing.
Pregnant women must consult with a doctor before
being exposed to an X-ray.

1. Introduction
8 Green 16/18 Installation Manual
This equipment complies with the following
standards.
IEC60601-1-1:2005 Standard Safety Requirements for
Medical Electrical Equipment
IEC 60601-1-2:2005 Electromagnetic Interference
IEC 60601-1-3:2005 Radiation Protection
IEC 60601-1:2005 Standards for Medical Electrical
Equipment
IEC 60950-1: 2nd edition:2005 Standards for
Information Technology Equipment
IEC60601-2-7 and IEC60601-2-28: X-ray Tube Heads
IEC60364-7-710: 2002 Local Code Requirements for
Electro-medical System Installation
IEC 60601-1-1:2005 regulation shall be met to their full
extent for the safety of the patients, operators, and the
environment—when any person assembles or modify a
medical electrical system by combing it with other
equipment.
Any equipment not provided by VATECH can be
connected when the following standards are complied
with: IEC 60950-1 and IEC 60601-1
The electrical installation shall comply with local code
requirements for electro-medical systems: IEC 60364-7-
710: 2002.

1. Introduction
Green 16/18 Installation Manual 9
English
1.4 Marks and Symbols
Symbols Description Location
Dangerous voltage
Power board /
Inverter board /
Monoblock
Protective earth (Ground) Column
Off (power: disconnected to the Main
Power Switch)
Main Power
Switch
On (power: connected to the Main
Power Switch)
Main Power
Switch
Alternate current Label
Type B Applied Equipment
(IEC 60601-1: Degree of protection
against leakage current and electric
shock: Class 1 equipment)
Label
Radiation hazard Label
Indicates the authorized representative
in the European Community. Label
The CE symbol indicates that this
product complies with the European
Directive for Medical Devices
93/42/EEC as amended by 2007/47/EC
as a class IIb device.
Label
UL mark No. E476672 Label
Caution: Federal law restricts this
device to sale by or on the order of a
licensed healthcare practitioner.
Label
Addresses where the equipment was
manufactured. Label

1. Introduction
10 Green 16/18 Installation Manual
Symbols Description Location
Indicates that electrical and electronic
equipment must not be disposed of as
unsorted municipal waste and must be
collected separately.
Label
Warns ESD hazard. MCU board /
Board package
This indicates that this equipment is
classified as a CLASS 1 LASER
PRODUCT by IEC 60825-1 ED.3
regulations.
Label
This indicates that the user needs to
refer to the Instruction Manual. Label
Indicates the date of manufacture. Label

1. Introduction
Green 16/18 Installation Manual 11
English
1.5 Standards and Regulations
Standards
Green16/18 (PHT-65LHS) is designed and developed to comply with the following
international standards and regulations:
MEDICAL - APPLIED ELECTROMAGNETIC RADIATION EQUIPMENT AS TO
ELECTRICAL SHOCK, FIRE, AND MECHANICAL HAZARDS ONLY IN
ACCORDANCE WITH ANSI/AAMI ES60601-1 (2005) + AMD 1 (2012),
CAN/CSA-C22.2 No. 60601-1 (2014)
21 CFR 1020.30, 31, 33
NEMA Standard publication PS 3.1-3.18, 2008
This is Class IIb equipment and obtained CE marking
in April 2007 for regulations compliance following the
revised European Union’s MDD (Medical Devices
Directive) 93/42 EEC.
MEDICAL - APPLIED ELECTROMAGNETIC
RADIATION EQUIPMENT AS TO ELECTRICAL
SHOCK, FIRE, AND MECHANICAL HAZARDS ONLY
IN ACCORDANCE WITH ANSI/AAMI ES60601-1
(2005) + AMD 1 (2012), CAN/CSA-C22.2 No. 60601-1
(2014)
Classifications (IEC 60601-1 6.1)
The degree of protection against water ingress: Ordinary Equipment: IPX0
The degree of protection against electric shock: Class 1 equipment, Type B
Applied Parts (Temple Supports, Chinrests and cover, Nasal Positional and
cover, Ear Rod and cap, Carpus Plate)

2. Choosing an Installation Site
12 Green 16/18 Installation Manual
2. Choosing an Installation Site
2.1 Room Requirements
The location of this equipment should allow for high
visibility of the patient by the operator, and the operator
should be as about the patient as possible.
This equipment should not be installed on thick carpets
for stability reasons.
Anti-static floor materials should be used around the
equipment.
The PC monitor, emergency cut-off switch, and X-ray
Exposure Switch should be installed in the vicinity of
the operator so that he or she can manage them
simultaneously in case of emergency.
<Without CEPH Unit (optional): 2,055 mm (L) x 2,495.8 mm (W) or wider >