Vatech Pax-i PCH-2500 User manual

Installation Manual
Full version
Model: PCH-2500
Version: 3.06
• English

PaX-i (PCH-2500) Installation Manual
04
Notice to the Installers
Notice
This manual covers the installation procedures for the PaX-iTM dental X-Ray unit. An installation manual and user
manual are shipped with each hardware unit.
Product name: PaX-iTM (Model: PCH-2500)
Manufactured by VATECH Co., Ltd.
In this manual, Equipment refers to the PaX-iTM.
In abbreviated forms, CEPH and PANO denote Cephalometric and Panoramic, respectively.
The “Optional” in this manual means that the function or features are left to customer’s or user’s choice
A thorough review of this manual is recommended before installation to ensure the proper installation of
this equipment. The PaX-i is in steady improvement. The information contained in this manual may be
subject to change without notice, justication or notication of the persons concerned.
VATECH Co., Ltd. (Manufacturer) reserves intellectual property rights (IPR) for this manual and the
equipment described herein. This IPR is protected by related laws and reproduction of this manual, in
part or in full, is prohibited without the prior written consent of the Manufacturer.
This Equipment is covered by one or more of the US patents:
US7995704, US8634515, and US9117301.
Windows 7/8/10, NVIDIA, etc. are third parties’ prominent or registered trademark protected by related
laws and these trademarks are used in this manual just only for explanation.
For further information not covered in this manual or in the accompanying documentation, please
contact us with any method listed below:
Telephone: [phone]
E-Mail: [email protected]
Website: http://www.vatech.co.kr
Address: 13, Samsung 1-ro 2-gil, Hwaseong-si, Gyeonggi-do, Korea

PaX-i (PCH-2500) Installation Manual 05
Notice to the Installers
Important Information
When installing the equipment under sudden temperature change inside
and outside of the building, which could cause moisture condensation on it,
allow at least an hour before turning ON the equipment
Failure to read and understand the information provided in this manual may
result in physical injury, damage to the equipment or equipment failure.
Please read each CHAPTER in its entirety and understand the information
therein before attempting any of the installation procedures.
1. To avoid improperly balanced equipment, install the device on a flat
surface to maintain stability.
2. If the equipment is not stable, property damage and/or personal injury
may occur.
3. Do not push or pull the equipment.
4. Equipment should only be installed by an authorized technician,
complying with proper installation procedures.

PaX-i (PCH-2500) Installation Manual
06
Notice to the Installers
Location of the power and emergency stop switches
ON/OFF SWITCH
EMERGENCY SWITCH

PaX-i (PCH-2500) Installation Manual 07
Notice to the Installers
Conventions Used in this Guide
The following symbols are used throughout this manual to emphasize information or indicate a
potential risk to the equipment or user. Make sure that you fully understand each symbol and obey the
instructions which appear to the right of the symbol.
Notes help you optimize system performance. Carefully read each note to ensure
that the equipment is used to its full potential.
Cautions indicate a situation that demands prompt but careful action, remedy or
emergency attention.
Warnings indicate information that should be followed with the utmost precision.
Failure to comply with warnings may result in severe damage to the equipment and/
or physical injuries to the patient or operator.
Radiation symbols indicate a possible danger from exposure to radiation.
Important symbols indicate a compulsory action or instruction.
ESD susceptibility symbols indicate that an item is susceptible to damage from
electrostatic discharges.

PaX-i (PCH-2500) Installation Manual
08
Notice to the Installers
Never touch or hold the sensor or tube head areas while moving, installing
or operating this equipment.
Sensor
Tube head
Handle frame

PaX-i (PCH-2500) Installation Manual 09
Notice to the Installers
Do not step on the base of the unit while installing or operating the
equipment.
Do not use an electric drill until the installation is over.
Recommended holding area during transportation(OK)
3 installers are required to install the equipment safely.

PaX-i (PCH-2500) Installation Manual
10
Notice to the Installers
Cautions
1. It is critical that installers read and understand the installation instructions
fully before installation.
2. The installer must confirm that the system is installed according to
the instructions provided by this manual and perform the appropriate
procedures therein.
3. If the equipment has been stored at temperatures of below 10℃(50℉)
for more than a couple of hours, allow the equipment to reach room
temperature before applying the mains voltage.
4. Installation and related work must only be performed by people authorized
by VATECH.
5. Do not connect any items or equipment to this system which are not part of
the system: IEC60601-1-1
6. Any equipment not approved by VATECH must comply with the applicable
standards: IEC 60950-1 for IT equipment (Ex: PC) and IEC 60601-1 for
medical electrical equipment.
7. All operators of this equipment are responsible for ensuring that the
requirements outlined in IEC 60601-1-1: Safety Requirements for Medical
Electrical Equipment are fully met to ensure the safety of patients,
operators and the environment.
8. Never touch-sensitive areas such as sensors during installation. These
areas are indicated at the applicable stages during the installation
procedures.
9. The use of wireless phones may interfere with the operation of this
equipment.
10. Use an ESD (electrostatic sensitive device) wristband during installation
and connect it to a ground wire.
11. Touch a ground point to discharge static electricity before handling PCB
boards.