Vava VA-LTS005 User manual

ADJUSTABLE ALR SCREEN
FOR UST PROJECTOR
VA-LTS005
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch

2
English
3 –17
Čeština
18 –32
Slovenčina
33 –47
Magyar
48 –62
Deutsch
63 –77

3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
✉www.alza.co.uk/kontakt
✆[phone]
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

4
Thank you for choosing the VAVA Projection Screen. Please read this User Guide
thoroughly before use and retain it for future reference.
With the constant optimization of the projector, instructions in this User Guide may not
be totally applicable to the actual product.
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INFORMATION AND
INSTRUCTIONS. KEEP FOR FUTURE REFERENCE.
CAUTION
For optimal projection, safe installation and lonp lasting use of the screen, please always
follow below instructions carefully:
•Always handle the screen on a clean, level surface covered with clean cloth, film,
etc.
•Gently hold and put down the unit to avoid any damage to the screen surface.
•Do not touch the screen surface by hand. Before handling the screen, put on the
pairs of gloves to avoid fingerprint, dust or hand oil on the screen surface.
•Do not poke the screen surface with any sharp or hard objects to avoid scratches
or tears.
•It is recommended to clean the screen once every two weeks.
•Wipe clean the screen with a soft cloth and lukewarm water. For General dust,
use a soft brush (rough towels or cloth may damage the screen) to clean the
screen surface.
•Do not clean with abrasive detergent, solvent or other coarse chemicals to avoid
permanent damage to the screen surface.
•You may notice a slight smell for first-time use, which will dissipate over time. If
the smell
•is too strong, open a window to ventilate the room.
•Child ren should be supervised to ensure that they do not play with the screen.
•Please contact your local dealer for repair or maintenance. For any questions or
concerns, please email us at [e-mail] or call us at [phone].
READ AND SAVE THESE INSTRUCTIONS

5
Package Contents
2 x Inner Frames (Expand
to form a quadrilateral)
2 x Struts (Without hooks)
1 x Struts (Without hooks)
4 x Outer Frame I (one
bevel)
2 x Outer Frame II (two
bevels)
1 x ALR Screen
4 x Inner Frame Corner
Connectors
2 x Inner Frame
Connectors
4 x Fiberglass Strips (Short)
2 x Fiberglass Strips (Long)
4 x Corner Protectors
4 x Wall Hangers
18 x M4*8 Screws (For
Strut and Outer Frame)
28 x M5*8 Screws (For
Inner Frame Connectors)
2 x Anti-dirt Gloves
2 x Hexagon Wrenches
8 x Wall Anchors with
Screws

6
2 x Hooks
1 x Wall Drilling Template
How to Setup
1. Unpack the frames and place the packag i ng material underneath to keep them
protected.
2. Please wear the included protective gloves before handling in case of scratches from
metal parts.
Assemble the Inner Frames
1) Take out the two Inner Frames.

7
2) Expand the Inner Frames.
3) Fix the Inner Frame Connectors.
Inner Frame I
Inner Frame II
2 x Inner Frame
Connectors
2 x M5*8 Screws
16 x M5*8 Screws
4 x Inner Frame Corner
Connectors

8
4) Assemble the Struts.
Assemble the Screen
1) Place a piece of clean and soft cloth or plastic film onto a flat surface.
2) Wear the included anti-dirt gloves before handling the screen to avoid fingerprint
smudges.
3) Unpack the screen, gently unroll it onto the cloth or plastic film with its back facing
upwards.
18 x M4*8 Screws
Without hooks
With hooks
—
__ With hooks

9
4) Insert the fiberglass strips into the screen sides: 1 longer strip into the short screen
side, 2 shorter strips into the lonp screen side. Make sure the shorter ones in the long
screen sides are well aligned with each other.
Black side facing upwards
Fiberglass strips

10
5) Put the installed inner frame onto the back side of the screen.
6) Attach the screen onto the inner frame using the tension springs. Install the tension
sprints to the four corners in the sequence 1 3 first. Then install the other tension
springs to both sides from the frame center as shown below (please pull the springs
with force at the same time).
Inner Frame
Screen
Black side facing
upwards
Black side facing
upwards
Inner Frame (Alipn
the four
corners of the
screen and inner
frame well)
Screen

11
Note:
•Pull the tension springs with hooks.
•Hang the tension spring on the fiberglass strips.
•It is strongly recommended that two people pull the tension springs on opposite
sides at the same time.
7) Place the screen upright to check its even ness. If the screen is not stretched tight,
tighten throup h the six adjusting bolts (A as shown below).
Hook for pulling the
spring
Hexagon Wrench
for adjustment
Loosen
Tighten

12
Assemble the Outer Frames and Corner Protectors
1) Place the outer frames against the border of the frame, align the four corners. Fix the
inner frames with the outer ones using the included M4*8 screws.
2) Fix the plastic corner protectors onto the four corners. Make sure they are well
aligned with the outer frames in case of falling.
12 x M4*8 Screws
Outer Frame II
Outer Frame I
Outer Frame II
Outer Frame I
Outer Frame
Outer Frame
Corner Protector

13
Mount the Screen onto Wall¨
1) Mount the wall hangers onto the wall with a horizontal distance of 130cm / 51.2in and
vertical distance of 70cm / 27.6in. Please estimate the location of the screen to be
mounted as per the projector used. Generally, distance between the lower edge of the
frame and ground is 60-80cm / 23.6-31.5in.It
Note: Fix one hanger first, then use the wall drilling template to facilitate locating the
position of the remaining hangers.
2) Mount the screen onto the wall as shown below.
4 Wall Hangers
Wall
Screen
Ground
Before After

14
Screen Height Adjustment
1) Adjust the screen height via the height adjusters on the struts if you have already
fixed the wall hangers.
2) The height adjusters on the struts are locked to “0" by default.
3) Please adjust as shown below.
Note: Make sure the four height adjusters are set to the same scale.
Specification
Model
VA-LTS005
Projection Area
2214 x 1245 mm / 87.2 x 49.0 in
Aspect Ratio
100” 16:9
Dimensions
2234 x 1265 x 27 mm / 88.0 x 49.8 x 1.1in
Net Weight
15.2kg
Originally set to "0”.
Slightly unscrew the
two screws, move the
adjuster to the desired
scale and tighten.

15
Warranty Conditions
A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you
need repair or other services during the warranty period, contact the product seller
directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for
which the claimed claim may not be recognized:
•Using the product for any purpose other than that for which the product is intended
or failing to follow the instructions for maintenance, operation and service of the
product.
•Damage to the product by a natural disaster, the intervention of an unauthorized
person or mechanically through the fault of the buyer (e.g. during transport, cleaning
by inappropriate means, etc.).
•Natural wear and aging of consumables or components during use (such as
batteries, etc.).
•Exposure to adverse external influences, such as sunlight and other radiation or
electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage,
electrostatic discharge voltage (including lightning), faulty supply or input voltage and
inappropriate polarity of this voltage, chemical processes such as used power
supplies, etc.
•If anyone has made modifications, modifications, alterations to the design or
adaptation to change or extend the functions of the product compared to the
purchased design or use of non-original components.

16
EU Declaration of Conformity
Identification data of the manufacturer's / importer's authorized representative:
Importer: Alza.cz a.s.
Registered office: Jankovcova 1522/53, Holešovice, 170 00 Prague 7
IČO: 27082440
Subject of the declaration:
Title: ADJUSTABLE ALR SCREEN FOR UST PROJECTOR
Model / Type: VA-LTS005
The above product has been tested in accordance with the standard(s) used to
demonstrate compliance with the essential requirements laid down in the
Directive(s):
Directive No. (EU) 2014/35/EU
Directive No. (EU) 2014/30/EU
Directive No. (EU) 2014/53/EU
Directive No. (EU) 2011/65/EU as amended 2015/863/EU
Prague, 18.10. 2021

17
WEEE
This product must not be disposed of as normal household waste in accordance with
the EU Directive on Waste Electrical and Electronic Equipment (WEEE - 2012/19 / EU).
Instead, it shall be returned to the place of purchase or handed over to a public
collection point for the recyclable waste. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of
this product. Contact your local authority or the nearest collection point for further
details. Improper disposal of this type of waste may result in fines in accordance with
national regulations.

18
Vážený zákazníku,
Děkujeme vám za zakoupení našeho produktu. Před prvním použitím si prosím pečlivě
přečtěte následující pokyny a uschovejte si tento návod k použití pro budoucí použití.
Zvláštní pozornost věnujte bezpečnostním pokynům. Pokud máte k přístroji jakékoli
dotazy nebo připomínky, obraťte se na zákaznickou linku.
✉www.alza.cz/kontakt
✆[phone]
Dovozce Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

19
Děkujeme, že jste si vybrali projekční plátno VAVA. Před použitím si prosím
důkladně přečtěte tuto uživatelskou příručku a uschovejte si ji pro budoucí
použití.
Vzhledem k neustálé optimalizaci projektoru nemusí být pokyny v této uživatelské
příručce zcela použitelné pro skutečný výrobek.
DŮLEŽITÉ BEZPEČNOSTNÍ POKYNY
PŘEČTĚTE SI VŠECHNY BEZPEČNOSTNÍ INFORMACE A POKYNY A
DODRŽUJTE JE. USCHOVEJTE PRO BUDOUCÍ POUŽITÍ.
POZOR
Pro optimální projekci, bezpečnou instalaci a dlouhodobé používání plátna vždy pečlivě
dodržujte níže uvedené pokyny:
•S plátnem vždy manipulujte na čistém, rovném povrchu pokrytém čistým
hadrem, fólií apod.
•Přístroj pokládejte jemně, aby nedošlo k poškození povrchu.
•Nedotýkejte se povrchu plátna rukou. Před manipulací si nasaďte rukavice,
abyste zabránili otiskům prstů, prachu nebo oleji z rukou na povrchu.
•Na plátno nedávejte žádné ostré nebo tvrdé předměty, aby nedošlo k poškrábání
nebo roztržení.
•Doporučuje se čistit jednou za dva týdny.
•Otřete měkkým hadříkem a vlažnou vodou. V případě prachu použijte k čištění
povrchu měkký kartáč (hrubé ručníky nebo hadříky mohou povrch poškodit).
•Aby nedošlo k trvalému poškození povrchu, nečistěte ji abrazivními čisticími
prostředky, rozpouštědly ani jinými hrubými chemikáliemi.
•Při prvním použití můžete zaznamenat mírný zápach, který se časem rozptýlí.
Pokud je zápach příliš silný, otevřete okno, abyste místnost vyvětrali.
•Na děti je třeba dohlížet, aby si nehrály s plátnem.
•Pro opravu nebo údržbu se obraťte na místního prodejce. V případě jakýchkoli
dotazů nebo problémů nám napište na s[email protected]m nebo zavolejte na
[phone].
PŘEČTĚTE SI A ULOŽTE TYTO POKYNY

20
Obsah balení
2 x vnitřní rámy
(Rozbalte je tak, aby tvořily
čtyřúhelník)
2 x vzpěry
(bez háčků)
1 x vzpěry
(bez háčků)
4 x vnější rám I
(jedno zkosení)
2 x vnější rám II
(dvě zkosení)
1 x plátno ALR
4 x vnitřní rohové spojky
rámu
2 x konektory vnitřního
rámu
4 x sklolaminátové pásky
(krátké)
2 x sklolaminátové pásky
(dlouhé)
4 x chrániče rohů
4 x nástěnné věšáky
18 x šrouby M4*8
(pro vzpěru a vnější rám)
28 x šrouby M5*8
(pro konektory vnitřního
rámu)
2 x rukavice proti
nečistotám
2 x šestihranné klíče
8 x nástěnné kotvy se
šrouby