Vector TCI2 Series Operational manual

TCI2
PRODUCT DATA SHEET
Doc: 70-07-0703B, 20220426 © Vector Controls LLC, USA Page 1-10
Subjects to alteration www.vectorcontrols.com
VECTOR
Universal Programmable Controller TCI2
The TCI2 is a programmable universal controller with communication capabilities. Each control loop may use 2 PI sequences
and 2 binary stages. The TCI2 comes with a built-in RS485 communication interface that allows peer-to-peer communication
with an operation terminal such as OPA2-(2TH)-VC. The TCI2 uses the universal X2 operating system. Serial communication
options are realized with Modbus RTU/ASCII and BACnet MS/TP. There is also a Wi-Fi and Ethernet communication option
available which supports Modbus TCP and BACnet IP. An embedded webserver provides a web interface to access the
controller in order to change the connection settings and to operate the controller.
Complete parameter sets may be copied by use of an accessory called AEC-PM2 or exchanged with a PC using an RS485-USB
converter, Wi-Fi or Ethernet communication and the EasySet program.
Functions
•Two universally configurable control loops:
oFunctions for dehumidifying, set point shift and cascade control
oMultiple auxiliary functions: heat-cool auto changeover, automatic enable, set point compensation
oFree heating and cooling with economizer function based on enthalpy or temperature
oDifferential, averaging, min and max functions, enthalpy and dew point calculations
oTransmitter function for inputs and set points
•4 selectable universal inputs (VDC, mA, NTC, Pt1000) and 2 analog outputs (VDC, mA)
•2 relays with each a normally open contact (SPST NO)
•8 freely assigned alarm conditions, selectable state of outputs on alarm condition
•Power Cap protected real-time clock with 48hr power backup
•7-day programmable schedules, with options including change of set points and direct position of manual outputs
•Password protected programmable user and control parameters
•Peer to peer communication to optional X2 operation terminal OPxx-VC
•Communication over Modbus, BACnet, Ethernet or Wi-Fi (optional interface required)
•Webserver that supports TCI2 operation trough mobile devices or EasySet IP access (Ethernet or Wi-Fi interface
required)
Wi Fi

TCI2
PRODUCT DATA SHEET
Doc: 70-07-0703B, 20220426 © Vector Controls LLC, USA Page 2-10
Subjects to alteration www.vectorcontrols.com
VECTOR
Types and Ordering
Product Name
Product No.
Loop
UI
DO
AO
COM
Functions
TCI2-222.200
40-110125
2
2 NTC+2 VDC
2
0
Stand alone
24 V low cost
TCI2-204.202UC-OP
40-110115
2
4
2
2
Stand alone
24 V with display
TCI2-204.202UC-OP-L
40-110114
2
4
2
2
Stand alone
100 –250 VAC with display
TCI2-204.202UC-MOD
40-110107
2
4
2
2
Modbus RTU/ASCII
24 V, RS485
TCI2-204.202UC-OP-MOD
40-110109
2
4
2
2
Modbus RTU/ASCII
24 V. RS485 with Display
TCI2-204.202UC-OP-MOD-L
40-110110
2
4
2
2
Modbus RTU/ASCII
100 –250 VAC, RS485 with display
TCI2-204.202UC-BAC
40-110111
2
4
2
2
BACnet MS/TP
24 V. RS485
TCI2-204.202UC-OP-BAC
40-110113
2
4
2
2
BACnet MS/TP
24 V, RS485 with display
TCI2-204.202UC-WEM
40-110123
2
4
2
2
Modbus TCP
24 V, TCP/IP - WI-FI
TCI2-204.202UC-WEM-L
40-110122
2
4
2
2
Modbus TCP
100 - 250 VAC, TCP/IP - WI-FI
TCI2-204.202UC-ETM
40-110124
2
4
2
2
Modbus TCP
24 V, TCP/IP - Ethernet
TCI2-204.202UC-WEB
40-110131
2
4
2
2
BACnet IP
24 V, TCP/IP - WI-FI
TCI2-204.202UC-WEB-L
40-110130
2
4
2
2
BACnet IP
100 - 250 VAC, TCP/IP - WI-FI
TCI2-204.202UC-ETB
40-110132
2
4
2
2
BACnet IP
24 V, TCP/IP - Ethernet
UI = Universal input, DO = Digital output, AO = Analog output, COM = Communication
Accessories
Product Name
Product No.
Description
Communication
AEX2-MOD
40-500105
Modbus RTU or ASCII communication
AEX2-BAC
40-500106
BACnet MS/TP communication
AEC-SMA-01
40-500146
Antenna cable kit for external mounting of the Wi-Fi antenna (cable length 1 m)
Mounting
AMM-2
40-510023
Mounting kit for panel mounting of the TCI2
Memory
AEC-PM2
40-500103
Plug-In memory module for saving and fast copying of parameter sets
External Operation Terminal
OPT1-xx
40-50xxxx
A large range of external operation terminals may be found on our website
www.vectorcontrols.com. All -VC type operation terminals work with this controller.
OPA2-xx
40-50xxxx
Safety
DANGER! Safety advice
This device is for use as an operating controller. It is not a safety device. Where a device failure could endanger
human life and property, it is the responsibility of the client, installer and system designer to add additional
safety devices to prevent such a device failure. Ignoring specifications and local regulations may cause equipment
damage and endangers life and property. Tampering with the device and misapplication will void warranty.

TCI2
PRODUCT DATA SHEET
Doc: 70-07-0703B, 20220426 © Vector Controls LLC, USA Page 3-10
Subjects to alteration www.vectorcontrols.com
VECTOR
Technical specifications
Power supply
Operating voltage TCI2-204.202U
24 VAC ±10%, 50/60 Hz, 12…34 VDC
Safety extra-low voltage (SELV)
HD 384, Class II
Operating voltage TCI2-204.202U-L
85…264 VAC, 50/60 Hz, 120…370 VDC
Power consumption
Max. 3 VA
Clock backup
Min. 48 hours
Signal inputs
Universal input
Input signal
Resolution
Impedance
Input jumper set for voltage or current
0…10 VDC or 0…20 mA
9.76 mV or 0.019 mA (10 bit)
Voltage: 74.8kΩ, Current: 158Ω
Input jumper set to temperature (RT) or digital input (DI)
Passive input
Type & range:
NTC (Sxx-Tn10) 10kΩ@25°C: -40…100 °C (-40…212 °F)
PT1000 (Sxx-Tp2): -50…205 °C (-58…401 °F)
NI1000 (Sxx-Tk5): -50…180 °C (-58…356 °F)
Signal outputs
Analog outputs: Output signal
Resolution
Maximum load
0...10 VDC or 0…20 mA
9.76 mV or 0.019 mA (10 bit)
Voltage: ≥1kΩ Current: ≤250Ω
Relay outputs: AC Voltage
(SPST NO) DC Voltage
0…250 VAC, full-load current 3A, locked-rotor 18A.
0…30 VDC, full-load current 3A, locked-rotor 18A.
Insulation strength between relays contacts
and system electronics:
between neighboring contacts:
4000 VAC to EN 60 730-1
1250 VAC to EN 60 730-1
Electrical
connections
Connector type
Screw terminal connectors for wire 0.34…2.5 mm2
(AWG 22…12)
Remote terminal
RS485 in accordance with EIA/TIA 485, Shielded twisted
pair cable
Environment
Operation
Climatic conditions
Temperature
Humidity
To IEC 721-3-3
class 3K5
0…50 °C (32…122 °F)
<85 % RH non-condensing
Transport & storage
Climatic conditions
Temperature
Humidity
Mechanical conditions
To IEC 721-3-2 and IEC 721-3-1
class 3K3 and class 1K3
-25…70 °C (-13…158 °F)
<95 % RH non-condensing
class 2M2
Standards
Degree of protection
IP30 to EN 60 529
Pollution class
II (EN 60 730-1)
Safety class: TCI2-202.202U
TCI2-204.202U-L
III (IEC 60536) if SELV is connected to DO, else II
II (IEC 60536)
Overvoltage category
III (EN 60 730-1)
General
Material
Fire proof ABS plastic (UL94 class V-0)
Dimensions (H x W x D)
57 x 93 x 115 mm (2.4 x 3.7 x 4.5) inch
Weight (including package)
TCI2 (24V) without display / with display
TCI2 (230V without display / with display
245g (8.6oz) / 290g (10.2oz)
275g (9.7oz) / 320g (11.3oz)
Technical specification for serial communication -MOD and -BAC types
Network
Hardware interface
Max nodes per network
Max nodes per segment
RS485 in accordance with EIA/TIA 485
128
64 (Vector devices only)
Conductors
Impedance
Nominal capacitance
Shielded Twisted Pair (STP) cable
100 - 130 ohm
100 pF/m 16 pF/ft. or lower
Galvanic isolation
The communication circuitry is isolated
Line termination
Network topology
A line termination resistance (120 ohm) shall be connected
between the terminals (+) and (-) of the furthermost node
of the network
Daisy chain according EIA/TIA 485 specifications
Recommended maximum length per chain
1200 m (4000 ft.)

TCI2
PRODUCT DATA SHEET
Doc: 70-07-0703B, 20220426 © Vector Controls LLC, USA Page 4-10
Subjects to alteration www.vectorcontrols.com
VECTOR
Modbus
(-MOD)
Communication standard
Modbus (www.modbus.org)
Default setting
19200 baud rate, RTU 8 data bits,
1 even parity bit, 1 stop bit
Communication speed
4800, 9600, 19200, 38400
Protocol: Data bits
Parity –stop bit
RTU - 8 data bits, ASCII –7 data bits,
no parity –2 stops, even or odd parity –1 stop
BACnet
(-BAC)
Communication standard
BACnet MS/TP over RS485
BTL tested and listed B-ASC
Communication speed
9600, 19200, 38400, 57600, 76800, 115200
Technical specification for TCP/IP communication -WEM, WEB, -ETM and -ETB types
Wi-Fi
Standards
Wi-Fi Alliance
FCC/CE-RED/IC/TELEC/KCC/SRRC/NCC
802.11 b/g/n (802.11n up to 150 Mbps)
A-MPDU and A-MSDU aggregation and 0.4 µs guard interval
support
Frequency range
2.4 GHz ~ 2.5 GHz
Antenna
External
Ethernet
Compliant with
IEEE802.3/802.3u (Fast Ethernet)
ISO 802-3/IEEE 802.3 (10BASE-T)
Speed
10/100 BASE-T (10Mbit/s, 100Mbit/s)
Modbus TCP
(-WEM)
(-ETM)
Standard
IEC 61158
Communication protocol
Modbus TCP (www.modbus.org)
Transport Layer
TCP/IP
TCP/IP Port
502
BACnet/IP
(-WEB)
(-ETB)
Communication standard
BACnet/IP
BTL tested and listed B-ASC
Transport Layer
UDP
UDP Port
47808
Product testing and certification
Declaration of
conformity
Information on the conformity of our products can be found on our website
www.vectorcontrols.com on the corresponding product page under "Downloads".
Dimensions, mm (inch)
57 (2.2)
93 (3.7)
93 (3.7)
46 (1.8)
45 (1.8)
115 (4.5)
WiFi-Antenna only on -WEM, -WEB
Ethernet plug only on
-ETM , -ETB
Reset button TCP/IP only on
–WEM, -WEB, -ETM, -ETB
Status-LED

TCI2
PRODUCT DATA SHEET
Doc: 70-07-0703B, 20220426 © Vector Controls LLC, USA Page 5-10
Subjects to alteration www.vectorcontrols.com
VECTOR
Mounting and Installation
Mounting location
•In a cabinet on a flat surface
•In a cabinet on a top-hat rail
•In a panel (cabinet door) with the optional panel mounting kit
•The following mounting locations should be avoided:
oFor the types with wireless transmission (-WEM or -WEB), avoid locations that interfere with the radio signals,
e.g. metal boxes or devices that generate electrical interferences.
Mounting instructions
See the TCI2 installation sheet, document no. 70-00-0688 or 70-00-0893 (www.vectorcontrols.com).
Selection of sensors and actuators
Temperature sensors
Use Vector Controls NTC sensors to achieve maximum accuracy: SDB-Tn10-20 (duct), SRA-Tn10 (room), SDB-Tn10-20 +
AMI-S10 as immersion sensor.
Actuators
Choose modulating actuators with an input signal type of 0-10 VDC or 4-20 mA (min. and max. signal limitations may be set
with parameters).
3-point actuators with constant running time are recommended.
Binary auxiliary devices (e.g. pumps, fans, on/off valves, humidifiers, etc.)
Do not directly connect devices that exceed specified limits in technical specifications –observe start up current on inductive
loads.
Connection diagram
Type: TCI2-204.202
OPT1-xx
OPA2-xx
N L
(-MOD) (-BAC)
RS485
85..264 VAC
Operation
Terminal
GND
UI1
UI2
Digital Output (2x)
Power
Relays 3A
Universal Input (4x)
NTC 10k
,
Pt1000
0...10 VDC, 0...20 mA
UI3
UI4
AO1
AO2
Analog
Output (2x)
0...10 VDC,
0...20 mA
Status LED
A
c
t
u
-
a
t
o
r
AO
GND
GND
UI
NTC
10k

PT1000
UI
GND
0…10 VDC
0…20 mA
UI
GND
Line Termination (LT)
Shielded Twisted Pair (STP)
120
Ω
(LT)
GND
V+
24V AC/DC
3 VA
GND
Vop
+
_
STP
OPXX-VC
1
2
3
4
120
Ω
JP7
OP3
OP1
OP4
OP2
24V AC/DC
L
N
N
DO1
DO1
DO2
DO2
+
REF
_
N L
85..264 VAC
GND
Power
N
L
DO1
DO1
Note:
Power GND ≠ TX REF
Do not use shield as REF
-ETM, -ETB
Ethernet Connection
TCP/IP
-WEM, -WEB
WIFI Connection
TX3
-MOD
REF
BACnet MS/TP
TX1
TX2
-BAC
_
+
RS-485
_
REF
(D0)
(D1)
MODBUS
+
3 VA

TCI2
PRODUCT DATA SHEET
Doc: 70-07-0703B, 20220426 © Vector Controls LLC, USA Page 6-10
Subjects to alteration www.vectorcontrols.com
VECTOR
Type: TCI2-222.200
Configuration of in- and outputs
The inputs and outputs are configured with jumpers. Jumpers are located underneath the controller.
AO: Selection of analog output type
Left position:
voltage output (0... 10 V)
factory default
Right position:
current output (0... 20 mA)
AO1
UI: Selection of universal input type
Left position:
voltage output (0... 10 V)
factory default
Middle position: current input (0... 20 mA)
Right position: RT or dry contact
UI1
0…10V
0…20mA
0…10V
0…20mA
RT / DI
█
█
See the TCI2 installation sheet, document no. 70-00-0688 or 70-00-0893 (www.vectorcontrols.com).
Status-LED
The TCI2 has a status-LED which is located on the upper left side of the controller housing.
The location of the LED is described in the installation sheet. The function of the LED is explained in the X2 Operations Manual.
Rest button TCP/IP (-WEM, -WEB, -ETM, -ETB only)
The TCP/IP configuration setting of the TCI2 can be reset by pressing the reset button with a 1 mm pin through the small hole
located next to the Status-LED. The function of the TCP/IP reset is explained in the X2 Wi-Fi / Ethernet Configuration Manual.
OPT1-xx
OPA2-xx
N L
Operation
Terminal
GND
UI1
UI2
Digital Output (2x)
Power
Relays 3A
NTC Input (2x)
NTC 10k

UI3
UI4
VDC Input (2x)
0...10 VDC
Status LED
GND
UI
NTC
10k

UI
GND
0…10 VDC
UI
GND
GND
V+
24V AC/DC
3 VA
GND
Vop
+
_
STP
OPXX-VC
1
2
3
4
120
Ω
JP7
OP3
OP1
OP4
OP2
24V AC/DC
L
N
N
DO1
DO1
DO2
DO2
+
REF
_
UI1/2
UI3/4

TCI2
PRODUCT DATA SHEET
Doc: 70-07-0703B, 20220426 © Vector Controls LLC, USA Page 7-10
Subjects to alteration www.vectorcontrols.com
VECTOR
Operation and Configuration
Documentation
This controller uses the latest generation X2 operating system. Detailed operation instructions for all devices equipped with
this operating system can be found on our website.
Also available are programming instructions for technicians and an application database.
Configuration
The device can be fully configured and commissioned using the EasySet program.
EasySet may be downloaded free of charge from our website www.vectorcontrols.com.
Documentation overview
Document Type
Document No.
Description
TCI2 Data Sheet
70-07-0174
Product data sheet (this document)
TCI2 Install Sheet
70-00-0688
Mounting and installation manual -OP, -MOD, -BAC
TCI2 Install Sheet TCP/IP
70-00-0893
Mounting and installation manual -WEM, -WEB, -ETM, -ETB
X2 Operations Manual button display
70-07-0950
Operations instructions of X2 system with button display
X2 Web Interface operation manual
70-07-0952
Operations instructions of X2 Web interface
X2 Engineering Manual
70-07-0737
Guidelines for configuring the X2 system
X2 Modbus Communication Module
(-MOD type)
70-07-0290
Setup and configuration manual Modbus (no Modbus TCP)
X2 Modbus Communication Module
(-WEM, -ETM type)
70-07-0925
Setup and configuration manual Modbus TCP
X2 BACnet Communication Module
(-BAC type)
70-07-0218
Setup and configuration manual BACnet (no BACnet/IP)
X2 BACnet/IP Communication Module
(-WEB, -ETB type)
70-07-0899
Setup and configuration manual BACnet/IP
X2 Wi-Fi / Ethernet Communication
Manual
(-WEM, -WEB, -ETM, -ETB type)
70-07-0900
Setup and configuration manual TCP/IP
Note: The above list is not complete. The documents on the website are relevant.

TCI2
PRODUCT DATA SHEET
Doc: 70-07-0703B, 20220426 © Vector Controls LLC, USA Page 8-10
Subjects to alteration www.vectorcontrols.com
VECTOR
BACnet Protocol Implementation Conformance Statement (PICS)
BACnet MS/TP network
The following is only valid for products with the -BAC type option.
Vendor Name:
Vector Controls
Product Name:
TCI2 Controls series
TCI2 product description:
The TCI2 communicating BACnet controllers are designed as universal controls equipment
suitable for a large number of applications. They may be used in zoning and other applications
which are monitored by a BACnet MS/TP network.
Supported BACnet Interoperability Blocks (BIBB)
The BACnet interface conforms to the B-ASC device profile (BACnet Application Specific Controller).
The following BACnet Interoperability Building Blocks (BIBB) is supported.
BIBB
Type
Name
DS-RP-B
Data sharing
Read property - B
DS-RPM-B
Data sharing
Read property multiple - B
DS-WP-B
Data sharing
Write property - B
DM-DCC-B
Device management
Device communication Control - B
DM-DDB-B
Device management
Dynamic device binding - B
DM-DOB-B
Device management
Dynamic object binding - B
DM-TS-B
Device management
Time synchronisation - B
DM-UTC-B
Device management
UTC Time synchronisation - B
DM-RD-B
Device management
Reinitialize device - B
Supported standard BACnet application services
- ReadProperty
- ReadPropertyMultiple
- WriteProperty
- DeviceCommunication (password protected)
- I-Am
- I-Have
- TimeSynchronisation
- UTCTimeSynchronisation
- ReinitializeDevice (“cold” or “warm”) (password protected)
Supported standard Object types
- Device
- Analog input
- Analog value
- Binary value
- Multi-state Value
BACnet/IP communication
The following is only valid for products with the -WEB, -ETB type option.
Vendor Name:
Vector Controls
Product Name:
TCI2 Controls series
TCI2 product description:
The X2 communicating BACnet/IP controllers are designed as universal controls equipment
suitable for a large number of applications. They may be used in zoning and other applications
which are monitored by a BACnet/IP network.

TCI2
PRODUCT DATA SHEET
Doc: 70-07-0703B, 20220426 © Vector Controls LLC, USA Page 9-10
Subjects to alteration www.vectorcontrols.com
VECTOR
Supported BACnet Interoperability Blocks (BIBB)
The BACnet interface conforms to the B-ASC device profile (BACnet Application Specific Controller).
The following BACnet Interoperability Building Blocks (BIBB) is supported.
BIBB
Type
Name
DS-RP-B
Data sharing
Read property - B
DS-RPM-B
Data sharing
Read property multiple - B
DS-WP-B
Data sharing
Write property - B
DS-COV-B
Data sharing
Change of value - B
DM-DCC-B
Device management
Device communication Control - B
DM-DDB-B
Device management
Dynamic device binding - B
DM-DOB-B
Device management
Dynamic object binding - B
DM-TS-B
Device management
Time synchronisation - B
DM-UTC-B
Device management
UTC Time synchronisation - B
DM-RD-B
Device management
Reinitialize device - B
Supported standard BACnet application services
- ReadProperty
- ReadPropertyMultiple
- WriteProperty
- ChangeOfValue
- DeviceCommunication (password protected)
- I-Am
- I-Have
- TimeSynchronisation
- UTCTimeSynchronisation
- ReinitializeDevice (“cold” or “warm”) (password protected)
Supported standard Object types
- Device
- Analog input
- Analog value
- Binary value
- Multi-state Value
- Network Port
X2 Functional Scope
The controller has the following X2 functions and elements:
Group
Modules
QTY
Description
UP
User and display parameters
UI
01U to 04U
4
Universal inputs, selectable with jumper: RT/DI, mA, VDC
05U to 08U
4
Virtual inputs for operation terminals, bus modules or special functions
AL
1AL to 8AL
8
Alarm conditions
LP
1L to 2L
2
Control loops
AO
1A to 2A
2
Analog outputs, selectable with jumper: mA, VDC
FAN
1F
1
Fan or lead lag modules, 1 to 3 fan speeds, up to 3 switching lead-lag stages each
DO
1d to 2d
2
Binary outputs with a normally open (NO) relays contact
FU
1FU
1
Remote Enable: Activation of the controller based on signal and alarm conditions
2FU
1
Change Operation Mode: Switching occupied and unoccupied with control signals
3FU
1
Heat/Cool Change: Switching heating and cooling based on a control signal
4FU
1
Setpoint Compensation: Summer/winter compensation of setpoint
5FU
1
Economizer (free heating or cooling due to the condition of outside and room air)
CO
-
-
Communication (if a communication module is available)
COPY
-
-
Copying complete parameter sets between run, default and external memory with
up to 4 memory locations (AEC-PM2)
RTC
-
1
Real time clock module with 48-hour power back up (keeps clock running during
power failure)
PRO
Pr01 to Pr12
12
Time schedule programs for 7 days or annual switching events

TCI2
PRODUCT DATA SHEET
Doc: 70-07-0703B, 20220426 © Vector Controls LLC, USA Page 10-10
Subjects to alteration www.vectorcontrols.com
VECTOR
Smart Sensors and Controls
Made Easy!
Quality - Innovation –Partnership
Vector Controls LLC
USA
[email protected]
www.vectorcontrols.com