Vector 831.488540 User manual

Model No. 831.488540
User's Manual

Setup
1. Firmly press the thumb tab and pivot the
upright up until it locks in anearly verti-
cal position.
2. Insert the handles into the stem until the
lock pins are visible in the holes in the
stern.
3. Open the quick-release lever. Depress the
lock pin on the stem and slide the stem
up until the lock pin is visible in one of
the three holes in the upright. When the
stem is at the desired height, close the
quick-release lever so that it is snug
against the upright. If the quick-release is
not snug, see ADJUSTING THE
QUICK-_SE on the back of this
user's manual.
Before using the scooter, make sure that
the scooter is set up as described and that
all parts are securely tightened.
The decal shown at the right has been -
placed on the scooter. If the decal is miss-
ing, or if it is not legible, please call our
Customer Service Department toll-free at
1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time, to
order a free replacement decal. Apply the
replacement decal to the location shown.
To prevent
serious Injury:
•Read, understand
and follow all war-
nlngs and Instruc-
tions on the unit
and in the manual,
•Always wear pro-
tecllve equipment
Including helmet,
kneapads, wrlst
guards, and elbow
pads.
•Keep away from
cars, streets or
areas that enter
vehicle traffic
mutes.
•Never ride when
towed behind bi-
cycles, motorcy-
cles, or vehicles
•Do not ride at
night or In poor
visibility
Hand
Right Side
Storage
1. Openthequick-release lever. Depress the
lock pin on the stem and slide the stem
down into the upright. Close the quick-
release lever.
2Depress the lock pins and remove the
handles from the stem. Press the handles
into the storage clip on the upright.
3Pull the thumb tab and pivot the upright
down until it locks in the horizontal posi-
tion. Hand Brake, Carry Strap, and Cable not shown.

Part List/Exploded Drawing Model No. 831.4ui:i )4u R0700A
No. Qty. Description
11 Deck
2 1 Head Tube
3 1 Fork
4 1 Upright
51Stem
62 Handle
72Foam Pad
8 2 Handle Cap
9 3 Lock Pin
10 1 Handle Cord
11 1 Quick Release
12 1 Upright Clamp w/Ring
13 1 Bearing Nut
14 1 Bearing Cap
15 2 Bearing
16 2 Bearing Race
17 2 Bushing
18 1 Pivot Union Bolt Set
19 1 Front Union Bolt Set
20 2 Rear Union Bolt Set
21 2 Wheel
22 2 Rear Wheel Spacer
23 1 Brake Spring
24 1 Brake
25 1 Head Tube Spring
26 1 Storage Clip
27 2 Front Wheel Spacer
28 1Lock Pin
29 1 Deck Mount
30 1 Deck Cushion
31 1 Frame
32 4 Deck Screw
33 1 Cable Clip
34 2 Tek Screw
35 2 Brake Spacer
36 1 Mount Union Bolt Set
37 1 Hand Brake
38 1 Brake Bracket
39 1 Cable Bracket
40 1Brake Cable
41 2Flange Nut
42 1 Strap Clamp w/Ring
*1Carry Strap
* 1 User's Manual
*The user's manual and carry strap are not shown
Note: Specifications are subject to change without notice.
28
19
27
Ordering Replacement Parts
To order replacement parts, call toll-free 1-800-999-3756,
Monday through Friday, 6a.m. until 6 p.m. Mountain Time
(excluding holidays). When ordering parts, please mention
the model number (831.488540) and the number and
description of the parts needed.

If the quick-releasedoesn't hold the stem snug in place,
you will need to adjustit.
Open the quick-release lever. Turn the adjustment nut
clockwise one half turn while keeping the lever from turn-
ing. Close the lever. Repeat this procedure until the stem is
held snug in place.
If the quick-release is too snug to close, you will need to
adjust it.
While the quick-release lever is open, turn the adjustment
nut counterclockwise one quarter tern while keeping the
lever from turning. Close the lever. Repeat this procedure
until the stem is held snug in place and the quick-release is
closed.
Quick
Release
Adjustment
Nut
Close Open
Part No. 167662 R0700A Printed in China ©2000 ICON Health & Fitness, Inc.