Vega VEGADIS 61 User manual

Level
Switching
Pressure
Indication and Adjustment
Product Information
VEGADIS 61

2VEGADIS 61
2
7870-EN-021202

VEGADIS 61 3
2
7870-EN-021202
Contents
Contents
1 Product description .............................................................................. 4
1.1 Configuration ...................................................................................................... 4
1.2 Principle of operation .......................................................................................... 4
1.3 Adjustment ......................................................................................................... 4
2 Mounting .............................................................................................. 5
3 Connecting to the sensor ..................................................................... 6
3.1 Prepare connection ............................................................................................. 6
5.3 Wiring plans ....................................................................................................... 6
4 Set-up with the indicating and adjustment module PLICSCOM...........7
4.1 Adjustment system ............................................................................................ 7
4.2 Set-up procedure ................................................................................................ 7
Supplement ................................................................................................8
Technical data ............................................................................................................ 8
Dimensions ................................................................................................................. 9

4VEGADIS 61
2
7870-EN-021202
Product description
1 Product description
1.1 Configuration
Scope of delivery
The scope of delivery includes:
• VEGADIS 61 indication and adjustment unit
• Documentation
- operating instructions manual
- Ex specific safety instructions (for Ex ver-
sions) and other certificates, if required
Components
VEGADIS 61 consists of the following compo-
nents:
• mounting plate
• housing with electronics
• housing cover with indicating and adjustment
module PLICSCOM
The components are available in different ver-
sions.
1.2 Principle of operation
Area of application
VEGADIS 61 is an external indication and ad-
justment unit for the following VEGA sensors:
– Pressure transmitters VEGABAR 52, 53, 61, 64
and 65
- Level sensors VEGAFLEX 61, 62 and 65.
Fig. 1:
Example of VEGADIS 61 with plastic housing and
mounting plate for wall mounting
housing with
electronics
Housing cover with
indicating and adjust-
ment module
PLICSCOM located
below
Mounting plate
Fig. 2:
Connection of VEGADIS 61 to the sensor
Power supply
VEGADIS 61 is connected to the sensor via a
four-wire, screened standard cable with a
length of max. 25 m. An extra power supply is
not required.
1.3 Adjustment
VEGADIS 61 can be adjusted via two different
media:
• indicating and adjustment module PLICSCOM
• adjustment software PACT
ware
TM and PC.
The parameter adjustment is generally saved in
the sensor, or optionally in the PC when adjust-
ing with PACT
ware
TM and PC.

VEGADIS 61 5
2
7870-EN-021202
Mounting
2 Mounting
Select installation position
VEGADIS 61 functions in any installation posi-
tion. It is mounted either on a mounting plate or
rail 35 x 7.5 acc. to DIN EN 50 022. The housing
can be rotated 330° without using any tools.
Fig. 3:
Bore pattern for mounting on the mounting plate
85
62
7
12
Protection against moisture
Protect VEGADIS against moisture.
–>lead the connection cable located in front of
the cable entry downwards.
Fig. 4:
Measures against moisture ingress
Rain and condensed water can thus drain off,
especially in outdoor installations, in rooms
where humidity is expected (e.g. caused by
cleaning processes) or on cooled or heated
vessels.

6VEGADIS 61
2
7870-EN-021202
Connecting to the sensor
3.1 Prepare connection
Note safety instructions
Always observe the following safety instruc-
tions:
• Connect only in the complete absence of line
voltage
Note safety instructions of Ex applications
In hazardous areas, always observe the appro-
priate guidelines and type approval certificates
of the sensors and VEGADIS 61.
Select connection cable
VEGADIS 61 is connected with standard four-
wire cable to the sensor. An outer diameter of
5 … 9 mm ensures the seal effect of the cable
entry.
We recommend screened cable.
Select connection cable for Ex applications
In Ex applications, please observe the
appropriate installation guidelines.
3 Connecting to the sensor
5.3 Wiring plans
Top view of the electronics and connection
compartment
Display
Typ:
DS61
Com.
567 8
Contact spring for indicating and
adjustment module PLICSCOM
Earth terminal1)
Plug connection for
VEGACONNECT 3
with adapter cable
Spring terminal
for connection of
the sensor
1) Connect cable screen here, connect ground terminal on the
housing exterior to ground as prescribed. The two terminals
are galvanically connected.
2) Earthing at both ends in case of non-Ex. For Ex we recom-
mend earthing at one side acc. to EN 60079-14.
Display
5678
PC with PACT ware
TM
e.g. VEGABAR
Plug con-
nection
VEGADIS 61 VEGABAR/
VEGAFLEX
Terminal 5 –> Terminal 5
Terminal 6 –> Terminal 6
Terminal 7 –> Terminal 7
Terminal 8 –> Terminal 8
2)
Fig. 7:
Top view of the combined electronics and connection
compartment
Wiring plan
Fig. 8:
Wiring plan

VEGADIS 61 7
2
7870-EN-021202
Set-up with the indicating and adjustment module PLICSCOM
4 Set-up with the indicating and adjustment module PLICSCOM
4.1 Adjustment system
Indicating and adjustment elements
ESC OK
1.1
LC display for
indication of
- measured value
- menu item
- parameter
[ESC]
[+] [–>]
[OK]
Indication of
the menu items
[ESC]:
- Interrupt entry
- Jump to the next higher menu
[+]:
- Change the value of the parameter
[–>]:
- Menu
- Menu item
- Select parameter
[OK]:
- Jump to the menu range
- Confirm parameter
- Edit parameter
- Save the value
Adjustment system
You adjust the sensor via the four keys and the
display of the A/B module. The functions are
shown in the above illustration. 15. minutes after
you have pushed a key for the last time, an auto-
matic reset to the measured value will be trig-
gered.
4.2 Set-up procedure
The set-up and adjustment of the sensors must
be carried out according to the operating in-
structions of the sensor and the indicating and
adjustment module PLICSCOM.

8VEGADIS 61
2
7870-EN-021202
Supplement
Supplement
Technical data
General data
Instrument name VEGADIS 61
Materials
– housing plastic PBT (polybutylenterephtalat),
stainless steel 1.4435 (316L)
– inspection window in the housing cover plastic PC (polycarbonat)
– earth terminal stainless steel 1.4305
Weight 0.35 kg
Ambient conditions
Ambient temperature -20 … +70°C
Storage and transport temperature -40 … +85°C
Adjustment module PLICSCOM
Supply and data transfer with VEGADIS 61 via
sliding contacts (I²C-Bus)
Display LC-Display in Full-Dot-Matrix
Adjustment elements IP 20
Materials
– housing ABS
– inspection window Polyester foil
Electromechanical data
Cable entry 1 x M20 x 1.5 (cable-ø 5 … 9 mm)
spring-loaded terminal for conductor cross-section up to 2.5 mm²
Adjustment circuit
Connection to VEGABAR 52, 53, 61, 64, 65
VEGAFLEX 61, 62, 65
Data transmission digital (I²C-Bus)
Connection line 4-wire, screened
Cable length max. 25 m
Electrical protective measures
Protection IP 66/IP 67
Protection class II
Overvoltage category III
Approvals
ATEX II 1G, 2G EEx ia IIC T6

VEGADIS 61 9
2
7870-EN-021202
Supplement
Dimensions
VEGADIS 61
85
6
2
12
7
R7,5
M20x1
,5
M20x
1
6,
5
ca. 69
,5
117
ø
77
5

10 VEGADIS 61
2
7870-EN-021202
Supplement