Veilux VP-36X User manual

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
1
Website: www.Veilux.net Phone # [phone]

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
2
Website: www.Veilux.net Phone # [phone]
Copyright
ⓒ2010 Veilux.
Certification
Veilux provides the best products with the certifications below
Revision History
Date
Rev. No.
Description
2010-06
1.0
Creation of the document
2010-11
1.1
Image Change, Detailed Specification Change, Appendix

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
3
Website: www.Veilux.net Phone # [phone]
Warnings & Cautions
If you fail to read this information and handle the product incorrectly, faulty or malfunction as well as
death or serious injury may occur.
This Unit should be installed by trained
personnel.
Immediately stop using when the product
emits smoke or abnormal heat.
Never install the product in area exposed to
oil or gas.
Never install the product on a ceiling that
cannot hold its weight.
Never touch the power cord with wet hands.
Clean only with dry cloth.
Never use the product in extremely high or
low temperature condition.
Never drop, hit, strongly nor vibrate
the product.
Never expose the product to direct sunlight
or severe ray.
Never touch the front glass of the product.

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
4
Website: www.Veilux.net Phone # [phone]
Indications:
Warning: Death or Serious Injury will occur without following Warning.
Caution : Operational Problem(Faulty & Malfunction) will occur without complying with Caution
Reference : Technical Information for Users

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
5
Website: www.Veilux.net Phone # [phone]
Table of Contents
Table of Contents................................................................................ 5
1. Introduction................................................................................... 7
1.1. Overview of Veilux VP-36X........................................................................... 7
1.2. Specification .............................................................................................. 8
1.3. Application of Veilux VP-36X....................................................................... 10
2. Product Description....................................................................... 11
2.1. Contents................................................................................................. 11
2.2. Product Preview ....................................................................................... 11
2.3. Physical Description.................................................................................. 12
2.3.2. Internal Structure.................................................................................... 13
2.3.3. Dimension ............................................................................................ 14
2.4. Functional Description ............................................................................... 14
3. On Site Installation........................................................................ 17
3.1. Ceiling Mount........................................................................................... 17
3.1. Wall Mount .............................................................................................. 19
4. Getting Started............................................................................. 21
4.1. System Requirements ............................................................................... 21
4.2. Quick Installation Guide ............................................................................. 22
5. Trouble Shooting.......................................................................... 27
5.1. No Video on Viewer................................................................................... 27
5.2. Windows vista & Windows 7 User................................................................ 28
5.3 Technical Inquiry........................................................................................ 31
Appendix. DIP Switch Configuration...................................................... 32
Appendix. Quick Operating Keys .................................................... 36

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
6
Website: www.Veilux.net Phone # [phone]
Appendix. OSD Menu setting.......................................................... 38

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
7
Website: www.Veilux.net Phone # [phone]
1. Introduction
1
1. .1 1. . O Ov ve er rv vi ie ew w o of f V Ve ei il lu ux x V VP P- -3 36 6X X
Veilux VP-36X, as a state-of-the-art Professional Network Camera based on integrated Embedded Software
technologies such as H.264 & MJPEG, G.726 & PCM Video & Audio Compression, Embedded Web Server,
Embedded Streaming Server, various Network Protocols, transmits synchronized video and audio data in real
time with D1 resolution at full frame rate through IP Network as well as supports bi-directional audio
communication by allowing transmission of audio from Client PC to Veilux VP-36X.
Veilux VP-36X, with completed Integration with analog CCTV camera, Digital and network technology, is
applicable for various sectors such as Security, Remote Monitoring, Remote Education, Simple Video
Conference as well as Internet Broadcasting System etc.
Vandal proof housing satisfying IP-68 and fan/heater will extend the application area to harsh environment of
wide temperature range.

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
8
Website: www.Veilux.net Phone # [phone]
1
1. .2 2. . S Sp pe ec ci if fi ic ca at ti io on n
Category
Details
Video
Compression
H.264 / MJPEG
Resolution
D1, Half-D1, CIF, QCIF
Audio
(Bi-directional)
Up Stream
32 Kbps G.726
Down Stream
64 Kbps PCM
Network
Interface
RJ-45, 10/100 Mbps
Access Network
Static, DHCP, PPP/PPPoE
Protocol
IPv4/6, TCP, UDP, IGMP, ICMP, ICMPv6 etc.
I/O
Sensor
4
NC, NO Selectable
Relay Output
2
Alarm or Remote ON/OFF Control (30V, 1A)
RS-232C
For Factory Use Only
Mic/Line In
Selectable on Admin Page
Line Out
1 V p-p Audio Output for Amplified Speaker
CVBS Output
Supported
Power Supply
PoE
Not Supported
AC In
24VAC Adaptor (Higher than 1.5 Amp )
Housing
Water-Proof
IP68 Compliant Vandal Proof housing
Heater
Refer to Installation Circumstance
Installation Type
Bracket
Wall Mount Type, Ceiling Mount Type
Motion Detection
3 Zones
Optional Shape & Sensitivity for 3 Regions
Upgrade
Remote F/W Upgrade via IP Network
Management & Configuration
Remote Management & Configuration via IP Network and
Admin Tool Page
Client
/
Viewer
Web Viewer
Simple Access via Internet Explorer
NVR-Pro
CMS Software
3rd Party CMS
Contact to Veilux
Dynamic IP
DDNS support
Supported by Veilux Management Server
Security Management
User ID & Password Protection, IP Filtering, Audio per user
and Bi-directional audio communication configuration
control
Time
Configuration
Sync to PC
Sync to PC Time
Manual
Manual Configuration

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
9
Website: www.Veilux.net Phone # [phone]
Management
Internet Time Server
Sync to Time Server
DLS
Summer Time Configuration
PAN/TILT
PAN Rotation Angle
0˚ ~ 360˚ Endless
PAN
Rotation
Speed
Manual
1˚ ~ 100˚/Sec (64step)
Preset
Max. 200˚ /Sec, Min 10˚ /Sec
TILT Rotation Angle
0˚ ~ 360˚ Endless
TILT Speed
Manual
1˚ ~ 100˚/Sec (64step)
Preset
Max. 150˚ /Sec, Min 7˚ /Sec
Minimum Rotational
Resolution
0.024˚
Functions
Preset
-165 Positions identifiable with 16 character label available for each
position with different seed steps and Freeze Preset available.
Group Tour
Max. 8 Programmable Group Tours
(Max. 60 different Presets Steps for each Group Tour)
Auto Scan
Programmable Auto Scan
Pattern
8 Programmable Patterns (total 480 seconds)
Privacy Zone
24
Sector
8 Selectable Sectors with 16 characters
Password Protection
Available
Alarm Input
4 (NC/NO Selectable)
Alarm Actions
On Alarm Input, trigger Preset, Group Scan or Relay Output
Aux Output
2 Relay Output
Auto Flip
No
OSD Menu
Yes (English, Italian, Polish)
Communication
RS-485
Power
Power Consumption
AC24V : Max 48W (2.0A with Heater)
Power Supply
AC 20~32V, 60/50Hz 2.5A
Camera
Module
Image Sensor
1/4" Super Ex-view HAD CCD
No. of Pixels
NTSC
811 (H) * 508 (V) 410K
PAL
795 (H) * 596 (V) 470K
No. of
Effective
Pixels
NTSC
811 (H) * 508 (V) 410K
PAL
795 (H) * 596 (V) 470K

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
10
Website: www.Veilux.net Phone # [phone]
Horizontal Resolution
550 TVL
ZOOM
Optical
36x Optical Zoom (F1.6~4.5, f=3.4~122.4mm)
Digital
12x ( 432x including Optical Zoom)
Day/Night(ICR)
Auto / Day / Night
Digital Slow Shutter
2/4/8/16/24/32/64/128/ OFF
Min.
Illumination
Normal
Mode
0.1 Lux (50IRE)
Night
Mode
0.01 Lux (ICR On)
Luminance S/N Ratio
Higher than 50dB
Video Output
VBS :1.0Vp-p (sync negative), 75 ohm
BLC
ON / OFF
Flicker less
NTSC
ON / OFF (1/100)
PAL
ON / OFF (1/120)
1
1. .3 3. . A Ap pp pl li ic ca at ti io on n o of f V Ve ei il lu ux x V VP P- -3 36 6X X
- Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government
facilities, military, etc.)
- Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)
- Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting
- Weather and Environmental Observation

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
11
Website: www.Veilux.net Phone # [phone]
2. Product Description
2
2. .1 1. . C Co on nt te en nt ts s
The product package contains followings;
Contents
Description
Remarks
Veilux VP-36X
Veilux VP-36X Main Unit
Power Adaptor
24V AC Adaptor
CD
Software & User’s Guide
Quick Reference
Quick Installation Guide
2
2. .2 2. . P Pr ro od du uc ct t P Pr re ev vi ie ew w
Veilux VP-36X
IP-Installer
CMS Software
(NVXR-64)
H.264 Professional Speed
Dome Network Camera
IPAssignment Program
PC based Client for
monitoring/storing Video/Audio
transmitted form Veilux VP-36X
(Max. 16CH supported)

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
12
Website: www.Veilux.net Phone # [phone]
2
2. .3 3. . P Ph hy ys si ic ca al l D De es sc cr ri ip pt ti io on n
2.3.1. External View
Figure 2-1. External View of Veilux VP-36X

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
13
Website: www.Veilux.net Phone # [phone]
2
2. .3 3. .2 2. . I In nt te er rn na al l S St tr ru uc ct tu ur re e
Figure 2-2. Cabling Description

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
14
Website: www.Veilux.net Phone # [phone]
2
2. .3 3. .3 3. . D Di im me en ns si io on n
2
2. .4 4. . F Fu un nc ct ti io on na al l D De es sc cr ri ip pt ti io on n
AC Power
Power Input for supplying 24V AC, 1.5A.
MIC/LINE IN
Connect external Audio Device or Microphone.
Line Out
Connect speakers with built in amplifier. Audio from remote site is output through Line out in bi-directional
audio mode.

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
15
Website: www.Veilux.net Phone # [phone]
100Base-T
100Mbps Ethernet connector (RJ-45). 2 LEDs on the Ethernet connector shows the status of Veilux VP-
36X as the followings:
-Status LED (Dual Color - Red/Green) : It will be lit in green or red depending on the status.
Green : Green color indicates that the camera is in normal operation mode. Continuous green
indicates that data transmission is possible. Blinking green means that someone is
connected to Veilux VP-36X.
Red : Continuous or blinking red indicates that hardware is in abnormal condition.
Red/Green LED will be lit with red momentarily and it will be lit with green after a while when
power is applied into Veilux VP-36X
-LINK/LAN LED (Orange)
It will be lit with orange color when network cabling is all right. Blinking orange color indicates that
normal data transmission is under way. Off state indicates that there is trouble in network connection.
RLY Out (AUX 1, 2)
Relay output is provided for connecting alarm devices or for remote on/off control of devices such as light.
Relay is normal open and it will be closed upon alarm annunciation or remote on. The relay is capable
of switching 30V AC/DC, 2A. For the application which needs power switching beyond this limit, use
additional relay switch as shown in the right of Figure 2-3.
Figure 2-3. Relay Connection Diagram(Left : Lower than 30V, 2A, Right : Higher than 30V, 2A)
SENSOR IN (Alarm 1,2,3,4)
Connect external alarm sensor. Examples of sensing devices are infrared sensor, motion sensor,
heat/smoke sensor, magnetic sensor, etc. Connect the two wires of the sensors to “SNS In”. The

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
16
Website: www.Veilux.net Phone # [phone]
sensor type(NC/NO) can be set in admin page. 10 mA can be flown into sensor device. Multiple sensor
devices can be connected in parallel.
Sensor
Device
Sensor
Power
Supply
NO/NCType
Sensor1-
Sensor1+
+12V GND
Sensor
Device
Sensor
Power
Supply
Open CollectorType
Photo Coupler
Figure 2-4. Sensor Input Connection Diagram

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
17
Website: www.Veilux.net Phone # [phone]
3. On Site Installation
3.1. Ceiling Mount
1. When you install IR PTZ Camera on the ceiling, make 4 holes at the edge with Ø13 in diameter and 37mm in
depth. If you want to connect the cables from the inside of the ceiling, also make a hole for the cables with
about Ø30~50 in diameter in the center of 4 edges.
Figure 3-1. Hole Position & Size
2. Connect the Ceiling Mount Bracket to the Camera with 4 pieces of M4X15 screws and spring washer.
3. Connect the Safety wire of the Camera to the Bracket. In order to avoid getting entangled in the Camera,
fasten the Safety wire to the bracket with Cable tie.
Figure 3-2. Connection of Camera & Bracket
SCREW
(M4*15 4EA)
SPRING
WASHER
(∮4 4EA)
CABLE TIE
SAFETY WIRE

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
18
Website: www.Veilux.net Phone # [phone]
4. When you want to connect the cables from the inside of ceiling, pass the cables through the ceiling. When
you want to connect the cables from the outside of ceiling, remove the hole cap from the side of the bracket and
pass the cables through the hole.
Figure 3-3. Ceiling Mount
5. Install 4 pieces of Anchor bolt in the holes at the edge and tight enough with NUTs.

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
19
Website: www.Veilux.net Phone # [phone]
3.1. Wall Mount
1. When you install IR PTZ Camera on the wall, make 4 holes at the edge with Ø13 in diameter and
37mm in depth and install 4 pieces of Anchor bolt in the Ø13 holes at the edge.
Figure 3-4. Hole Position & Size
2. Connect the Camera to Wall Mount Bracket with 4 pieces of M4*15 screws and Spring Washer.
Figure 3-5. Connection of Camera & Bracket
3. Connect the Safety wire of the Camera to the Bracket. In order to avoid getting entangled in the Camera,
fasten the Safety wire to the bracket with Cable tie.
Install the Veilux VP-36X at the high place out of hands in order to protect the product safely.
Wall

V
Ve ei il lu ux x V VP P- -3 36 6X X U Us se er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov. 2010)
20
Website: www.Veilux.net Phone # [phone]
Figure 3-6. Wall Mount
4. With Wall Mount Installation, Connection in the Bracket through Wall and Connection out of the Bracket on
the Wall are available. Refer to Figure3-6.
5. Install 4 pieces of Anchor bolt in the holes at the edge and tight enough with NUTs.