Veilux VVIP-2V User manual

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVER. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of un-insulated "dangerous voltage" within the
product’s enclosure that
may be of sufficient magnitude to
constitute arisk of electric shock.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature
accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF THE PLUG TO THE WIDE SLOT AND FULLY INSERT.
VVIP-2V, VVIP-3V, VVIP-5V
User Manual
www.veilux.net

Important Safeguards
In addition to the careful attention devoted to quality standards in the manufacturing process of
your
video product, safety is amajor factor in the design of every instrument. However, safety is
your responsibility too. This sheet lists important information that will help to assure your
enjoyment and proper use of the
video product and accessory equipment. Please read them
carefully before operating and using your
video product.
Ins t allation
1. Read and Follow Instructions - All the safety and
operating instructions should be
r ead befo r e the
video product is operated. F o ll o w all op er ating
ins
tr uctions.
2.
Retain Instructions - The safety and operating
instructions should be retained for future
r e f e r ence.
3.
Heed Warnings - Comply with all warnings on the
video product and in the operating ins tru ctions .
4.
Polarization - Do not defeat the
safety purpose of the polarized
or
grounding-type plug.
Apolarized plug has two blades
with one wider than the
o t h e r.
Agrounding type plug has two
blades
and athird grounding prong.
The wide blade or the third prong
are provided for
you r safety.
If the provided plug does not fit into
you r outlet,
consult an electrician for replacement of the
obsolete outlet.
5.
Power So u r c e s - This video product should be
ope r at ed only from the type of po w e r sour ce
indicated on the marking label. If you are not sure of
the type of power supply to your
l oc a tion, co nsult
your video dealer or l oc a l power company. For video
products intended to operate from battery power,
or
other sources, refer to the operating ins tru ctions .
6.
Overloading - Do not overload wall outlets o f
extension cords as this can result in the risk of fire
or electric shock. Overloaded AC outlets, extension
cords,
f r ay ed po w e r cords, damaged or c r a c k ed w i re
insulation, and broken plugs are dange r ous. They
may
result in a shock or fire hazard. P e r i od i c a ll y
examine the co r d , and if its appearance indic a t es
damage or deteriorated insulation, have it r e plac ed
by your service t e chnician.
7.
Power Cord Protection - Power supply cords should
be routed so that they are not
lik e l y to be walked on
or pinched by i t em s placed upon or against them ,
paying particular attention to cords at plugs,
convenience r ecep t ac l es, and the point where they
exit from the
video pr oduct.
8.
Ventilation - Slots and openings in the case ar e
provided for ventilation to ensure reliable oper a t ion
of the
video product and to protect it fr om
overheating.
These openings must not be blocked or
covered. The openings should never be blocked by
placing the
video equipment on abed, sofa, rug, or
other similar surface. This video product should
ne v e r be placed near or over aradiator or heat
register.
This video product should not be placed in a
built-in installation such as a
bookcase or r a ck
un
l ess proper ventilation is provided or the video
product manufacturer’s instructions
have been
fo
ll o w ed.
9. Attachments - Do not use attachments unl ess
r eco mm ended by the video product manufacturer as
they may
cause a h aza r d.
10.
Camera Extension Cables – Check the rating of
your extension
cable(s) to verify compliance with
your
l oc a l authority regulations prior to in s t all a tion .
11. Water
and Moisture - Do not use this video pr oduct
near water. For example, near abath tub, wash
bowl, kitchen sink or laundry tub, in a w
e t
basement, near aswimming pool and the lik e.
Caution: Maintain electrical safety.
Po we rline
ope r ated equipment or accessories connected to
this unit should bear the UL listing mark of CSA
certification mark on the
accessory itself and shou ld
not be modified so as to defeat the safety fea tures.
This
will help avoid any potential hazard from
electrical shock or fire. If in doubt, contact qualified
service personnel.
12.
A ccess o r ie s - Do not place th is
video equipment on an unstabl e
cart, stand, tripod, or table. The
video equipment may fall, causing
serious
damage to the video
product. Use this
video pr oduct
only with a cart, stand,
t r ipod,
bracket, or table r eco mm ended by t h e
manufacturer or sold with the video product. Any
mounting of the product should
f o ll o wthe
manufacturer’s instructions and use amounting
accessory r eco mmended by the manufactur er .
Precautions
Service
13. Servicing - Do not attempt to service this video
equipment yourself as opening
or r e m oving co v e r s
may expose you to dangerous voltage or other
hazards.
Refe r all servicing to qualified service
pe r sonne l.
14.
Conditions Requiring Service - Unplug this video
product from the
wa ll outlet and refer servicing to
qu a l ified service personnel under the f o ll owing
cond itions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled or objects have f a ll en int o
the video pr oduct.
• If the video product has been exposed to rain or
water .
• If the video product does not operate normally by
f o ll owin g the operating instructions. Adjust only
those controls that are covered by the operatin
g
instructions. Improper adjustm ent of other co ntr ols
may
result in damage and will often r e quir e
extensive
work by a q u a l ified technician to r es t or e
the video product to its normal operation .
• If the video product has been dropped or the cabinet
has been damaged.
• When the video product exhibits a distinct change
in performance. This indicates aneed
for service.
15.
Replacement Parts - When replacement parts ar e
required, have the service technician verify that the
replacements used
have the same safety
characteristics as the original parts. Use of
replacements specified by the
video pr oduct
manufacturer can prevent fire,
e l ec tric shock o r
other hazards.
16.
Safety Check - Upon completion of any service or
repairs to this video product, ask the service
technician to perform safety checks
r eco mme nded
by the manufacturer to determine that the video
product is in safe operating
co ndition.
17. Wall or
Ceiling Mounting - The cameras provided
should be mounted to a w
a ll or ceiling o n l y as
instructed in this guide, using the provided
mounting
br acke ts.
18. Heat
- The product should be situated away fr om
heat sources such as radiators, heat
r e gis ter s,
stoves,
or other products (including amplifiers) that
p r oduce heat.
Use
19. Cleaning - Unplug the video product from the wall
outlet be f o r e cleaning. Do not use l i quid c l e a ne r s or
ae r oso l cleaners. Use adamp cloth for c l e a ning.
20.
Product and Cart Combination - Video and c a rt
combination should be moved with c a r e. Quick
stops,
excessive force, and uneven surfaces may
cause the
video product and cart combination t o
o
v e rturn.
21.
Object and Liquid Entry - Never push objects of any
kind into this
video product through openings as
they may touch dangerous voltage points
or
“short-out”
parts that could result in a fire or
e l ec tric shock. Never spill liquid of any kind on the
video p r oduc t.
22.
Lightning - For added protection for this video
product during alightning storm, or when it is
l e ft
unattended and unused for l ong periods of time,
unplug it
from the wall outlet and disconnect the
antenna
or c a b l e system. This will p r e v e n t damage
to the
video product due to lightning and power line
su
r ges.

General Precautions
1. All warnings and instructions in this manual should be f o ll owed.
2.
Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use a
water
dampened cloth for cleaning.
3.
Keep enough space around the unit for ventilation. Slots and openings in the s t o r age cabinet
should not be blocked.
4. During lightning storms, or when the unit is not used for a
l ong time, disconnect the po wer
supply, antenna, and cables to protect the unit from electrical
sur ge.
FCC CLASS A NOTICE
NOTE
This equipment has been tested and found to comply with the limits for aClass Adigital device pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
ha rmful
interference when the equipm ent is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the manu
facturer’ s
instruction manual, may cause harmful interference with radio communications. Operation of this eq uipment
in aresidentia
l a r ea is likely to cause harmful interference, in which case you will be required to correct th e
interference at your own expense.
This equipment has been certified and found to comply with the limits regulated by FCC, EMC, and
LVD. Therefore, it is designated to provide reasonable protection against interference and will not
cause interference with other appliance usage.
However, it is imperative that the user follows the guidelines in this manual to avoid improper
usage which may result in damage to the unit, electrical shock and fire hazard injury.
In order to improve the feature functions
and quality of this product, the specifications are subje ct
to change without notice from time to time.
Features
• HD CMOS Progressive Scan
• 720p or 1080p models with real-time (25/30 fps)
• 3Mega Pixel 2048x1536 or 5 Mega Pixel 2592x1920 Models
• Triple-streaming (H.264/MJPEG)
• Future proof ONVIF 2.1 compliance (1.02 backwards c o mpatibl e)
• Compatible with popular third party VMS softwar e*
• Power-over-Ethernet (PoE) operation, 14Watt max/12V operation
• Backup options: micro SD c a r d ,FTP, NAS, l o c a l
• Mobile Apps: iPhone®, iPad®, Android™
• Supports two-way audio
• 2.8-12mm V a rif oc al MegaPixel l e ns
• 65ft (20m) IR Night Vision, T r ue Day/Night (TDN)
• IP66 Weatherproof and IK10 Vandal Resistant
• Multi-browser support: IE, Firefox, Safari, Chrome
• 3Axis Design for wall/ceiling mount

TABLE OF CONTENTS
1. Getting Started ....................................... 1
1.1 Default Camera Username, Password, and Ports ............... 1
1.2
Camera Interior Overview .................................. 2
1.3ONVIF Compatibility and Included Software Overview ............ 3
1.3.1 NVMS .............. . . ................................................. 3
1.3.2 CD Contents
....... . . . . . . . . .............................................. 3
2. Connection .......................................... 4
3.
Camera Installation ................................... 5
4.
Junction Box Plate ................................... 10
4.1 Junction Box Plate Dimensions and Fitting ................... 10
5. Junction Box Installation Types ........................ 11
5.1 Two Gang Fitting (Recommended) ........................... 11
5.2 4S Fitting ............................................... 11
5.3 Octagon
Fitting .......................................... 11
6. Finding the Camera’s IP Address ...................... 12
6.1 Finding the Camera’s IP Address Using NVMS . . . . ............ 12
6.2
Finding the Camera’s IP Address using UPnP in Windows® 7.... 13
6.3
Finding the Camera’s IP Address using Bonjour® in Mac OS® ... 14
6.4
Finding the Camera IP using the BNC Test Cable .............. 15
7. Configuring Remote Connection ....................... 16
7.1 Connecting to a DDNS address using NVMS ................ 19
8. Web Configuration ................................... 21
8.1 Supported Browsers ...................................... 21
8.2
Chrome, Firefox, and Safari Setup .......................... 21
8.3
Internet Explorer® Setup .................................. 22
8.4 Web
Interface/Live Video Overview.......................... 25
8.4.1 Live Video Menu ....................................................... 25
8.4.2
Configuring Camera Settings ............................................ 26
8.5 Device Info .............................................. 27
8.6
Stream Configuration ..................................... 28
8.7 Device
Configuration ...................................... 29
8.7.1 Local Network ......................................................... 30
8.7.2 Device Port ........................................................... . 31
8.7.3
Camera .............................................................. . 32
8.7.4
Date &Time .......................................................... . 32
8.7.5
OSD ................................................................ . 34
8.7.6
Microphone .......................................................... . 35
8.7.7 BNC Video
Output ..................................................... . 36
8.7.8
Language ............................................................ . 36
8.8 Alarm Configuration ...................................... 37
8.8.1 Disk Alarm ........................................................... . 37
8.8.2
Motion Alarm ......................................................... . 38
8.9 Local Record ............................................ 40
8.9.1 Record Directory ...................................................... . 40
8.9.2
Record Policy ......................................................... . 45
8.10 Privacy Masking ........................................ 47
8.11
Network Service ........................................ 48
8.11.1 DDNS .............................................................. . 48
8.12 Service Center .......................................... 49
8.12.1 SMTP (Email Alert Setup) .............................................. . 49
8.13 Privilege Manager ....................................... 50
8.13.1 Group .............................................................. . 51
8.13.2
User ............................................................... . 52
8.13.3
Unlocking User Accounts .............................................. . 53
8.14 Protocol ............................................... 54
8.14.1 Protocol ............................................................ . 54
8.15 Device Restart .......................................... 54
8.16
Default Settings ......................................... 55
8.17
Sensor Configuration .................................... 55
8.17.1 Image Adjust ........................................................ . 56
8.17.2
Shutter Control ...................................................... . 56
8.17.3 Gain
Mode ........................................................... . 57
8.17.4
Day/Night Mode ...................................................... . 57
8.17.5
Auto Iris ............................................................ . 58
8.17.6
Gamma ............................................................. . 58
8.17.7 AE
Meter Mode ....................................................... . 59
8.17.8
WDR ...............................................................59
8.17.9 WB Setting .......................................................... . 60
8.17.10
Mirror ............................................................. . 61
8.17.11
Noise Filter ......................................................... . 61
9. Resetting to Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . 62
10.
Dimensions ........................................64
11.
Troubleshooting .................................... 65

1 2
1. GETTING STARTED
The system comes with the following
components:
• 1 x Camera
• 6 x Camera locking screws (3x inside
camera; 3x spare)
• 1 x Surface mounting template
• 1 x Junction box plate and screw kit
• 1 x Mounting screw kit
• 1 x Allen key
• 1 x Conduit key
• 1 x RJ45 coupler
Mounting Screw Kit:
• 3 x 2.8in / 70mm screws
• 3 x 1.2in / 30mm screws
• 3 x 1.6in / 40mm anchors
• 1 x BNC test cable
• 1 x Instruction Manual
• 1 x Quick Start Guide
• 1 x Software/Documentation CD
1.1 Default Camera Username,
Password, and Ports
Username: admin
Password: admin
Junction
Box Plate
Allen Ke y
BNC Test Cabl e
Conduit Key
RJ45 Coupler
Ports: 80
(HTTP), 30001 (Control/Streaming), 8080 (RTMP), 554 (RTSP)
IP Address:
DHCP Enabled by Default (Router will automatically assign IP
address)
NOTE: Once you have completed the basic setup of the camera, it is
r e c o mmended t o configure a static IP addr es s. This will pr ev ent the c a mer a
IP address changing in the event of apower failure. For details, see “8.7.1
Local Network” on page 30.
1.2 Camera Interior Overview
Front of Camera
IR
LED’s
Camera Lens
Zoom
Focus
CdS Sensor
Rear of
Camer a
BNC analog
output
Reset button
Termination cables
microSD card
slot
(max.
64GB supported;
SanDisk™/Kingston™ brand
memory cards recommended)

3 4
1.3 ONVIF Compatibility and Included Software Overview
This camera is ONVIF v2.1 compliant. It is designed for interoperability with
popular VMS’s and NVR’s*, with backwards compatibility to ONVIF v.1.02. For
more information on
ONVIF, visit www .onvif .or g
NOTE: Provided software is PC compatible only; Mac OS® access to the
cameras is available via Safari® browser only.
1.3.1 Veilux VMS
•
Veilux VMS is a client-only solution that supports up to 36 IP
cameras. Veilux VMS is a free software provided on the CD.
•
Veilux VMS supports all the features of the camera. It can access microSD/ SD
card recordings and camera setup over alocal network.
•
Veilux VMS manual is provided on the CD.
1.3.2 CD Tools
• CD contents Folders
IP Search ; Search find IP Cameras and set IP address and gateway
NTP Service Tool ; Time Sync Application:IP devices match one PC system time.
FTPUpdater ; Firmware Update tool
IP Support Help Files ; Website support help documents for common problems.
RTSP Tool ; provides RTSP string command f. e.g VLC or Quick-time use
SD Driver ; Ext2 driver for Windows XP to read sd Memory card on PC
Onvif_Help ; documents on Onvif specifications
Open the NTP service ;Windows XP only enables NTP time to be enabled.
Adobe Flash Player ; Flash Video player for Windows IE plugin and Apple Mac OS
Adobe AcrobatReader ; Windows and Max OS Acrobat Reader v10
Files:
IP_series_bitrate_calculator.htm ; Simple storage calculator for IP devices
Veilux VMS_Install.exe ; NVR Software installation for PC
Veilux VMS_Manual_1.7.pdf ;Guide to use the Veilux VMS Software
SNMedia_Player.exe ; File Player for recorded files / backup files from devices /
Veilux VMS.
Connection
2. CONNECTION
The camera has the following termination cables:
1.
RJ45 Network Interface: Connect to a router or switch on your network
using
RJ45 Ethernet cable (Cat5e or better). 100Mhz connection. PoE
supported (class 3 PoE switch r e quir ed).
NOTE: Use the included RJ45 coupler to connect to male end of R J 45
Ethernet cable.
RJ45 Coupl er
2. Audio Input (RCA): Connect to a self-powered microphone for lis t en-in
audio.
3.
Audio Output (RCA): Connect to an amplifier or self-powered speaker f o r
intercom/2-way audio.
4.
DC12V (1A): 12V DC power input terminal. Make sure to f o ll ow c o rr ect
polarity (+/-) marked on the power connector when connecting to power.
• Minimum Power Requirement: 550mA / 6.6W.

5 6
3. CAMERA INSTALLATION
Make sure to follow the correct polarity if connecting
the camera to
DC power. Polarity is marked on the
power connector.
All
Installation Methods
11.Loosen the three tamper
scr ews
using the provided allen key. Lift the
dome
c o v e r .
NOTE: If you plan to use conduit fitting,
r e mo v e conduit cap using the provided
conduit key.
All
en
Ke
y
Conduit
Key
Mounting
Template
Method 1 - Direct Attach Install
2a 2a.
Use the included mounting
te
m p l a te ( In s ta ll a t i o n Option 2) to m a r k
and pre-drill the required holes.
Remove 2of the 3 base locking screws.
Use 2pc of the 2.8” screws to mount the
camera directly to the mounting
surface.
Remove the 3rd base locking screw and
install the 3rd 2.8” screw.
Go to step 4to complete installation.
Method 2 - Camera Base Install
2b. Use the included mounting template (Installation Option 1) to mark and
pre-drill the required holes.
2c/2f
2d
2g
2c. Remove the c a mer a
base
by unscrewing the 3
base l o cking screws, and
turn camera modul
e
approx. 5degrees
counterclockwise to detach
camera
base from the
camera modul
e.
2d. Ins t a ll the base to the
correct holes as indicat ed
on the mount t e mplat e
using the 1.2” scr ews.
Go to step 3a to complete
installation.
Method 3 - Junction Box
Install
2e. Attach provided
fitting
plate to junction box (see “5.
Junction Box Ins t allation
Types” on page 11).
2f.
Remove the c a mer a
base
by unscrewing the 3
base l o cking screws, and
turn the camera modul
e
approx. 5degrees
counterclockwise to detach
camera
base from c a mer a
modul e.
2g. Install the base to the
junction box plate using the
base fitting scr e ws.
Go to step 3a to complete
installation.

7 8
3a
3b
4
5
Test cable
terminals
Reattaching the Camera Module
3a. Reinsert camera module
int o
camera base by aligning the arr ow
notches on the edge of the c a mer a
module and the camera base
(label on
edge of camera modul e
indicates the l o c a tion of the arr o w
notch), and turning
c a mer a
modul e clockwise to l o ck int o
place.
3b. Use the 3 base l o cking scr e ws
to secure camera base to c a mer a
modul e.
Go to step 4to complete
installation.
4. Remove camera c o v e r by
squeezing the back and front of
the
c o v e r (as indicated by the
arrow indicators) at the same
time and lifting it up and away
from the
l e ns.
5.Insert a video test cable into
the
video test cable t e rminals
and connect to a test monitor t o
set up c a mer a.
Video Test Cabl e
6a
Thumb Screw
6b
6c
microSD card
6a. Adjust camera viewing angle and secure
int o
place by tightening thumb screw using aflat head
scr e wdriv er .
Avoid
pointing the camera lens in
angles where the IR LEDs are
blocked
by the camera cover or dome
cover. If IR
LEDs are blocked, it may
result in an unclear nighttime image.
6b. Adjust zoom and focus as r e quir ed.
NOTE: Lens adjustment l e v e r s are by def ault
in the l o ck ed position. Turn c o unter cl ockwise
to unlock. Tighten l e v e r s to secure l e ns
setting.
6c. (Optional) Insert amicroSD card into the
camera.
To enable recording, you mus t
format the microSD card and c o nfigur e
microSD recording (see “8.9.1 Record
Directory” on
page 43).
NOTE: The camera supports microSD c a r ds
up to a maximum size of 64GB. SanDisk™ or
Kingston™ brand microSD c a r ds ar e
r e c o mmended.
6d. Re-attach the camera cover, using the
thumb screw as aguide, until it snaps int o
place.

9 10
7
Arrow on camera base
Arrow on camera
7.Re-attach the
dome
c o v e r .
Align the arrows
as shown in the
diagram to
ensure a
waterproof seal.
Use the allen key
to tighten
t h e
tamper sc r e w s .
module (inside camera)
NOTE: Mak e sur e
dome cove r co r d
Correct Arrow Alignment
Arrow on dome cover
does not get
caught in the
rubber seal.
Junction
4. JUNCTION BOX PLATE
Junction box plate is used to install camera into standard 4S and Octagon
junction
boxes. Junction box plate screw kit contains the following
accessories:
• 3 x Base fitting screws (PWM3 Type)
• 4 x 2S / 4S plate screws (KM3.5 Type)
• 2 x Octagon fitting screws (KM4 Type)
Base Fitting Screw
Octagon Screw
2S / 4S Screw
4.1 Junction Box Plate Dimensions and Fitting

11 12
Junction Box InstallationTypes
5. JUNCTION BOX INSTALLATION TYPES
5.1 Two Gang Fitting
(Recommended)
Two gang fitting requires 4x 2S/4S screws.
NOTE: Two gang fitting provides the mos t
robust ins t a llation.
5.2 4S Fitting
4S fitting requires 2x 2S/4S screws.
Screws
Screws
5.3 Octagon Fitting
A4" Octagon fitting requires 2x Octagon
screws.
NOTE: Screws used for the octagon fitting
are larger compared to those used for the
2S/4S (M4 type).
Screw
FindingtheAddress
6. FINDING THE CAMERA’S IP ADDRESS
Use the steps below to find the camera’s IP address and connect to the
camera over the local area network (LAN) using Veilux VMS, UPnP on
Windows® 7, or Bonjour® in Mac OS®.
6.1 Finding the Camera’s IP Address Using Veilux VMS
1. Install
Veilux VMS from the CD. Now Doubl e-click the Veilux VMS icon (
)on the
Desktop.
The l o g in screen appears.
2. Under User Name and
Password , enter the default Veilux VMS user name
( admin ) and password ( admin ). Click Login.
Enter Admin
Enter Admin
Click Login
3.
Veilux VMS opens and scans the l o c a l network for connected c a mer as.
Detected camera IP addresses on the LAN appear in the
Device List on
the
left side of the screen with a icon.
Found camera
IP address

13 14
FindingtheAddress
4. Click on a camera IP address in Device List to l o gin.
5. Under
User Name , enter the user name for the camera (default: admin).
Under
Password , enter the password for the camera (default: admin).
Click Continue.
Enter Camera User Name
(default: admin)
Enter Camera Password
(default: admin)
Click Continue to login
6.
The camera appears under the camera IP address. Click and drag the
camera to the display grid to open
it.
Click and drag the
camera to the display
grid to open
it
NOTE: For detailed instructions on using Veilux VMS, see the
Veilux VMS manual on the CD.
6.2 Finding the Camera’s IP Address using UPnP in
Windows® 7
NOTE: To use this method, your router must support UPnP and the c a mer a
and computer must be on the same network. UPnP is enabl ed in the c a mer a
by default, and c a n be enabled/disabl ed using Veilux VMS (check the
Veilux VMS manual for details).
FindingtheAddress
1. Click Start>Computer>Network . The camera’s IP address appears
under Network
Infr as tructur e.
Double-click to open
the camera
Network
2. Double-click the camera to open it in your default browser.
3. Under User Name and
Password , enter the camera’s User Name
(default:
admin ) and Password (default: admin ) and click Login .
Enter Camera User Name (default: admin)
Enter Camera Password (default: admin)
Click Login
6.3 Finding the Camera’s IP Address using Bonjour ® in
Mac OS®
NOTE: To use this method, the camera and computer must be on the same
network. Bonjour® is enabled by default, and can be enabled/disabl ed
using Veilux VMS (check the Veilux VMS manual for details).
1. Open Safari® browser and click the Bookmarks button ().

15 16
FindingtheAddress
2. Click Bonjour .The camera’s IP address appears in the Bonjour Devices
list.
3. Double-click the camera to open it in
Saf ari®.
Bookmarks
button
Bonjour
Double-click the camera’s IP address
4. Under User Name and
Password , enter the camera’s User Name
(default:
admin ) and Password (default: admin ) and click Login .
Enter Camera User Name (default: admin)
Enter Camera Password (default: admin)
Click Login
6.4 Finding the Camera IP using the BNC Test Cable
When the BNC test cable is connected to the camera, the IP address is shown
on the test monitor.
The camera must be connected to power to use the BNC
test cable.
NOTE: The default IP address of 192.168.0.120 is shown if the c a mer a
cannot obtain an IP address from the router. Check the Ethernet/power
connections and
router c o nfigur ation.
ConfiguringConnection
7. CONFIGURING REMOTE CONNECTION
Follow the steps below to configure your camera for connections over the
Internet using a web browser, Veilux VMS, or other VMS software.
Step 1 of 6: Locate the camera’s local IP address:
• See “4. Finding the Camera’s IP Address” on page 12 .
Step 2of 6: Port Forward your router:
You need to enable port forwarding for the following ports on your router to
the camera’s local IP address:
• HTTP Port (default: 80)
• Control Port (default: 30001)
NOTE: If you are configuring multiple IP cameras for individual r e mot e
access, you
must change the ports for each camera. Two cameras cannot
use the same port number .
NOTE: Port forwarding the RTSP and RTMP ports is not necessary unl es s
your installation has special r e quir ements.
There are two methods for port forwarding:
• You can manually port forward your router. See yo ur router’s user manual
for details. An example of aport forwarding screen is shown below.
HTTP 80 80 100
Control
30001
30001
100

17 18
Configuring Connection
Step 3of 6: Locate your camera’s MAC address:
1.
Open aweb browser and enter the camera’s IP address in the address
bar in the f o ll owing f o rmat:
http://
http://192.168.0.120:80
IP address
Colon
HTTP port number
2. Under User Name and
Password , enter the camera’s User Name
(default:
admin ) and Password (default: admin ) and click Login .
3. Click
Device Info and write down the MAC Address.
MAC Address
Step 4of 6: Register for DDNS:
Register for one of the DDNS services which are currently supported for use
with your IP camera. ADDNS account allows
you to set up aweb site
address that points back to your local network. The following outlines how to
set up your free
DDNS account.
NOTE: Y our router must support UPnP to enable DDNS.
NOTE: You may use the same DDNS account for multiple IP cameras on
the same LAN.
ConfiguringConnection
Step 5of 6: Enable DDNS on the camera:
1. Enter the camera’s IP address in your web browser. Log in and then
click
Network
Servic e>DDNS .
2.
Check Enable DDNS.
3. Configure the
f o ll owing:
• Provider: Select the ddns service you use..
• Domain Name: Enter the Domain Name you received from the
confirmation email you received after you created your
DDNS account
(e.g. mycamera.dyndns.org ).
• User Name: Enter the User Name .
• Password: Enter the account name Password
4. Click
OK to save settings.
Step 6of 6: Connect to the camera’s DDNS address:
1. Enter the camera’s
DDNS address in your web browser in the f o ll owing
fo r m a t :
http://
http:// mycamera.dyndns.org : 80
Colon
DDNS address
HTTP port number
2. Under User Name and
Password , enter the camera’s User Name
(default:
admin ) and Password (default: admin ) and click Login .
Once you have logged into your system using your
DDNS address, you can
connect to theIP camera from a remote location using a web browser,
Veilux VMS .

19 20
Configuring Connection
7.1 Connecting to a DDNS address using Veilux VMS
NOTE: Complete all the steps above before performing the f o ll owing
method.
1.
Open Veilux VMS and click Device Manager>Video Device Manager.
2. Click
Manager .The Device Maintenance window opens.
Enter the
camera’s
DDNS address
Control
Port
Click Add Click Save
3. Under
Device IP,enter the Domain Name from the confirmation email.
For example, enter
mycamera .dyndns,org .
4. Under
Control Port,enter the camera’s control port (default: 30001).
5.
(Optional) Under Device Name , enter aname for the c a mer a.
6. Click
Add to add the camera to the Device Lis t.
7. Click
Save to save changes. Click OK.
ConfiguringConnection
8. Close Device Maintenance and Device Manager, and return to the Liv e
Video
screen. The newly added camera will appear in Device Lis t.
Found camera
NOTE: A icon is shown for all cameras outside of the LAN. This does
not affect your ability to connect to the camera r e motel y .
9. Click on the camera in
Device List to l o gin. Enter the User Name (def ault:
admin ) and Password (default: admin ) and then click Continue.
Enter Camera User Name (default: admin)
Enter Camera Password (default: admin)
Click Continue
10.Click and drag the camera to a display grid screen to open
it.
Click and drag the
camera to the display
grid to open
it
NOTE: For detailed instructions on using Veilux VMS, see the
Veilux VMS manual on the CD.

21 22
Configuration
8. WEB CONFIGURATION
The camera includes abuilt-in web interface that can be accessed using a
web browser.
8.1 Supported Browsers
• Google Chrome, Mozilla Firefox, and Apple Safari® (via Adobe Flash
Player)
• Microsoft Internet Explorer® 7.0 or later, 32-bit version (via ActiveX®)
8.2 Chrome, Firefox, and Safari Setup
1. Connect the camera to your l o c a l network and find the camera’s IP
address.
See “6. Finding the Camera’s IP Address” on page 12 .
2.
Open your browser and enter the camera’s IP address in the address bar
in the
f o ll owing f o rmat:
http://
http://192.168.0.120:80
Colon
Camera IP address
HTTP port number
NOTE: You can also connect to the camera using a DDNS address (DDNS
setup and port forwarding required; see “7. Configuring Remote
Connection” on
page 16 for det a ils).
3. Under User Name and
Password , enter the camera’s User Name
(default: admin ) and Password (default: admin ) and click Login.
Enter Camera User Name (default: admin)
Enter Camera Password (default: admin)
Click Login
4. The main screen for the camera web interface opens. From here you can
view and configure the
c a mer a.
NOTE: If you do not see video from the camera, make sure your c o mputer
has the latest v e r s ion of Adobe Flash Player ins t a ll ed (visit http://
www.adobe.com/ to download the latest version). After installing Flash
Player, restart your browser and reconnect to the camera.
8.3 Internet Explorer® Setup
Step 1of 2: Change Internet Explorer security settings for ActiveX®:
1.
Open Internet Explorer and open the Security tab.
• Internet Explorer 8: Click Tools > Internet Options and select the
Security tab.
• Internet Explorer 9: Click > Internet Options and select the Security
tab.
2. Click
Custom Level.
Click Custom level

23 24
Configuration
3. Under
Download unsigned ActiveX controls , click Prompt
(recommended) or Enable.
Select Enable or Prompt under
Download unsigned ActiveX controls
Click OK
4. Click OK . Click OK again to save changes.
Step 2of 2: Log into camera:
1.
Connect the camera to your l o c a l network and find the camera’s IP
address.
See “6.Finding the Camera’s IP Address” on page12.
2. Enter the camera’s IP address in the address bar in the
f o ll owing f o rmat:
http://
http://192.168.0.120:80
IP address
Colon
HTTP port number
NOTE: You can also connect to the camera using a DDNS address (DDNS
setup and port forwarding required; see “7. Configuring Remote
Connection” on
page 16 for det a ils).
3. Under User Name and
Password , enter the camera’s User Name
(default: admin ) and Password (default: admin ) and click Login.
Enter Camera User Name (default: admin)
Enter Camera Password (default: admin)
Click Login
4. If your computer has Flash Player ins t a ll ed, the main screen for the
camera web interface opens. From here you can view and configure the
ca m e ra .
NOTE: The ActiveX plug-in may provide smoother video performance than
Flash Player.
To use ActiveX, click the message above the video window.
Then click inside the video area, select Install this Add-on for all users on
this computer , and follow the prompts.
Install
ActiveX plug-in
NOTE: If your computer does not have Flash Player ins t a ll ed, you will be
prompted
t o select if y o uwould like t o use Activ eX or Flash Play er t o connect
to the ca m e ra:
• Click to play live video with ActiveX control to reduce latency
(recommended): Uses an ActiveX plug-in to connect to the camera. To
install the plug-in, click on the
video area, and select Install this Add-on
for all
users on this computer , and follow the prompts.
• Click to download the latest version of Flash Player to play live video:
Opens alink to download Flash Player from Adobe’s website. After
completing the installation, restart your browser and reconnect to the
camera.
Select
ActiveX or Flash Player

25 26
Configuration
8.4 Web Interface/Live Video Overview
Camera
configuration
menus
Click and drag to zoom in. Right-click and
select
ZoomOut to zoom out.
Double-click inside window for
full-screen
Select Stream
TIP: Select stream2 for better performance for remote
connections. Stream2 has alower resolution than stream1.
The Live video page appears when you log into the camera. Live video
requires an ActiveX® plug-in or
Adobe Flash Player.
8.4.1 Live Video Menu
You can right-click on the live video area to bring up the Live Video Menu.
Right-click on the
video area to
open the Live
Video Menu
The Live Video Menu contains the following options:
• Full Screen: Open the video in full screen. Press ESC to exit full sc reen.
• Sensor Config: Configure the camera sensor settings. See “8.17 Sensor
Configuration” on
page 55.
• ZoomIn: Zoom in one level.
• ZoomOut: Zoom out one level.
• Restore Panorama: Zoom out all the way.
8.4.2 Configuring Camera Settings
• Click the options on the left to configure camera settings. Setting options
are detailed in the remainder of this section.
Click to select
camera menus
TIP: Some sub-menus have aReset button. This button will reset the
sub-menu options to factory defaults.
You then have to click OK to save
changes.

27 28
Configuration
8.5 Device Info
The Device Info page shows information about your IP camera, such as the
Device Name (which appears in the Device List in Veilux VMS), firmware
version, MAC address, and camera inputs and outputs. You can also
configure the Device Name for your camera.
ATTENTION: The device ID is unique. Do not change it unless your
installation has special requirements.
To configure the Device Name:
1. Click
Device Info.
2. Under
Device Name , enter the desired device name and then click Set.
8.6 Stream Configuration
The Stream Configuration page allows you to configure the camera’s video
streams.
The camera supports three different video streams. This allows
you to have a high quality recording stream (stream1), a lower quality stream
(stream2) to preserve bandwidth for remote connections, and an MJPEG
stream for applications requiring MJPEG.
To configure video streaming settings:
1. Click Stream
Configuration . Under Stream ID, select the stream you
would like to c o nfigur e.
2. Configure the
f o ll owing:
• Video Encode Type: Select the Video Encoding type for the stream.
Stream1 and stream2 can be configured for
H.264 High Profile,H.264
Main Profile,or H.264 Base Profile.Stream3 supports MJPEG only.
• Audio Encode Type: Select the Audio Encoding type for the stream:
G711_ALAW , G711_ULAW , or RAW_PCM.
• Resolution: Select the resolution for the stream. Stream1 and stream3
can be set to 1920x1080 or 640x360 .Stream2 can only be set to 640x360.
Stream3 can only be set to 1920x1080.

29 30
Configuration
• Frame Rate: Select the frame rate for the stream up to maximum of
30FPS for stream1 or stream2 or 12FPS for stream3.
NOTE: Frame rate ma y be a utoma t ical l y adjusted to ac c o un t f o r bandwidth
limitations.
• I Frame interval: Select the interval for Iframes: 1,2,or 3. The default
value of 2should be used unless there are special requirements.
The I
Frame interval
does not apply to stream3.
• Bit Rate: For stream1 or stream2, select CBR (Constant Bit Rate) or VBR
(Variable Bit Rate). Enter the desired bit rate below in kbps. Stream3 only
supports VBR.
• Quality: Select the video quality between 1(lowest) and 9(highest).
TIP: Aquality of 7provides a good picture. It is not recommended to set a
high quality value with asmall
VBR bit rate.
3. Click
OK to apply changes.
8.7 Device Configuration
Device Configuration contains the following sub-menus:
• Local Network
• Device Port
• Camera
• Date &Time
• OSD
• Microphone
• BNC Video Output
• Language
• Multicast (Not supported)
• Dome PTZ (Not supported)
8.7.1 Local Network
The Local Network page shows the camera’s current IP address and
network parameters if
DHCP is enabled. It also allows you to set astatic IP
address for the camera
(see below), set the networking parameters, and to
select
IPv4 or IPv6.
NOTE: DHCP is dis abled by default. When DHCP is enabled, the IP address
is shown under
DHCP IP. Use the IPScan tool on CD to configure a static
IP address. This will prevent the camera IP address changing in the event
of apower f a ilur e.
To configure the camera’s networking parameters:
1. Click
Device Configuration>Local Network.
2. Under IP
Protocol , select IPv4 or IPv6 . If you would like to use IPv6, mak e
sure it is supported on your network.
You may need to contact y o ur
network administrator or ISP for details.
3. Select
Device obtain an IP address automatically to use DHCP or Device
use the following IP address to set a static IP address for the camera. If
you are using a static IP address, configure the f o ll owing:
• IP Address: Enter the IP address you would like to assign to the camera.
Make sure the IP address is available on your network.
• Subnet Mask: Enter the subnet mask.
• Preferred DNS Server/Alternate DNS Server: Enter desired DNS
servers.

31 32
Configuration
4. Click
OK to save changes. The camera will restart with the new IP
address.
8.7.2 Device Port
The Device Port page ( Device Configuration>Device Port)allows you to
configure the camera’s port configuration.
The camera has the following
ports:
• Control port: The default is 30001. Enables video streaming.
• HTTP Port: The default is 80. Enables web access. Please note that if the
HTTP is port is anything other than 80, you must enter http:// before the
camera’s
IP address and colon (:) and the HTTP port after the IP address
when connecting using an Internet browser
(e.g. if the HTTP port is 85,
enter http://192.168.x.x:85).
• RTSP Port: Default is 554. Only used for special applications requiring
RTSP streaming, such as VLC player or quicktime movie.
• RTMP Port: Default is 8080. Only used for special applications.
NOTE: If you are configuring multiple IP cameras for individual r e mot e
access (without an NVR or server), you must change all the ports for each
camera.
Two cameras cannot use the same port number .
To change camera ports:
1. Configure the camera ports as required and then click OK.
2. Click
Device Configuration>Device Port.
8.7.3 Camera
The Camera page ( Device Configuration>Camera ) allows you to configure
the
Channel Name, which appears on the camera OSD and the video system
frequency.
To change the Channel Name:
• Configure the Channel Name as needed and then click the Set button
next to Channel Name.
To change the video system frequency:
• Select the desired setting under Video System and then click the Set
button next to Source Resolution.
8.7.4 Date &Time
The Date &Time page allows you to configure the camera’s date and time.