Velleman PIC K8076 User manual

PIC® programmer board
K8076
ILLUSTRATED ASSEMBLY MANUAL H8076IP-1
Total solder points: 202
Difficulty level: beginner 12345 advanced
Thisboard can programawide range
ofMicrochip® PIC™microcontrollers

FR Vous trouverez la traduction de cette notice sur le CD, avec d'autres informations
NL Vertaling van deze handleiding, als ook meer gegevens kan men terugvinden op de CD.
UK The translation of this manual and all other information can be found on the CD.
D Dieübersetzung dieser anleitung und alle anderen Informationen finden Sie auf der CD.
SSvensk Bruksanvisning och annan information finns på medföljande CD.
SF Tämän käyttöohjeen sekä muun informaation suomenkielinen käännös on oheisella CD:llä.
ILa traduzione di questo manuale e tutte le informazioni concernenti l'unità possono essere trovate sul CD.
DK Oversæ ttelsen af denne manual, samt alle ø vrige informationer vedrø rende enhederne, kan findes på CD'en.
SP La traducción de este manual de instrucciones y toda otra información sobre los dispositivos se encuentran en el CD
PA traduçã o deste Manual e toda a informaçã o referente às unidades pode ser encontrada no CD
This device complies with Part 15 of the FCC Rules provided the enclosed instructions
are followed to the letter. Use of the device is subject to the following conditions: (1) this
device must not cause harmful interference and (2) the operation of this device should
not be influenced by unwanted interference.
More information about FCC can be look at http://www.fcc.gov

4
Features:
 onboard configurable 40 pin. ZIF socket
 Microcontroller selection using patch jumper
 easy to use programming PICprog2006TM software included
 SUBD connector set included
Specifications:
 power supply: 15V DC, min. 300mA adapter (Ex. PS1508)
 serial port connector: 9 p. SUBD
 dimensions: 132x65x20mm / 5,23 x 2,57 x 0,79"
 currently supported controllers (rev. 2.0.0.0) :

PIC10F200
 PIC12C508A,PIC12CE518
 PIC12F629,PIC12F675
 PIC16F54
 PIC16F84A
 PIC16F870,PIC16F871,PIC16F872,PIC16F873*,PIC16F874*
 PIC16F876,PIC16F877*
 PIC16F627,PIC16F627A,PIC16F628,PIC16F628A
 PIC16F648A* PIC16F630,PIC16F676
 PIC18F2550,...
 (*): under test
Features & Specifications
Minimum system requirements:
 IBM Compatible PC, Pentium or better
 Windows? 98/ME/NT/2000/XP
 CDROM drive
 free REAL serial (RS232) port required*
(*) The functioning of the PIC programmer card cannot be guaranteed through a USB conversion cable.

5
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
• A good quality soldering iron (25-40W) with a small tip.
• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’and will
protectthe tip,and enables you to makegoodconnections. When solderrolls off the tip, it needs cleaning.
• Thin raisin-core solder. Do not use any flux or grease.
• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes.
• Needle nose pliers, for bending leads, or to hold components in place.
• Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
⇒ Make sure the skill level matches your experience, to avoid disappointments.
⇒ Follow the instructions carefully. Read and understand the entire step before you perform each operation.
⇒ Perform the assembly in the correct order as stated in this manual
⇒ Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
⇒ Values on the circuit diagram are subject to changes.
⇒ Values in this assembly guide are correct*
⇒ Use the check-boxes to mark your progress.
⇒ Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’on a separate leaflet.
0
.0
0
0

6
Assembly hints
1.3 Soldering Hints :
1- Mount the component against the PCB surface and carefully solder the leads
2- Make sure the solder joints are cone-shaped and shiny
3- Trim excess leads as close as possible to the solder joint
REMOVE THEM FROM THE TAPE ONE AT A TIME !
AXIAL COMPONENTS ARE TAPED IN THE COR-
RECT MOUNTING SEQUENCE !

7
 R1 : 1K5 (1 - 5 - 2 - B)
 R2 : 3K3 (3 - 3 - 2 - B)
 R3 : 3K3 (3 - 3 - 2 - B)
 R4 : 3K3 (3 - 3 - 2 - B)
 R5 : 3K3 (3 - 3 - 2 - B)
 R6 : 100K (1 - 0 - 4 - B)
 R7 : 100K (1 - 0 - 4 - B)
 R8 : 100K (1 - 0 - 4 - B)
 R9 : 10K (1 - 0 - 3 - B)
2. Resistors
R...
Construction
 D1 : 1N4007
 D2 : 1N4148
 D3 : 1N4148
 D4 : 1N4148
1. Diodes. Watch the polarity!
D...
CATHODE
 C1 : 100nF (104, u1)
 C2 : 100nF (104, u1)
 C3 : 100nF (104, u1)
5. Capacitors
 R10 : 47 (4 - 7 - 0 - B - 9)
 R11 : 220 (2 - 2 - 1 - B - 9)
3. Metal film resistors
R...
 VR1 : UA7812
4. Voltage regulator
 IC1 : 16P
 IC2 : 16P
6. IC sockets, Watch the
position of the notch!

8
 T1 : BC547
 T2 : BC557
Construction
7. Transistors.
 LD1: 3mm Green
 LD2: 3mm Yellow
 LD3: 3mm Yellow
 LD4: 3mm Red
9. LEDs. Watch the polarity !
COLOR= 2...5
LD...
CATHODE
 SK5 : 20P
 SK6 : 20P
10. Headers
 VR2 : UA78L05
8. Voltage regulator
VR...
 SK1 : 15VDC (Power)
11. DC - Jack
 SK3 : 5 poles
 SK4 : 5 poles
12. Board to wire connector
 C4 : 10µ F
 C5 : 10µ F
 C6 : 1µ F
 C7 : 1µ F
 C8 : 1µ F
 C9 : 1µ F
 C10 : 220µ F
13. Electrolytic Capacitor.
Watch the polarity !
C...

9
Construction
 SK2 : RS232 (9p female)
14. Sub D - connector
 IC1 : MAX232
 IC2 : CD4049
16. IC’s. Watch the position
of the notch!
Mount the rubber feet on the solder side of the PCB, see fig 1.0.
17. Rubber feet
FIG 1.0
 SK5 : 40p
15. ZIF socket

10
Construction
1
62
73 84 95
SK1
SUBD 9-POLE MALE
1
62 73 84 95
SK2
SUBD 9-POLE FEMALE
Mount a SUBD connector on both sides of a shielded 6-core cable. Refer to fig. 2.0 below.
.
18. Serial cable
FIG 2.0
If you do not assemble cables with the included SUBD connectors, pay attention to the
following: all conductors must be connected “PIN to PIN”.