Vertex Fasteners VA0262 Setup guide

Service and Repair Instructions
Vertex Fasteners Pneumatic Stapler Type
VA0262
This Spare parts list/service instructions and the
enclosed operator's manual constitute the operating
instructions. Read both before use and strictly
observe safety instructions.
To replace worn and broken parts
Attention! Always disconnect the tool from its air supply
and empty staple magazine. The cap has to be fixed
with a torque wrench adjusted to 8 Nm.
To replace driver blade
Loosen cap VC7075 (fig. 1). Remove piston-driver blade
assembly with a spare driver blade (fig. 2). With a pin
punch tap out pin VC7330 (fig.3). The driver blade can
then be removed. Replacement of the blade is a reversal
of the above procedure.
Replacement of the piston O-ring
See instructions "to replace driver blade", then replace
O-ring VC7326 (fig. 3), apply grease or oil before
refitting.
A
fter inserting the pin VC7330 the holes at both sides o
f
the plastic piston have to be deformed again to prevent
movement of the pin, which can then damage the
cylinder. In order to do this, lay a drift punch, diameter
3mm, across the hole (fig.4) and hit the punch drift with a
hammer so that the hole is deformed a little bit.
To replace bumper
See instruction "to replace driver blade", then remove
bumper and cylinder. Before refitting grease the parts
with O-ring grease or oil.
To replace tension spring and pusher
With a pin punch tap out pin VC7065 from the cover
stop. Push the cover stop forward and remove, then
remove rail assembly from the magazine cover. Hook
new tension spring VC7063 onto feeder bar; lead it
backwards under the pulley and over the hook inside the
rail assembly (fig. 5).
To replace O-rings on valve system
Remove pin VC7329 and remove the trigger. Remove
cap screw VC7365 to release valve cap (fig. 6). Remove
valve gasket and tap out all components of the valve.
Figure 7 shows a breakdown of the valve components,
which are accessible once the valve cap has been
removed. Replace the O-rings and grease, or oil before
re-assembling.
To replace silencer
Remove cover as described above. Remove pin
VC7065. Remove latch cover and leg spring. Take out
silencer towards the rear and replace.
1
2
3
4
1798 Sherwin Avenue
Des Plaines, IL 60018 U.S.A.
EMAIL: [email protected]
PHONE: [phone] FAX: [phone]

Parts Identification
Vertex Fasteners Pneumatic Stapler Type VA0262

Tool Parts
Vertex Fasteners Pneumatic Stapler Type VA0262
Call-out Number Part Number Description Quantity
1 VC7276 O-ring 1
2 VC7280 O-ring 1
3 VC7281 O-ring 1
4 VC7292 O-ring 1
5 VC7300 O-ring 1
6 VC7307 O-ring 2
7 VC7311 O-ring 1
8 VC7313 O-ring 1
9 VC7326 O-ring 1
10 VC7065 Pin 1
11 VC7329 Pin 1
12 VC7330 Pin 1
13 VC7354 Washer 1
14 VC7365 Socket head cap screw 1
15 VC7390 Socket head cap screw 4
16 VC7389 Socket head flat screw 1
18 VC7063 Tension spring 1
20 VC7061 Pusher 1
21 VC7058 Piston 1
22 VC7059 Valve stem 1
23 VC7016 End piece 1
24 VC7013 Cover stop 1
25 VC7066 Leg spring 1
26 VC7067 Latch 1
27 VC7068 Latch cover 1
28 VC7070 Nose plate 1
29 VC7072 Bumper 1
30 VC7073 Body 1
31 VC7074 Muffler 1
32 VC7075 Cap 1
33 VC7076 Damper 1
34 VC7077 Cylinder 1
35 VC7078 Cylinder support 1
36 VC7079 Valve seal 1
37 VC7080 Valve cap 1
38 VC7081 Trigger 1
39 VC7082 Valve cylinder 1
40 VC7083 Valve shaft 1
41 VC7084 Intermediate valve 1
42 VC7085 Rail assembly 1
43 VC7086 Magazine cover 1
44 VC7087 Front nose 1
45 VC7088 Driver blade 1
46 VC7089 Pulley 1
47 VC7120 Pin 1
48 VC7014 Stop 1
49 VC7001 Split pin 1