Vertex VA0266 Setup guide

Service and Repair Instructions
Vertex Fasteners Pneumatic Stapler Type
VA0266
This Spare parts list/service instructions and the
enclosed Operator's Manual constitute the
Operating Instructions. Before using read both and
strictly observe safety instructions.
Attention! Always disconnect the tool from its air supply
and empty magazine before attempting any repair.
A
lways tighten the cap with a torque wrench adjusted to 7
Nm.
Removing piston and driver blade
Take out 4 cap screws VC7378 and remove the complete
cap and valve shaft assembly (fig. 1). The piston with
driver blade can now be removed by using a spare driver
blade and pushing them from below (fig. 2). Use a pin
punch for removing the pin VC7027 and split pin VC7337
(fig. 3). Any damaged parts must be replaced. Before
refitting, the piston O-ring should be greased.
Changing of bumper and cylinder
Take off cap screws VC7371, VC7373, and VC7379 now
remove magazine. Take out piston-driver assembly and
bumper. Gently tap the housing on a wooden surface.
By the impact, the cylinder will come out and can easily
be removed from the housing. Replace the damaged
parts and grease before refitting (fig. 4).
Replacement of the pusher and roller spring
Pull back the pusher enough to expose the front roller
spring attachment and e-ring retainer. Remove e-ring
retainer and undo front of spring. Remove the e-ring
retainer from the pusher stop. Remove pusher stop, and
spring. Slide the pusher off the back of the staple carrier
and remove the spring. Replace any worn or defective
parts. Reconnect the spring in the front and re-install the
e-ring retainer. With the spring in the pusher guide the
spring along the carrier to the end and re-install the
pusher over the carrier. Re-install the pusher stop, spring,
and e-ring retainer
Changing of O-rings in head valve assembly
Remove the cap as described above. Take main valve
out of the cap and replace worn 0-rings.
Grease O-rings before refitting.
1
2
3
5
4

Tool Parts
Vertex Fasteners Pneumatic Stapler Type VA0266
Call-out # Part Number Description Quantity Call-out # Part Number Description Quantity
1 VC7276 O-ring 53 VC7169 Main valve
2 VC7278 O-ring 54 VC7172 Valve bush
3 VC7306 O-ring 55 VC7184 Driver guide
4 VC7293 O-ring 56 VC7006 Hook plate
5 VC7295 O-ring 57 VC7007 Plate
6 VC7314 O-ring 58 VC7004 Body
7 VC7319 O-ring 59 VC7005 Nose
8 VC7320 O-ring 60 VC7010 Back plate
9 VC7321 O-ring 61 VC7009 Staple carrier
10 VC7322 O-ring 62 VC7008 Pusher stop
11 VC7324 O-ring 63 VC7003 Valve shaft
12 VC7327 Seal 64 VC7187 Bushing
13 VC7331 Pin 65 VC7188 Pin
14 VC7337 Split pin 66 VC7189 Leg spring
15 VC7341 E-ring retainer
16 VC7343 Retainer
17 VC7369 Socket head cap screw
18 VC7371 Socket head cap screw
19 VC7376 Socket head cap screw
20 VC7378 Socket head cap screw
21 VC7379 Socket head cap screw
22 VC7345 Lock washer
23 VC7373 Button head socket screw
24 VC7386 Hex nut
25 VC7000 Button head socket screw
28 VC7027 Pin
29 VC7028 Reducer bushing
30 VC7029 Piston
31 VC7193 Pressure Spring
32 VC7032 Pressure Spring
33 VC7054 Valve Spring
34 VC7031 Spring Stop
35 VC7051 Perforated plate
36 VC7166 Perforated plate
37 VC7052 Muffler
38 VC7053 Cap insert
39 VC7155 Trigger
41 VC7387 Roller spring
42 VC7186 Carrier cover
43 VC7017 Pusher
44 VC7191 Spring Retainer
45 VC7160 Bumper
46 VC7161 Cylinder
47 VC7162 Trip yoke
48 VC7163 Nose plate
49 VC7164 Driver blade
50 VC7165 Gasket
51 VC7167 Cap
52 VC7168 Exhaust valve
THIS DOCUMENT DRAWING IS STRICTLY THE SOLE AND PROPRIETORY PROPERTY OF VERTEX FASTENERS A LEGGETT & PLATT COMPANY. THE ENGINEERING AND DESIGN DATA PRINTED, WRITTEN,
DISCLOSED AND CONTAINED HEREIN IS NOT TO BE REPRODUCED DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE WRITTEN CONSENT AND PERMISSION FROM VERTEX FASTENERS.

THIS DOCUMENT DRAWING IS STRICTLY THE SOLE AND PROPRIETORY PROPERTY OF VERTEX FASTENERS A LEGGETT & PLATT COMPANY. THE ENGINEERING AND DESIGN DATA PRINTED, WRITTEN,
DISCLOSED AND CONTAINED HEREIN IS NOT TO BE REPRODUCED DISCLOSED OR USED IN WHOLE OR PART WITHOUT THE WRITTEN CONSENT AND PERMISSION FROM VERTEX FASTENERS.