Vertiv Liebert LDMF User manual

Liebert®
LDMF™ Distribution Monitoring
User Manual

Technical Support Site
If you encounter any installation or operational issues with your product, check the pertinent
section of this manual to see if the issue can be resolved by following outlined procedures.
Visit https://www.VertivCo.com/en-us/support/ for additional assistance.
The information contained in this document is subject to change
without notice and may not be suitable for all applications. While
every precaution has been taken to ensure the accuracy and
completeness of this document, Vertiv assumes no responsibility
and disclaims all liability for damages resulting from use of this
information or for any errors or omissions. Refer to other local
practices or building codes as applicable for the correct methods,
tools, and materials to be used in performing procedures not
specifically described in this document.
The products covered by this instruction manual are manufactured
and/or sold by Vertiv This document is the property of Vertiv and
contains confidential and proprietary information owned by Vertiv.
Any copying, use or disclosure of it without the written permission of
Vertiv is strictly prohibited.
Names of companies and products are trademarks or registered
trademarks of the respective companies. Any questions regarding
usage of trademark names should be directed to the original
manufacturer.

Vertiv | Liebert® LDMF™ Distribution Monitoring User Manual | i
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.0 GLOSSARY OF ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.0 PRODUCT OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.0 MAJOR COMPONENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
3.1 PM4 Monitor Board (PMB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2 PM4 Interface Board (PIB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.3 PM4 Large Interface Board (PLIB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.4 Branch Circuit Monitoring Sensor Module (BSM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.5 Power Supply With EMI Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.6 Human-Machine Interface/Display Assembly (Optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.7 PM4 Adapter Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.0 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4.1 Installing a BSM (CT Module Assembly) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.1.1 Connecting Panelboards A and B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2 Installing a Solid-Core Current Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3 Installing a Current Transformer on the PIB Interface Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.4 Connecting a Current Transformer to the PM4 Large Interface Board (PLIB) . . . . . . . . . . 14
5.0 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1 Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2.1 LDMF Setup Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2.2 Modbus Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.3 Downloading the Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
5.4 Using the Monitor Tool (Used Only for Startup and Diagnostics). . . . . . . . . . . . . . . . . . . . . . .20
5.4.1 Starting the Monitor Tool. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
5.4.2 Monitor Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.4.3 Panel Status and Real-Time Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.4.4 Main Breaker Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.4.5 Breaker Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.4.6 Mode Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Vertiv | Liebert® LDMF™ Distribution Monitoring User Manual | ii
5.5 Using the Configuration Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
5.5.1 Starting the Configuration Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
5.5.2 Main Configuration Window Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.5.3 Load a Configuration File from Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
5.5.4 Install Configuration Changes in the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
5.5.5 Save the Configuration File to Disk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.5.6 Select Panel to View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.5.7 Select Breakers to View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.5.8 Edit the Liebert LDMF Unit Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.5.9 Edit the Panel Properties or Set a Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.5.10 Edit the Breaker Properties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
5.5.11 Add a Circuit Breaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
5.5.12 Adding a Subfeed Breaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.5.13 Delete a Circuit Breaker/Subfeed Breaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.6 Upgrading the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
5.7 Display Controls (HMI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
5.7.1 Controls and Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.7.2 Liebert LDMF Parameter Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
5.7.3 Liebert LDMF Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
5.7.4 Liebert LDMF Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
6.0 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
7.0 TROUBLESHOOTING / FREQUENTLY ASKED QUESTIONS . . . . . . . . . . . 43
FIGURES
Figure 1 RS-232 port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 2 Main panelboard screens—examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Figure 3 Subfeed screens—examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 4 Branch breaker screens—examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
TABLES
Table 1 CT matrix for the Liebert LDMF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Table 2 Large branch breaker CT wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Table 3 CT Table for Interface Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 4 CT Table for PM4 Large Interface Board #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 5 CT Table for PM4 Large Interface Board #2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Table 6 Parameters monitored for breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 7 Alarm conditions and factory setpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 8 Monitor Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 9 Monitor mode buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Table 10 Overview of main Configuration window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Table 11 Edit breaker properties and description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 1
IMPORTANT SAFETY INSTRUCTIONS
ELECTROMAGNETIC COMPATIBILITY—The Liebert LDMF as a functional component of a
power distribution and supply product complies with the limits for a Class A Digital Device,
pursuant to Part 15 of FCC rules. Operation is subject to the following two conditions:
• This device must not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired
operation.
Operating this device in a residential area is likely to cause harmful interference that users must
correct at their own expense.
Liebert LDMF as a functional component of a power distribution and supply product complies
with the requirements of EMC Directive 2004/108/EC and the published technical standards.
Continued compliance requires installation in accordance with these instructions and use of
accessories approved by Vertiv.
WARNING
As with all types of electrical equipment, dangerous voltages exist within the equipment
where the Liebert LDMF Distribution Monitor components are installed. For maximum
safety, ensure power is removed and circuit breakers/disconnects are tagged/locked out
per all applicable national, state and local electrical codes prior to working inside
equipment.
The area around the equipment must be free of any debris or standing water.
All power and control wiring must be installed by a qualified electrician in accordance with
the NEC and all applicable national, state and local codes.
ONLY qualified service personnel should perform maintenance and/or service on the
Liebert LDMF system. When performing maintenance and/or service on any component,
verify test equipment is insulated and has been inspected prior to use.
To avoid damage to the circuit boards, personnel handling these components should be
wearing an electrostatic discharge strap or other approved protective device.
When replacing or installing a solid core Current Transformer (CT), power must be
removed from equipment to prevent damage to the CT and/or circuit board. If the CT is a
split-core design, follow proper electrical safety procedures and ensure the CT wires are
connected to the applicable burdening circuit before attaching the CT around the
conductor.
These safety precautions are to be used in conjunction with NEC and local/state electrical
code.

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 2
1.0 GLOSSARY OF ABBREVIATIONS
The following abbreviations are used in this manual.
BCMS Branch Circuit Monitoring System
BMS Building Management System
BSM Branch Sensor Module
DSP Digital Signal Processor
GUI Graphic User Interface
HMI Human-Machine Interface
IGM Information Gathering Module
LDMF Liebert Distribution Monitor Front Access
LDMFS Liebert Distribution Monitor Front (Square-D Panelboards)
LDMFG Liebert Distribution Monitor Front (GE Panelboards)
LDMFI Liebert Distribution Monitor Front (I-Line Panelboards)
LDMF4 Liebert Distribution Monitor Front (480V Distribution
Cabinets)
PAB PM4 Adapter Board
PCD Power Conditioning and Distribution
PDU Power Distribution Unit
PM4 Power Monitoring 4th Generation
PIB PM4 Interface Board
PLIB PM4 Large Interface Board
PMB PM4 Monitoring Board
STP Service Terminal Port

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 3
2.0 PRODUCT OVERVIEW
The Liebert LDMF monitors the main panelboard circuit breaker and individual panelboard
branch circuit breakers. The measurements are used to report the voltage, current and alarm
conditions for each breaker. The Liebert LDMF utilizes branch circuit sensor modules and
individual current transformers (CT) to monitor current. In addition, the Liebert LDMF monitors
options like subfeed and output circuit breakers and provides a full array of power parameters
and alarms.
The Liebert LDMF is available as an option for the Liebert PPC™, Liebert FDC™, Liebert FPC™,
Liebert RX™and Liebert RDC™.
The Liebert LDMF system can communicate with a Building Management System (BMS) and
Liebert SiteScan®Web via optional Liebert IntelliSlot™cards or Liebert SiteLink®interface.
The Liebert LDMF consists of a monitor board, interface board, optional local display and Branch
Sensor Modules (BSM).
The Liebert LDMF is capable of receiving input from current branch sensor modules. The sensor
module (BSM) contains 100A current transformers (CTs) encapsulated in an epoxy-filled plastic
enclosure designed to be mounted next to the panelboard. Sensor modules are designed to work
3/4" or 1"-spaced panelboards. If a sensor module CT fails, connections are provided for up to six
replacement CTs. The optional CTs can be attached directly to the load cable feeding the failed
CT.
Higher-rated CTs may be used for monitoring optional subfeed circuit breakers. For subfeed
breakers, such as main panelboard breakers, the Liebert LDMF monitors not only the three-phase
current but also the ground and neutral current. These subfeed circuit breakers are in addition to
the panelboard circuit breakers that can be monitored through the BSM. The Liebert LDMF can
accommodate 18 individual large current transformers.
If your Liebert power center is supplied with a Square D®I-Line™panelboard, the Liebert LDMF
can monitor it as well as its output breakers. A PM4 Large Interface Board (PLIB) replaces the
panelboard PM4 Interface Board (PIB) and can monitor up to 42 CTs. Each PLIB can monitor
eight four-wire or five-wire I-Line and/or subfeed breakers including ground and neutral current.
There are two (2) PLIBs per monitor board that can monitor up to 16 five-wire I-Line and/or
subfeed breakers.
The Liebert LDMF system includes three Liebert IntelliSlot ports for remote communication.
Optional Liebert IntelliSlot cards can provide the following remote communications:
• IS-WEBS card for SNMP/WEB with RJ-45 connection to Ethernet LAN
• IS-485S card for Modbus 485, 2-wire connection
• IS-IPBMS card for Modbus IP, with RJ-45 connection to Ethernet LAN
• IS-UNITY-DP card for HTTP/HTTPS, Vertiv Protocol, e-mail, SMS, SNMP v1/v2c/v3, BACnet IP/MSTP and
Modbus TCP/RTU output using a serial RS-485 two-wire connection
In addition to Liebert LDMF remote communications, an optional local display offers easy-to-use
viewing of electrical data for various branch breakers as well as alarm details such as the type and
source of each alarm.

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 4
3.0 MAJOR COMPONENTS
3.1 PM4 Monitor Board (PMB)
The PM4 Monitor Board (PMB) is the main processing and storage circuit board. The PMB
contains the non-volatile memory where the configuration file is stored. The CT Module
Assemblies will connect directly to the PMB via the 4 ribbon cables connectors. The PMB is a
DSP-based logic controller with internal flash memory to store breaker configuration, alarms and
energy data. The on-board battery supplies power to the real-time clock.
All the electrical parameters are accumulated on the PMB for processing to Liebert Velocity
protocol for remote monitoring and the HMI interface for the local display. Kilowatt-hours (kWh)
data is accumulated on this board for the panelboard mains, subfeeds and each branch circuit
breaker. A remote command can be used to reset the accumulated energy data.
Additional PMB Capabilities
• Six (6) auxiliary CT connectors, which allow for replacing a failed CT.
• A DB9 serial port on the outside panel is available for local configuration.
3.2 PM4 Interface Board (PIB)
The Liebert LDMF PM4 Interface Board (PIB) provides connections for the voltage and currents
of the panelboard main circuit breaker as well as the CT current for any installed large branches
or subfeed breakers (maximum of 18 CTs).
For the large branches or subfeed breakers, the nine CTs on the A side of the board are normally
associated with the A-side voltages for power calculations. The B-side CTs are normally
associated with the B-side voltages. A cross-configuration tool allows changing that association
for subfeeds.

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 5
The 18 large branch CT inputs can also be used to monitor up to three subfeed circuit breakers.
This is configured using the configuration tool (see 5.5 - Using the Configuration Tool). The CTs
from the B side of the PIB are cross-configured to the A side so that the three subfeeds appear
within the A-side panelboard register space. The 18 large branch breakers require CT’s with 1A
secondary.
3.3 PM4 Large Interface Board (PLIB)
WARNING
Before connecting a large CT to the PIB, note the CT MUST have a 1A secondary.
Connecting
anything other than a 1A secondary CT will damage the PIB and the CT.
To ensure the proper current ratio and accuracy, the CTs should be purchased through
Vertiv. See Table 1 for details. Contact your local Vertiv representative or call Vertiv
Support at 800-543-2378.
Table 1 CT matrix for the Liebert LDMF
Part Number Description Phase CT Ground CT Neutral CT
539217G1-L 3-pole 0-100A Subfeed Breaker 5W CT Kit 200:1 100:1 200:1
539217G2-L 3-pole 125-225A Subfeed Breaker 5W CT Kit 500:1 100:1 500:1
539217G3-L 3-pole 250-400A Subfeed Breaker 5W CT Kit 1000:1 100:1 1000:1
539217G12-L 3-pole 125-225A Subfeed Breaker 4W CT Kit 500:1 — 500:1
539217G13-L 3-pole 250-400A Subfeed Breaker 4W CT Kit 1000:1 — 1000:1
539217G4-L 3-pole 0-100A I-Line Breaker 3W CT Kit 47" Frame 200:1 — —
539217G5-L 3-pole 125-225A I-Line Breaker 3W CT Kit 47" Frame 500:1 — —
539217G6-L 3-pole 250-400A I-Line Breaker 3W CT Kit 47" Frame 1000:1 — —
539217G7-L 1-pole 0-100A Branch Breaker CT Kit 200:1 — —

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 6
The PM4 Large Interface Board (PLIB) provides voltage and current attenuation for Square-D I-
Line panelboards. There are 42 CT locations on each LIB for a total capacity of eight 4-wire (3
phases and neutral) or 5-wire (3 phases, neutral and ground) breakers.
WARNING
Before connecting a large CT to the PLIB, note the CT MUST have a 1A secondary.
Connecting anything other than a 1A secondary CT will damage the PLIB and the CT.
To ensure the proper current ratio and accuracy, the CTs should be purchased through
Vertiv. See Table 1 for details. Contact your local Vertiv representative or call Vertiv
Support at 800-543-2378.
Two PLIBs are supplied for a total maximum monitoring capacity of sixteen 5-wire I-Line
and/or subfeed breakers.

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 7
3.4 Branch Circuit Monitoring Sensor Module (BSM)
The Branch Circuit Monitoring Sensor Module (BSM)—more commonly referred to as the CT
Module—contain 21, 27 or 36 individual Current Transformers filled inside an epoxy enclosure.
Each load circuit is passed through one of the openings for branch circuit current monitoring. The
signals leave the CT module via a ribbon cable which is connected directly to the PM4 Monitor
Board (PMB) for attenuation and processing.
There are two BSM designs depending on the manufacturer of the panelboard installed:
• Utilize 1" spacing between circuits.
• Utilize 3/4" spacing between circuits.
For larger panelboards, the CT Module is designed to interlock to maintain alignment between
the breaker poles and the CT Modules.
3.5 Power Supply With EMI Filter
The power supply assembly converts 100-240VAC (+10%/-13% range) 50/60Hz into 12VDC to
provide logic level power for the PMB.
The Power Supply is fed from the line side of the panelboard main breaker. If during normal
operation the panelboard main breaker trips or is turned off, the PMB will still have power to
communicate alarms via the local display or remotely via Liebert IntelliSlot®cards.
NOTE
The diameter of each CT hole is 0.433" (11mm). Wire diameter and thickness of insulation must be
taken into account before wiring each branch circuit. Using wire that is too large may prevent the
conductor from fitting through the CT hole. Do not attempt to alter the diameter of the CT
opening.

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 8
3.6 Human-Machine Interface/Display Assembly (Optional)
The LDMF allows users to view the panelboard circuit data locally through the optional display.
The user interface has function keys to scroll through and view each panelboard's data as well as
the associated branch circuits and/or subfeeds.
Along with the branch circuit data the LDMF Display also has an alarm annunciation window that
lists all active alarms. The display has an LED status indicator that changes to red in the event of
an alarm. The Silence/Reset button will silence the audible alarm when pressed once and held
until alarm is silenced. When pressed a second time, the button clears the alarm and turns off the
red LED.
Alarm thresholds cannot be added, deleted or adjusted on the local display. These functions may
be performed only by using the LDMF Configuration software, which is available for download at
the Liebert Web site. Refer to 5.3 - Downloading the Software for downloading instructions and
see 5.5 - Using the Configuration Tool for details on using the software.

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 9
3.7 PM4 Adapter Board
• The PM4 Adapter Board (PAB) is provided with each Liebert LDMF. The PAB is typically mounted on the
back of the display, which is located on the front door of the unit. The PAB provides a customer interface to
the LDMF summary alarm contacts.
• If two Liebert LDMF systems are provided, the two PABs are connected to each other at the factory. It is
only necessary to connect to one PAB to monitor the Customer Summary Alarm; the two Liebert LDMF
units share summary alarm contacts.
• On the Liebert FPC and Liebert PPC the PAB has additional connections on TB1 that include Remote
Emergency Power Off (EPO). The field-selectable switch S1 on the PAB allows the selection for either
Manual or Auto restart. The factory default setting is Manual.
• Manual restart allows for an orderly supervised startup after power failure. The control circuit
automatically energizes the shunt trip mechanism of the main input breaker upon sensing output voltage
failure.
• Setting the switch to Auto deactivates the manual restart. In Auto restart mode, the main input breaker
does not trip due to power failure and the unit will restart when power is restored.
NOTE
The TB1 connections for customer alarms 1 - 5 are used only with the VPMP product.

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 10
4.0 INSTALLATION
This section provides instructions for installing and connecting Liebert LDMF current
transformers. If any Liebert LDMF component requires service, contact Vertiv Support at
800-543-2378 for assistance.
4.1 Installing a BSM (CT Module Assembly)
In most cases the BSM—the CT Module—is factory-installed and no further work is required. If a
CT Module must be added, it attaches easily to the side of a panelboard to monitor any
combination of 1-, 2- and 3-pole circuit breakers.
• For side-by-side panelboards (21 circuits on each side), attach one CT Module
to each side of the panelboard, ensuring that the center of the CT hole lines up
to the branch circuit breaker connection.
• For Square-D Inline panelboards (42 circuits in a row), the two CT second, lower
CT Module so that the two cutout sections line up, then attach the screws to
secure the CT Modules to the panelboard.
• For GE Inline type panelboards, the two CT Modules fit end to end. Flip the
second, lower CT Module so that the 50-pin ribbon cable connector, mounted
on the bottom of the CT Module, lines up with the hole in the panelboard
mounting bracket.
Install the circuit breakers according to the manufacturer's
documentation. Route the circuit wire through the center of the CT and
attach securely to the circuit breaker.
4.1.1 Connecting Panelboards A and B
The CT Module connects to the PMB via a 50-pin ribbon cable attached
to the back of the CT Module. Route the ribbon cable and attach to the
appropriate connector (see figure at right).
There are four connectors that are labeled for easy identification: two for
Panelboard A (A1 and A2) and two for Panelboard B (B1 and B2).
• Connect the CT module that will monitor Circuits 1-21 to the A1 or B1
connector, depending on whether the CT Module is monitoring Panelboard A
or B.
• Connect the CT module that will monitor Circuits 22-42 to the corresponding A2 or B2 connector.
WARNING
Dangerous voltages exist in power distribution units and power conditioning units. To
ensure maximum safety, all circuits breakers in the panelboard should be removed of power
and the input feeder breaker should be turned Off and locked-out in accordance with NEC
and local/state code.
NOTE
Liebert LDMF components and any other monitoring devices should be installed only by properly
trained and qualified personnel.
Circuits
Monitored
Panelboard A
Connector
Panelboard B
Connector
1-21 A1 B1
22-42 A2 B2

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 11
To configure the branch circuits, refer to 5.5.11 - Add a Circuit Breaker.
4.2 Installing a Solid-Core Current Transformer
The CT for the panelboard main input circuit breaker is hard-wired to the connectors. Removing
CT wires from the connector requires a pin extraction tool.
Contact Vertiv Support at 800-543-2378 for assistance.
Typically the three-phase and neutral wires utilize a CT rating of 100:1, 200:1 500:1 or 1000:1, while
the ground wire utilizes a CT rating of 100:1.
Route the circuit wire through the core of the CT and wire-tie the CT to the cable. Refer to the
manufacturer's documentation for proper orientation to ensure accurate readings.
NOTE
• Panelboard A is either Panelboard 1 or Panelboard 3.
• Panelboard B is either Panelboard 2 or Panelboard 4 depending on which Liebert LDMF
Control Board is being configured.
WARNING
A solid-core CT cannot be installed on a wire while current is flowing through the wire.
Damage to the burden resistor and CT will occur. Power must be removed before installing
and/or removing any CT. CT’s should be installed only by properly trained qualified
electricians.
NOTE
When replacing or installing a CT, ensure that the replacement CT has a secondary rating of 1A—
for example, 100:1, 200:1, 500:1 or 1000:1. Using a higher-rated CT—for example, 100:5 or 500:5-
will damage the burden resistors on the PIB board.
NOTE
When installing CT’s for a large branch circuit breaker or subfeed, verify which monitoring board
is installed.
• A PIB can support up to three subfeeds,.
• One LIB can support up to eight output and/or subfeed breakers.
• Two LIB boards are provided to support up to 16 output and/or subfeed breakers.
LO
TNU
MBER
INSTRUMENTS



 




Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 12
4.3 Installing a Current Transformer on the PIB Interface Board
If subfeed breakers are ordered with the unit, the phase,
neutral and ground CTs are wired to the Interface
Board.The CTs will be zip-tied inside the equipment for the
electrician to install on each conductor when the
conductors are wired to the subfeed/large branch breaker.
The ground and neutral CTs for each factory-supplied
subfeed or large breaker are factory-installed and wired.
CTs have a white or H1 that depicts how to position the CT
on the cable to ensure accurate readings. The white dot or
H1 must face toward the source when installing the CT on
the phase cables. The neutral conductor CTs are placed in
the opposite direction, with the marking faced toward the load. Route the conductors through the
core of the CTs and wire-tie the CT to the cable to ensure the CT stays in place.
If subfeed breakers are installed in the field, up to five CTs may be installed (three phases, neutral
and ground). The neutral and ground CTs may be omitted if monitoring of neutral and ground is
not required. The 5-wire CT kits will be shipped separately and grouped together with each CT
with a label indicating whether it is a phase CT, neutral CT or ground CT.
There are two 18-pin terminal blocks on the Interface Board for large branch circuit breakers
and/or subfeeds-one for Panelboard A and one for Panelboard B.
The circuit board is marked with a triangle to indicate Pin 1. Pin 1 should be used for the white wire
of CT1 (Phase A). The black wire should be connected to Pin 2. The same pattern will follow for
the remaining CTs.
After all CTs are installed, use the Configuration tool to label and set alarm parameters. To
configure the Liebert LDMF, see 5.5.11 - Add a Circuit Breaker.
If the Power Distribution Center is supplied with optional isolated ground, the isolated ground
circuit can be monitored by the Liebert LDMF. Usually the CT is already installed and wired to the
Large Branch Terminal Block at the factory. If not, perform the following steps:
(For Isolated Ground CT Installation only)
• Connect the isolated ground CT to Pins 17 and 18 on the two 18-pin terminal blocks on the Interface
Board.
• Connect the isolated ground CT white wire to Pin 17 and the CT black wire to Pin 18.
Refer to the following example and Table 2 for wiring configuration details.
Example: When installing a subfeed breaker where the three phases, neutral and ground will be
monitored, the CTs should be wired as follows:

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 13
If a second subfeed or large branch breaker will be installed, the same pattern will continue. Pins
11 and 12 will be Phase A CT for the second breaker, Pins 13 and 14 will be Phase B CT and so on.
Table 2 Large branch breaker CT wiring
Pin Wiring
1PhaseACT White
wire
2 Phase A CT Black wire
3PhaseBCT White
wire
4 Phase B CT Black wire
5PhaseCCT White
wire
6 Phase C CT Black wire
7NeutralCT White
wire
8 Neutral CT Black wire

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 14
Table 3 CT Table for Interface Board
Configuration 1: Four Modules
Connector P3 (A)
Position 9 • 8 • 7 • 6 • 5 • 4 • 3 • 2 • 1 •
WireColor B W BWBWBWBWBWBWBWBW
CT CT9 or IG CT8 CT7 CT6 CT5 CT14 CT3 CT2 CT1
Connector P4 (B)
Position 9•8•7•6•5•4•3•2•1•
WireColor B W BWBWBWBWBWBWBWBW
CT CT18 or IG CT17 CT16 CT15 CT14 CT13 CT12 CT11 CT10
Configuration 2: Two Modules With Large Branch Breaker CT’s
Connector P3 (A)
Position 9 • 8 • 7 • 6 • 5 • 4 • 3 • 2 • 1 •
WireColor B W BWBWBWBWBWBWBWBW
CT LB9 or IG LB8 LB7 LB6 LB5 LB4 LB3 LB2 LB1
Connector P4 (B)
Position 9•8•7•6•5•4•3•2•1•
WireColor B W BWBWBWBWBWBWBWBW
CT LB18 or IG LB17 LB16 LB15 LB14 LB13 LB12 LB11 LB10
Configuration 3: Four Modules With Two 5-Wire Subfeed Breaker CT’s
Connector P3 (A)
Position 9 • 8 • 7 • 6 • 5 • 4 • 3 • 2 • 1 •
WireColor B W BWBWBWBWBWBWBWBW
CT LB5 LB4 LB3 LB2 LB1
Phase IG G1 N1 C1 B1 A1
Connector P4 (B)
Position 9 • 8 • 7 • 6 • 5 • 4 • 3 • 2 • 1 •
WireColor B W BWBWBWBWBWBWBWBW
CT LB10 LB9 LB8 LB7 LB6
Phase IG G2 N2 C2 B2 A2
Configuration 4: Four Modules With Three 5-Wire Subfeed Breaker CT’s
Connector P3 (A)
Position 9 • 8 • 7 • 6 • 5 • 4 • 3 • 2 • 1 •
WireColor B W BWBWBWBWBWBWBWBW
CT LB12 LB11 LB5 LB4 LB3 LB2 LB1
Phase IG G3 N3 G1 N1 C1 B1 A1
Connector P4 (B)
Position 9 • 8 • 7 • 6 • 5 • 4 • 3 • 2 • 1 •
WireColor B W BWBWBWBWBWBWBWBW
CT LB13 LB12 LB11 LB10 LB9 LB8 LB7 LB6
Phase IG C3 B3 A3 G2 N2 C2 B2 A2

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 15
Configuration 5: Four Modules With Six 3-Wire Subfeed Breaker CT’s
Connector P3 (A)
Position 9 • 8 • 7 • 6 • 5 • 4 • 3 • 2 • 1 •
WireColor B W BWBWBWBWBWBWBWBW
CT LB9 LB8 LB7 LB6 LB5 LB4 LB3 LB2 LB1
Phase C3 B3A3C2B2A2C1 B1 A1
Connector P4 (B)
Position 9 • 8 • 7 • 6 • 5 • 4 • 3 • 2 • 1 •
WireColor B W BWBWBWBWBWBWBWBW
CT LB18 LB17 LB16 LB15 LB14 LB13 LB12 LB11 LB10
Phase C6 B6A6C5B5A5C4B4A4
Configuration 6: Three Modules With Nine Large Branch Breaker CT’s
Connector P3 (A)
Position 9 • 8 • 7 • 6 • 5 • 4 • 3 • 2 • 1 •
WireColor B W BWBWBWBWBWBWBWBW
CT LB9 or IG LB8 LB7 LB6 LB5 LB4 LB3 LB2 LB1
Phase C3 B3A3C2B2A2C1 B1 A1
Connector P4 (B)
Position 9 • 8 • 7 • 6 • 5 • 4 • 3 • 2 • 1 •
WireColor B W BWBWBWBWBWBWBWBW
CT C6 B6 A6 C5 B5 A5 C4 B4 A4
W = White
B = Black
IG = Isolated Ground CT
LB = Large Branch Breaker CT
A = A Phase CT
B = B Phase CT
C = C Phase CT
N = Neutral CT
G = Ground CT
Table 3 CT Table for Interface Board (continued)

Vertiv™|Liebert® LDMF™ Distribution Monitoring User Manual | 16
4.4 Connecting a Current Transformer to the PM4 Large Interface Board
(PLIB)
PLIB can monitor eight 4-wire or 5-wire output/subfeed breakers. Two LIB boards are provided to
support up to 16 output and/or subfeed breakers. If subfeed breakers are ordered with the unit,
the phase CTs are installed and wired to the PLIB. The neutral and ground CTs are also factory-
supplied and wired to the PLIB as required.
CTs have a white dot or H1 marking that depicts how to position the CT to ensure accurate
readings. The white dot or H1 marking must face toward the load when installing the CT on the
ground and neutral cable. The phase CT's are placed in the opposite direction, with the marking
faced toward the source. Route the neutral and ground cable through the core of the specified CT
and wire-tie the CT to the cable.
If subfeed breakers are installed in the field, up to five CTs may be installed to monitor a subfeed
breaker (three phases, neutral and ground). The neutral and ground CTs may be omitted if
monitoring of neutral and ground is not required.
The designators on the PLIB are different from those on the Interface Board.
• CT1 (Phase A white wire) begins on TB1 CT1+ and the black wire connects to CT1-.
• The Ground CT for the first subfeed/output circuit breaker connects to TB4 CT35.
The designators on the PLIB are different from those on the Interface Board.
• CT1 (Phase A white wire) begins on TB1 CT1+ and the black wire connects to CT1-.
• The Ground CT for the first subfeed/output circuit breaker connects to TB4 CT35.
If more output or subfeed CTs must be installed, continue in the same pattern shown above.
• Connect the Phase A CT for the second breaker on CT5 (white wire to CT5+, black to CT5-).
• Connect the Ground CT for the second breaker to CT36 (white wire to CT36+, black to CT36-).
• Continue the same pattern until all CT connections are used or there are no more outputs or subfeed CTs
to add.
First Breaker Second Breaker
CT1+ Phase A CT White wire CT5+ Phase A CT White wire
CT1 Phase A CT Black wire CT5 Phase A CT Black wire
CT2+ Phase B CT White wire CT6+ Phase B CT White wire
CT2 Phase B CT Black wire CT6 Phase B CT Black wire
CT3+ Phase C CT White wire CT7+ Phase C CT White wire
CT3 Phase C CT Black wire CT7 Phase C CT Black wire
CT4+ Neutral CT White wire CT8+ Neutral CT White wire
CT4 Neutral CT Black wire CT8 Neutral CT Black wire
CT35+ Ground CT White wire CT36+ Ground CT White wire
CT35 Ground CT Black wire CT36 Ground CT Black wire