VEVOR 150W PGL-C1 User manual

150W PGL-C1/200W PGL-G1
300W PGL-X1/400W PGL-Z1
LED GROW LIGHT

Have product questions? Need technical suppo? Please feel free to contact us:
CustomerSe[email protected]
NEED HELP? CONTACTUS!
This is the original instruction, please read all manual instructions carefully before
operating. VEVOR resees a clear interpretation of our user manual. The appear-
ance of the product shall be subject to the product you received. Please forgive us
that we won't inform you again if there are any technology or software updates
on our product.
LED GROW LIGHT
01

02
Please read this manual carefully before using the product.
Notes before Installation
1、Be careful to open the caon, and contact us if there is any damage.
2、Non-professional technicians, please do not repair or modify this
product without authorization.
3、Please turn o the power before installation to avoid improper
operation.
4、To ensure the lifetime of the product, please do not use it in a place
with strong acid mist.
5、Please check whether the voltage marked on the luminaire is consis-
tent with the input voltage to be connected, so as not to damage the
LED luminaire.
6、Make sure the installation position can withstand 10 times the
weight of the luminaire before installation and install it at a at place
without vibration, no swing, and no re hazard.
7、Type X connection: (refers to the power cord that can be separated
and replaced by the user)
If the supply cord is damaged, it must be replaced by a special cord
or assembly available from the manufacturer or its seice agent.
This device complies with Pa 15 of the FCC Rules.Operation is subject to the
following two conditions:(1)This device may not cause harmful inteerence, and
(2)this device must accept any inteerence received,including inteerence that may
cause undesired operation.
Acceptable For Indoor Use only.
The luminaire shall be positioned in such a way that prolonged gazing at
the luminaire is not permitted.

03
Installation Instruction
1. Hanging the lamp on the ceiling or other secure places with
lifting rope.
2. Connecting the plug to the socket,connect the plug to the
power source.
AC 100-277V

04
3. Choosing dimmer knob ：There are a total of 5 gears,
25%/50%/75%/100% four brightness gears,one RJ control gear. Just
rotate the appropriate brightness gear according to the actual usage.
4. When the dimmer gear switch is set to EXT/OFF, it switches to the
RJ po dimmer function, and you can adjust the brightness through
the RJ controller.
RJ po
0-10V DIMMING
25
%
0
5
0%
75
%
100%
E
X
T
/
O
F
F
25
%
0
5
0%
75
%
100%
E
X
T
/
O
F
F
Note: This suggestion is for reference only, and can be freely adjusted according
to the actual situation.
Set at high power of LED and high away from the plant, it covers more area.
Or set to a lower power and close to the plant, it covers less but is more eco-friendly.
Application

05
1、Humidity：≤95%.
2、Air Pressure：90-106 Kpa
1、1 x LED Grow Light
2、1 x Installation Instruction
3、2 x Lifting Ropes
4、1 x Plug
5、2 x Hook
6、2 x Stopper
It is professionally used for hemp/cannabis/Marijuana lighting.
Connect the plug to the power source
Input Voltage：AC100-277V
Power Cord：
Application
Electrical Parameter
Application Environment
Package
Photosynthesis
Output Spectrum Test Repo

Shipping and Warehousing
Product recove
1、Please do not shake it too much during transpoation, handle it
carefully when unloading.
2、Recommended being stored in a warehouse of -10 to 60℃ and keep
the warehouse d.
This product is subject to the provision of European Directive 2012/19/EC. The
symbol showing a wheelie bin crossed through indicates that the product requires
separate refuse collection in the European Union. This applies to the product and all
accessories marked with this symbol. Products marked as such may not be discard-
ed with normal domestic waste, but must be taken to a collection point for recycling
electrical and electronic devices.
Impoer: WAITCHX
Address: 250 bis boulevard Saint-Germain 75007 Paris
Impoer: FREE MOOD LTD
Address: 2 Holywell Lane, London, England, EC2A 3ET
EUREP UK LTD
UNIT 2264, 100 OCK STREET, ABINGDON
OXFORDSHIRE ENGLAND OX14 5DH
UK REP
EUREP GmbH
Unterlettenweg 1a, 85051 Ingolstadt,
Germany
Made in China
EC REP
Manufacturer: SLT Lighting Technology (Dongguan) Co.,Ltd.
Address:No.201,2nd Floor, 2BLDG,Gongchang Road 353, Huangjiang Town,
Dongguan City, Guangdong, China.

E-mail: CustomerSe[e-mail]