Viatek LL03-QUATRO User manual

LL03-QUATRO
(Red/Green Double Coverage Laser)

IMPORTANT SAFEGUARDS
To reduce the risk of re, electric shock, or injury when using any electric
appliance, precautions should be made. These precautions include but are
not limited to:
Read all instructions.
CAUTION! — Use only as directed. Improper use may result in damage to the
eyes due to direct exposure to laser radiation.
This product has a polarized plug to reduce the risk of electric shock. It
will therefore only t into a polarized outlet one way. If the plug does not t,
reverse the plug. If it still does not t, contact a qualied electrician. Do not
use with an extension cord unless the plug can be fully inserted. Do not alter
the plug.
This unit is certied as a Class IIIa laser product by the US Federal Laser
Product Performance Standard (FLPPS) according to regulations in 21 CFR
Subchapter J. Class IIIa laser products can be hazardous when directly
viewed.
Avoid looking directly into Class IIIa lasers. This product, as well as other
demonstration laser products like some laser pointers, are classied as
Class IIIa laser energy levels. This product uses diractive optics to scatter
the beam of energy. This scattering eect causes the energy concentration
to drop below the exposure limits for momentary or accidental viewing at
a relatively short distance from the laser aperture. As with all bright light
sources, when you operate this device in public areas it is recommended that
up-close access to the light be restricted.
While the Class IIIa laser in this device may be hazardous on its own, it is
encased in a protective housing and uses diractive holographic optics,
therefore users are not directly exposed to laser radiation during operation or
maintenance. Each individual laser beam is less than 5mW, which is about
the same as an average laser pointer.
DO NOT attempt to open the protective housing or operate the device if
the aperture windows are damaged. If the unit requires service that involves
removing the protective housing, contact the manufacturer. Opening the
protective housing voids the warranty.
Use only three-wire outdoor extension cords that have three-prong grounding
plugs, plugged into grounded outlets. Acceptable extension cord types:
SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW,
SJW-A, SJOW, SJOW-A, SJTW, SJTW-A, SJTOW, SJTOW-A
Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the
circuit(s) or outlet(s) to be used while operating portable laser light in a wet
location. Receptacles with built-in GFCI protection are available for this
purpose.
SAVE THESE INSTRUCTIONS

Assembly
Screw the ground stake or mounting plate into the bottom of the light
projector clockwise until tight (g. 1). To adjust the angle of the light
projector, loosen the pivot clamp screw by turning it counterclockwise.
Once the angle adjustment is made, twist the pivot clamp screw
clockwise until tight to secure (g. 2).
Plug the 2-prong adapter into the
power supply transformer. Screw
on the weather-resistant cap tightly
to help protect the connection from
weather.
The mounting plate can be attached
to a wooden structure such as a
deck using 4 screws (not included).
The unit can be detached from the mounting plate without
removing the entire assembly simply by unscrewing the unit
counterclockwise.
IMPORTANT: Point Night Stars directly at your home and never point Night Stars directly into
the sky. Do not project Night Stars at or within the ight path of an aircraft within 10 nautical
miles of an airport. If the surface at which you intend to point the Night Stars laser is within 10
nautical miles of an airport, lower the angle so that it does not point into the sky. Do not point
laser light toward oncoming pedestrians, vehicles, or trafc routes on land, sea, or air.
Operation
Press the button on the back of the laser unit to choose between red laser, green laser, dual-
colored laser, or o.
Daily Timer
The laser light has an automatic, built-in timer that turns the unit on for 6 hours and shuts o for
18 hours each day. This timer cycle begins when the laser is turned on and resets each time the
laser is turned o and then on again. Unplugging the laser will also reset the timer.
Notes:
� Only use supplied transformer connected to a properly grounded outdoor outlet.
� Do not use with dimmers.
� Operate in temperatures of -4˚F to 86˚F. There may be a slight delay if operating below 55˚F.
Please allow up to 10 minutes for light to warm up and reach its full projection. Green laser
startup time may take up to 30 minutes in temperatures below 14˚F.
� When hanging the laser light with equipment other than what is included, for safety purposes
it is recommended to mount using a sturdy hanging clamp and safety cable.
Ground Stake
Light Projector
2-Prong
Adapter
Weather-Resistant Cap
Pivot Clamp
Screw
Fig. 1
Fig. 2
Mounting Plate

Read Instructions
Before Operating MADE IN
CHINA
© 2016 VIATEK CONSUMER PRODUCTS GROUP, INC. All specifications are subject to change without notice. All rights reserved.
For customer service call 888.7.VIATEK (+1.423.402.9010 for outside the United States) or visit us online at viatekproducts.com
Pour le service a la clientele appelez le 888.7.VIATEK (+1.423.402.9010 a l'extérieur des États-Unis) ou visitez viatekproducts.com
Para servicio al consumidor llame al 888.7.VIATEK (fuera de Estados Unidos marque +1.423.402.9010) o visite viatekproducts.com
PATENT PENDING
REV-Model No.
DO NOT DISPOSE OF BATTERIES IN FIRE. ALWAYS DISPOSE OF BATTERIES PER LOCAL & FEDERAL GUIDELINES
Follow Us
Like Us
Viatek Site
Viatek Consumer Products Group, Inc. 6011 Century Oaks Dr. Chattanooga, TN 37416
011116LL03-QUATRO
Product Specications
Laser Classication
Maximum Laser Power
Laser Wavelength
Laser MTBF
Power Consumption
Power Input
Operation
Operating Temperature
Maintenance
Warranty
Class IIIa
(Single beam) Less than 5mW
Green: 532nm / Red: 660nm
More than 5000 hours
Up to 19 watts
120VAC (when used with supplied transformer)
Indoor / Outdoor
-4˚F to 86˚F
Maintenance free — no user serviceable parts
Limited 1-year warranty