Vicon Pilot Lite V1522 User manual

Vicon Part No. 8009-8196-00-01 Rev 1008 Section 2
XX196-00-01
V1522 MATRIX SWITCHING
AND CONTROL SYSTEM
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your
requirements or that the operation will be entirely error free or perform precisely as described in the
documentation. This system has not been designed to be used in life-critical situations and must not
be used for this purpose.
Copyright © 2008 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: 44/(0) 1489-566300 WEB: www.vicon-cctv.com

Important Safeguards – Indoor Use
GRAPHIC SYMBOL EXPLANATION
The lightening bolt symbol alerts the user to the presence of
dangerous voltage that may present the risk of electric shock.
The exclamation point symbol alerts the user to the presence of
important operating and maintenance instructions.
WARNING
To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
1. Read Instructions - Read all safety and operating instructions
before the product is operated.
2. Retain Instructions - Retain all safety and operating
instructions for future reference.
3. Heed Warnings - Pay attention to all product warnings.
4. Follow Instructions - Follow all operating instructions.
5. Cleaning -(Do not use caustic, abrasive or aerosol
cleaners)
a) For units that CAN BE DISCONNECTED from the power
source, use a damp cloth for cleaning.
b) For units that CANNOT BE DISCONNECTED from the
power source, use a damp cloth for cleaning and do not
allow moisture or liquids to enter vents.
6. Attachments - Use only UL Listed Vicon recommended
attachments to prevent unit damage and personal injury.
7. Water and Moisture - Use only products designed for outdoor
environments where they will be exposed to water or moisture.
8. Accessories - Do not place the unit on an unstable surface to
avoid falling. Use only UL Listed Vicon recommended mounting
accessories.
9. Ventilation - Do not block ventilating slots and openings as
they ensure reliable operation. Do not place the unit near a heat
source or into an enclosure unless recommended by Vicon.
10. Grounding - Only products equipped with a 3-prong
grounded plug should be inserted into a grounded power outlet.
Contact an electrician to replace an obsolete outlet. Do not force
a plug into a non-grounded outlet.
11. Power Cord Protection - Power supply cords should not be
routed in trafficked areas or in tight spaces where they will be
pinched or used to bear weight. Allow some slack in the cord
where it enters the unit.
12. Lightning - Disconnect the product from its power source and
cable system when possible to prevent damage due to lightning
and power-line surges.
13. Power Lines - Do not locate outside cables over power or
utility lines where they can fall and make direct contact. Contact
with power lines can be fatal.
14. Overloading - Do not overload wall outlets and extension
cords to prevent risk of fire and electric shock.
15. Object and Liquid Entry - Never probe through, or spill liquid
into, enclosure openings to prevent risk of fire or electric shock.
16. Servicing - Refer all servicing to qualified service personnel.
17. Damage Requiring Service - Obtain service when:
a) The power-supply cord or plug is damaged.
b) Objects have fallen or liquid has been spilled into the
product.
c) The product is not designed for outdoor use and has been
exposed to water or moisture.
d) The product does not operate per the operating instructions.
Perform Vicon recommended adjustments, modifications
and troubleshooting only to avoid unit damage and personal
injury.
e) The product has been dropped.
f) The product shows a significant change in performance.
18. Replacement Parts - Use only Vicon specified replacement
parts or an approved equivalent to prevent unit damage and
injury.
19. Safety Check - Request safety checks to be performed
following repair or maintenance to verify proper operation.
20. ESD Precaution - Take all normal electrostatic discharge
precautions to avoid component damage during installation and
operation.
21. For 230 VAC Devices Only - When the disconnect device is
not incorporated in the equipment or when the plug on the power
supply is intended to serve as the disconnect device, follow the
guidelines below:
a) For permanently connected 230 VAC units, a readily
accessible disconnect device must be incorporated into the
site wiring.
b) For 230 VAC units with a plug, the outlet must be installed
near the unit and be easily accessible.

FCC Notice
Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart
B for a Class A digital device.
WARNING
This equipment generates and uses radio frequency energy and if not installed and used
properly, that is, in strict accordance with the manufacturer’s instruction, may cause interference
to radio and television reception. It has been type tested and found to comply with the limits for a
Class A computing device in accordance with the specification in subpart B of part 15 of the FCC
rules, which are designed to provide reasonable protection against such interference in a
commercial installation. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio and television reception,
which can be determined by turning equipment off and on, the user is encouraged to try and
correct the interference by one or more of the following measures:
•Reorient the receiving antenna.
•Relocate the equipment with respect to the receiver.
•Relocate the equipment away from the receiver.
•Plug the equipment into a different electrical outlet so that the equipment
and receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions.
The user may find the following booklet prepared by the Federal Communications Commission
helpful:
“Interference Handbook, Bulletin CIB-2”
This booklet is available from the U.S. Government Printing Office, Superintendent of Documents,
Mailstop SSOP, Washington, D.C. 20402-9328, ISBN 0-16-045542-1.
Warning: Power must be removed from this unit before removing circuit modules or cables.
Caution: This unit contains circuit cards with integrated circuit devices that can be damaged
by static discharge. Take all necessary precautions to prevent static discharge

Table of Contents
Chapter 1 Introduction...................................................................................................................1-1
General Information ...................................................................................................................1-2
System Capabilities .............................................................................................................1-3
Organization of this Manual .......................................................................................................1-4
Glossary.....................................................................................................................................1-5
Chapter 2 Installation and Operation............................................................................................2-1
Installation..................................................................................................................................2-2
Unpacking............................................................................................................................2-2
Installing the Unit .................................................................................................................2-3
Attaching the Tilt Stand..................................................................................................2-3
Attaching the Mounting Ears and Handles.....................................................................2-4
Connections and Wiring.......................................................................................................2-5
Camera Connection.......................................................................................................2-6
Monitor Connection........................................................................................................2-7
Keypad Connection .......................................................................................................2-8
Receiver Connection......................................................................................................2-9
Alarm Inputs.................................................................................................................2-10
Alarm Relay Output......................................................................................................2-12
Relay/Audio Switcher (AUDIOSWITCH)......................................................................2-13
Operation.................................................................................................................................2-14
Front Panel ........................................................................................................................2-14
Control Keys................................................................................................................2-14
Function Keys..............................................................................................................2-15
LCD Display.................................................................................................................2-16

iv | Table of Contents
Joystick........................................................................................................................2-17
Other Controls and Connectors...................................................................................2-17
Powering the Unit On.........................................................................................................2-17
Navigating the User Interface.............................................................................................2-18
Linux Operating System Functions..............................................................................2-19
Accessing the Operating System Online Help.............................................................2-19
Operating System Root Password...............................................................................2-20
Changing System Time and Date................................................................................2-21
Shutdown.....................................................................................................................2-22
Chapter 3 Configuration................................................................................................................3-1
Navigating the Configurator .......................................................................................................3-2
Menu Bar .............................................................................................................................3-2
File.................................................................................................................................3-3
Saving a Database Configuration...............................................................................3-4
Pilot Application.............................................................................................................3-4
Edit ................................................................................................................................3-5
Admin.............................................................................................................................3-5
Video Switch Setup........................................................................................................3-6
Keypads.........................................................................................................................3-7
Cameras........................................................................................................................3-7
Monitors.........................................................................................................................3-8
Alarms............................................................................................................................3-8
Tools..............................................................................................................................3-9
Help ...............................................................................................................................3-9
Toolbar...............................................................................................................................3-10
System Summary...............................................................................................................3-11
Creating a Database................................................................................................................3-12
Creating a Configuration..........................................................................................................3-13
Keypads.............................................................................................................................3-14
Keypad Groups............................................................................................................3-16
Keypad/Monitor Partitions............................................................................................3-16
Cameras ............................................................................................................................3-17

Table of Contents | v
Preset Titles.................................................................................................................3-19
Camera Partitions........................................................................................................3-20
Monitors.............................................................................................................................3-21
TDT Position................................................................................................................3-24
Alarms................................................................................................................................3-30
Common Stack Mode Example ...................................................................................3-32
Independent Stack Mode Example..............................................................................3-34
First Available Alarm Mode Example...........................................................................3-36
Alarm Action ................................................................................................................3-38
Receiver Action............................................................................................................3-40
Alarm Input Controls....................................................................................................3-42
Video Switch Setup............................................................................................................3-45
Sequential Tour ...........................................................................................................3-45
Salvo Switch................................................................................................................3-50
Default Callup Values ..................................................................................................3-51
Assign Dial Up Numbers – Dial Up Salvo....................................................................3-52
Assign Dial Up Numbers – Dial Up Tour......................................................................3-53
Assign Dial Up Numbers – Dial Up Camera ................................................................3-54
Camera/Monitor Partitions...........................................................................................3-54
Administration....................................................................................................................3-55
Host Port......................................................................................................................3-55
Timed Events...............................................................................................................3-57
Triggered Events .........................................................................................................3-69
Partitioning.........................................................................................................................3-75
Keypad/Monitor Partitions............................................................................................3-75
Camera Partitions........................................................................................................3-76
Camera/Monitor Partitions...........................................................................................3-78
Tools..................................................................................................................................3-79
Serial Ports..................................................................................................................3-79
Global Settings ............................................................................................................3-81
Database Log ..............................................................................................................3-83

vi | Table of Contents
Chapter 4 Maintenance..................................................................................................................4-1
Introduction................................................................................................................................4-2
Fuse Replacement.....................................................................................................................4-3
Storage ......................................................................................................................................4-4
Cable Recommendations...........................................................................................................4-5
Video Cabling.......................................................................................................................4-5
Materials........................................................................................................................4-5
Cable Types...................................................................................................................4-5
Video Control Cabling....................................................................................................4-6
Twisted-Pair Cable...............................................................................................................4-7
Materials........................................................................................................................4-7
Cable Types...................................................................................................................4-7
Cable Suppliers .............................................................................................................4-8
Shipping Instructions..................................................................................................................4-9
Technical Specifications...........................................................................................................4-10
Electrical............................................................................................................................4-10
Video..................................................................................................................................4-10
Mechanical.........................................................................................................................4-11
Environmental....................................................................................................................4-11

Table of Contents | vii
Trademarks
Vicon, its logo, Vicoax and Pilot Lite are registered trademarks or trademarks
of Vicon Industries Inc.
Linux is a registered trademark of Linus Torvalds.
Gnome is a trademark of The GNOME Project.
Slo-Blo is a registered trademark of Littelfuse.
Belden and Datalene are registered trademarks of Belden Inc.

viii | Table of Contents

General Information | 1-1
Pilot Lite XX196-00
1
Chapter 1
Introduction
This chapter provides general information about the Pilot Lite.
The chapter consists of the following topics:
Topic Page
General Information 1-2
Organization of this Manual 1-4
Glossary 1-5

1-2 | Chapter 1 Introduction
XX196-00 Pilot Lite
General Information
The Vicon® Pilot Lite™ V1522 Matrix Switching and Control System provides
control of CCTV systems of up to 32 cameras by 8 monitors. Everything you
need to connect cameras, monitors, keypads, receivers and alarms is
contained in a single unit. Programming the system is accomplished using
the built-in Configurator.
The Configurator provides an intuitive graphical user interface that enables
you to set up system parameters, such as:
Timed or Triggered Event Programming
Keypad Setup
Receiver Profile Configuration
Camera Setup
Titling and Identification of Cameras, Monitors and Presets
Monitor Setup
Salvo and Tour Configuration
Alarm Processing Configuration
The Pilot Lite has been configured with system defaults that should satisfy
most installations with no need for further customization. For many users, it
might not be necessary to modify the configuration with the Configurator.

General Information | 1-3
Pilot Lite XX196-00
Manual and sequential switching options are supported, including ascending
order and random order switching. Full camera-monitor partitioning and up to
32 timed events may be programmed. Default camera-monitor assignments
or a default tour may be programmed for power-on system startup after a
power outage.
Switching modes also include salvo or zone switching and sequencing
salvos, with up to eight camera-monitor pairs per salvo. These may be
selected manually or automatically. Salvos may be called up manually or by
alarm. Each salvo can have a unique combination of camera, monitor, and
preset position.
The Pilot Lite also provides touch-sensitive front panel controls with an
integral keypad and LCD display. Many common operations can be
performed using the front panel controls.
System Capabilities
The Pilot Lite supports the following:
32 Cameras
8 monitors
32 Receivers for PTZ control
9 Keypads (including the Pilot Lite front panel keypad)
32 Alarms
Descriptive titling and time and date for cameras or locations
Alarm prioritizing
32 Tours
89 Presets for PTZ cameras
24 Salvos
Host computer interface
6 Different Timed Event types
3 Triggered Event types

1-4 | Chapter 1 Introduction
XX196-00 Pilot Lite
Organization of this Manual
Chapter Description
2 Installation and Operation: Describes how to install the
Pilot Lite and operation instructions, including a
description of navigating the Linux® operating system
3 Configuration: Describes how to create custom profile for
your system.
4 Maintenance: Describes basic system maintenance,
reference information, shipping instructions and technical
specifications for the system.

Glossary | 1-5
Pilot Lite XX196-00
Glossary
Term Description
Alarm Interface A device that senses a change in status from an alarm
input and communicates that information to the Pilot
Lite.
FIFO First In, First Out. Applicable to alarms and how they
are handled by the system.
Keypad Input device used to control cameras, monitors and
other system actions.
NTSC National Television System Committee video format
standard used in the United States and other Western
Hemisphere countries.
PAL Phase Alternating Line video format standard used in
many European countries.
Preset A set of programmed pan, tilt and/or zoom actions that
are executed by a single command.
Receiver A device used to communicate with PTZ cameras and
Pan and Tilt devices. PTZ dome cameras have built-in
receivers.
Salvo Simultaneous display of video from various camera
stations on various monitors.
Stack A list of active alarms.
Tour Series of preprogrammed video displays from various
camera stations on a monitor.
V-Sync Vertical synchronization refers generally to the
synchronization of frame changes with the vertical
blanking interval. One camera is set up as a reference
and all other cameras are synched to it so that all
vertical sync signals form all cameras are aligned.
When the V-Sync is set to On, the video will switch
during the vertical interval sp that picture roll will not
occur.

1-6 | Chapter 1 Introduction
XX196-00 Pilot Lite

Installation | 2-1
Pilot Lite XX196-00
2
Chapter 2
Installation and Operation
This chapter provides installation and operation information for the Pilot Lite.
The chapter consists of the following topics:
Topic Page
Installation 2-2
Operation 2-14

2-2 | Chapter 2 Installation and Operation
XX-196-00 Pilot Lite
Installation
Caution:
This system should only be installed by a qualified technician using common
hand tools and approved materials and wiring methods in accordance with
the National Electrical Code ANSI/NFPA 70, state and local wiring codes. All
interconnecting equipment or accessories must be UL Listed. Any mention in
this manual of alarm inputs/outputs have not been evaluated by UL to be
used for burglar alarm functionality.
The Pilot Lite may be rack mounted or can be set on a desk or shelf. A tilt
stand may be attached to the mounting feet to tilt the unit up on a desk or
shelf. Rack mounting brackets are supplied with the Pilot Lite Accessory Kit.
Unpacking
Carefully open the carton. Remove the Accessory Kit and the unit from the
box and place them on a large, flat working surface. Open the Accessory Kit
and verify the hardware contained in the kit against the following table.
Vicon Part Number Description (Qty) Purpose
1298530501 Mounting Ears,
V1522ADVS (2) For rack mounting the unit.
1298531301 Handles V1522ADVS
(2) For mounting on front panel, to grip unit when sliding in or out of a rack.
8003736101 SCR 8-32 X 1/2 FLT HD
100 DEG SS (4) Used to mount the handles to unit after mounting ears have been installed.
8003733401 SCR 10-32 X 3/8 100
DEG FLT HD PH BLK
(8)
Used to mount the mounting ears to the unit.
F004802505 3-Position Male
Connector (1) Used to connect wiring to the Alarm Relay terminal block.

Installation | 2-3
Pilot Lite XX196-00
Vicon Part Number Description (Qty) Purpose
F004802508 6-Position Terminal
Block Plug (2) Used to connect wiring to Keypad and Receiver terminal blocks.
S56G0000004 16-Pin Terminal Block
(4) Used to connect wiring to Alarm 1-16 and Alarm 17-32 terminal blocks.
1291304205 Tilt Stand and Feet Kit Mounts to bottom of unit to enable upward tilt for
easier viewing.
8000811801 Bumper Feet (2) Self-adhesive rubber feet that attach to bottom
rear of unit when it is set on a desk or shelf.
1240557901 Optical Wheel Mouse Used for navigating the unit's user interface and
Configurator software.
1240547703 104-Key USB Keyboard Used to navigate and input data to the unit's
user interface and Configurator software.
1806524903 3-conductor Line Cord,
115 VAC Used to connect the unit to 115 VAC power.
11806524902 3-conductor Line Cord,
220 VAC Used to connect the unit to 220 VAC power.
F001730201 Fuse 0.75A, 5 X 20MM
250V Slo-Blo® (1) Replacement fuse.
V75TR-SHD 75 Ohm Terminator Used to terminate the D-Shell Looping
connectors on the rear panel.
Installing the Unit
The following paragraphs provide instructions on attaching the tilt stand if you
are desk or shelf mounting it and attaching the mounting ears and handles if
you are rack mounting it.
Refer to the Maintenance chapter, Technical Specifications section for
dimensions and weight.
Attaching the Tilt Stand
The tilt stand is used to elevate the front panel of the unit for better viewing
when mounted on a desk or a shelf. Bumper feet are used for the rear of the
unit. To install the tilt stand and bumper feet, select the following from the
Accessory Kit:

2-4 | Chapter 2 Installation and Operation
XX-196-00 Pilot Lite
Tilt Stand and Feet Kit 1291304205
Bumper Feet 8000811801
1. Locate the screw holes on the underside of the unit.
2. Line up the right mounting foot shown below with the screw holes and
attach it to the unit with the supplied hardware.
3. Insert one end of the tilt stand into the groove of the installed right
mounting foot. Insert the other end of the tilt stand into the left mounting
foot and position the left mounting foot over the left set of screw holes.
Attach it to the unit with the supplied hardware.
4. Remove the adhesive backing from the bumper feet and attach them
approximately 12 inches apart and approximately 1 inch from the rear
panel.
Attaching the Mounting Ears and Handles
The mounting ears are used to attach the unit to a rack. The handles allow
the unit to be easily slid in and out of the rack, if drawer mounted. Install the
mounting ears and handles as follows:
1. Attach the mounting ears, part number 1298530501 to each side of the
unit using the 10-32 X 3/8 black pan head screws, part number
8003733401.
2. Attach the handles, part number 1298531301 to the mounting ears using
the 8-32 X 1/2 flat head screws part number 8003736101.