Vicon SVFT-C22 User manual

Vicon part number 8009-8134-01-00 Section 3 Rev 205
XX134-01-00
Camera Dome
Warning: To reduce a risk of fire or electric shock, do not expose
the indoor unit to rain or moisture.
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your
requirements or that the operation will be entirely error free or perform precisely as described in the
documentation. This system has not been designed to be used in life-critical situations and must not be
used for this purpose.
Copyright © 2005 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: 44/(0) 1489-566300 WEB: www.vicon-cctv.com

Important
Safeguards
12. Power Cord Protection - Power supply cords should not
be routed in trafficked areas or in tight spaces where they will
be pinched or used to bear weight. Allow some slack in the
cord where it enters the unit.
13. Outdoor Cable Grounding - Use only grounded outdoor
cables to protect against voltage surges and static charges.
Section 810 of the National Electrical Code, ANSI/NFPA 70-
1984, provides information on proper grounding of the lead-in
wire to an antenna discharge unit, size of grounding conductors
and the requirements of grounding electrodes.
GRAPHIC SYMBOL EXPLANATION
The lightening bolt symbol alerts the user to the presence of
dangerous voltage that may present the risk of electric shock.
14. Lightning - Disconnect the product from its power source
and cable system when possible to prevent damage due to
lightning and power-line surges.
15. Power Lines - Do not locate outside cables over power or
utility lines where they can fall and make direct contact. Contact
with power lines can be fatal.
16. Overloading - Do not overload wall outlets and extension
cords to prevent risk of fire and electric shock.
17. Object and Liquid Entry - Never probe through, or spill
liquid into, enclosure openings to prevent risk of fire or electric
shock.
The exclamation point symbol alerts the user to the presence of
important operating and maintenance instructions.
18. Servicing - Refer all servicing to qualified service
personnel.
1. Read Instructions - Read all safety and operating
instructions before the product is operated. 19. Damage Requiring Service - Obtain service when:
2. Retain Instructions - Retain all safety and operating
instructions for future reference. a) The power-supply cord or plug is damaged.
b) Objects have fallen or liquid has been spilled into the
product.
3. Heed Warnings - Pay attention to all product warnings.
4. Follow Instructions - Follow all operating instructions. c) The product is not designed for outdoor use and has been
exposed to water or moisture.
5. Cleaning -(Do not use caustic, abrasive or aerosol
cleaners) d) The product does not operate per the operating
instructions. Perform Vicon recommended adjustments,
modifications and troubleshooting only to avoid unit
damage and personal injury.
a) For units that CAN BE DISCONNECTED from the power
source, use a damp cloth for cleaning.
b) For units that CANNOT BE DISCONNECTED from the
power source, use a damp cloth for cleaning and do not
allow moisture or liquids to enter vents.
e) The product has been dropped.
f) The product shows a significant change in performance.
6. Attachments - Use only Vicon recommended attachments
to prevent unit damage and personal injury.
20. Replacement Parts - Use only Vicon specified
replacement parts or an approved equivalent to prevent unit
damage and injury.
7. Water and Moisture - Use only products designed for
outdoor environments where they will be exposed to water or
moisture. 21. Safety Check - Request safety checks to be performed
following repair or maintenance to verify proper operation.
8. Accessories - Do not place the unit on an unstable surface
to avoid falling. Use only Vicon recommended mounting accessories.. 22. ESD Precaution - Take all normal electrostatic discharge
precautions to avoid component damage during installation and
operation.
9. Ventilation - Do not block ventilating slots and openings as
they ensure reliable operation. Do not place the unit near a
heat source or into an enclosure unless recommended by
Vicon. 23. For 230 VAC Devices- When the disconnect device is not
incorporated in the equipment or when the plug on the power
supply is intended to serve as the disconnect device, follow the
guidelines below:
10. Power Sources - The product should only be operated
from the recommended power source. If not specified, consult
your Vicon dealer or local power company.
11. Grounding - Only products equipped with a 3-prong
grounded plug should be inserted into a grounded power outlet.
Contact an electrician to replace an obsolete outlet. Do not
force a plug into a non-grounded outlet.
a) For permanently connected 230 VAC units, a readily
accessible disconnect device must be incorporated into
the site wiring.
b) For 230 VAC units with a plug, the outlet must be installed
near the unit and be easily accessible.

FCC Notice
Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a
Class A digital device.
WARNING
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in
strict accordance with the manufacturer’s instruction, may cause interference to radio and television
reception. It has been type tested and found to comply with the limits for a Class A computing device in
accordance with the specification in subpart B of part 15 of the FCC rules, which are designed to provide
reasonable protection against such interference in a commercial installation. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause interference to radio
and television reception, which can be determined by turning equipment off and on, the user is encouraged to
try and correct the interference by one or more of the following measures:
•Reorient the receiving antenna.
•Relocate the equipment with respect to the receiver.
•Relocate the equipment away from the receiver.
•Plug the equipment into a different electrical outlet so that the equipment and receiver
are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional
suggestions.
The user may find the following booklet prepared by the Federal Communications Commission helpful:
“Interference Handbook, Bulletin CIB-2”
This booklet is available from the U.S. Government Printing Office, Superintendent of Documents, Mailstop
SSOP, Washington, D.C. 20402-9328, ISBN 0-16-045542-1.
Warning: Power must be removed from this unit before removing circuit modules or ribbon cables.
Caution: This unit contains circuit cards with integrated circuit devices that can be damaged by static
discharge. Take all necessary precautions to prevent static discharge
ii •FCC Notice XX134-01-00 Rev 205 SurveyorVFT Camera Dome System

Contents
INTRODUCTION...................................................................................................................1
How to Use this Manual.................................................................................................................................3
Accessory Kits................................................................................................................................................4
Unpacking and Inspection.............................................................................................................................4
SurveyorVFT Components ............................................................................................................................7
Enclosure ..................................................................................................................................................7
Camera Drive ............................................................................................................................................7
Shroud.......................................................................................................................................................7
Lower Dome ..............................................................................................................................................7
Housing .....................................................................................................................................................7
Sunshield...................................................................................................................................................7
INSTALLATION....................................................................................................................9
Quick Installation – In-Ceiling Model..........................................................................................................10
Quick Installation – Indoor Pendant ..........................................................................................................11
Quick Installation – Outdoor Pendant........................................................................................................12
Detailed Installation .....................................................................................................................................13
In-Ceiling Mount Model...............................................................................................................................13
Use of the Provided Scribe .....................................................................................................................13
Indoor Pendant Model ................................................................................................................................18
Outdoor Pendant Model..............................................................................................................................21
WIRING...............................................................................................................................26
Typical Relay and Alarm Connections .......................................................................................................28
Installing the Cables ....................................................................................................................................29
For an In-Ceiling Installation ...................................................................................................................29
For an Indoor or Outdoor Pendant Model Installation.............................................................................30
Installation Configurations..........................................................................................................................34
Installing the Flash Upgrade and PC Direct Control ................................................................................35
Standalone Configuration ...........................................................................................................................35
Star Configuration.......................................................................................................................................36
CONFIGURATION..............................................................................................................38
Setting the DIP Switches .............................................................................................................................38
XX134-01-00 Rev 205 SurveyorVFT Camera Dome System •iii

For RS-422/485 Mode: ........................................................................................................................... 38
For Vicoax Mode:.................................................................................................................................... 38
Setting the End-of-Line Jumpers JP1, JP2 & JP3 for RS-485 Protocol Operation ................................ 41
Configuring the ViconNet (IP/LAN) Version ............................................................................................... 41
Configuring the Network Settings ........................................................................................................... 42
Using the VNSetup.............................................................................................................................. 42
Upgrading Software Version................................................................................................................... 43
ViconNet Configuration........................................................................................................................... 44
UNINSTALLING THE SURVEYORVFT ............................................................................. 46
For an In-Ceiling Installation................................................................................................................... 46
For a Pendant Installation....................................................................................................................... 46
OPERATION ...................................................................................................................... 47
Initial Power-Up ...................................................................................................................................... 47
Verifying Proper Operation ......................................................................................................................... 48
Testing Preset 93 ....................................................................................................................................... 48
Use of the Auto-Baud Detect Feature........................................................................................................ 48
Troubleshooting........................................................................................................................................... 49
ViconNet (IP/LAN) Version Operation........................................................................................................ 45
COMPETITIVE PROTOCOLS............................................................................................ 50
Testing Conditions .................................................................................................................................. 50
MAINTENANCE ................................................................................................................. 58
Care and Cleaning of Metallized Domes.................................................................................................... 58
Care and Cleaning of Smoked and Clear Acrylic Domes ........................................................................ 58
Fuse Replacement ....................................................................................................................................... 58
SHIPPING INSTRUCTIONS............................................................................................... 59
REFERENCE ..................................................................................................................... 60
Coaxial Cable Recommendations .............................................................................................................. 60
Twisted-Pair Cable....................................................................................................................................... 61
1.5-inch Pipe Designation ........................................................................................................................... 61
TECHNICAL INFORMATION............................................................................................. 63
Camera Specifications........................................................................................................................... 66
VICON STANDARD EQUIPMENT WARRANTY ............................................................... 68
iv •Contents XX134-01-00 Rev 205 SurveyorVFT Camera Dome System

Introduction
The information in this manual covers the installation, configuration and operation of the SurveyorVFT
Camera Dome. This system should only be installed by a qualified technician using common hand tools and
approved materials and wiring methods in accordance with the national Electric Code ANSI/NFPA 70, state
and local wiring codes.
NOTE: Read all instructions before beginning any installation.
The SurveyorVFT is a compact, lightweight intelligent security device comprised of a camera, pan/tilt drive,
receiver and CPU-based electronics all in an attractive and covert enclosure. SurveyorVFT can be
programmed and operated using any V1300X/V1400X/1500 series of NOVA communication devices and
enhanced Vicoax II protocol. SurveyorVFT is sold in a variety of prepackaged configurations with choices in
environment, mounting configuration, camera type, and lower dome types. Refer to Table 1 for a complete list
of model numbers. Refer to product specification V134-0X and V134-2X (ViconNet version) for a list of
optional equipment, including power supplies, mounts, lower domes and receivers.
The basic SurveyorVFT provides video transmission over coaxial cable. Options are available that provide
TCP/IP (ViconNet), fiber-optic and twisted-pair (UTP/NVT) video transmission. Each of these options includes
an interface board that allows the specific type of video transmission. An appropriate receiver is required for
UTP/NVT and fiber optic versions. The ViconNet option provides support for direct network connection to
Kollector Elite Digital Video Recorders and ViconNet Workstations via ViconNet software. A pre-installed LAN
interface board allows direct plug-in to a system network hub, switch or router. Video from the camera is
available to all network recorders and workstations for live view and recording. The Vicon SurveyorVFT
camera dome can be used in conjunction with competitive PTZ drivers through DIP switch selection.
The SurveyorVFT is designed for easy snap-in installation. The drive simply snaps into the housing. When
removed, the housing retains all programmed functions in its on-board memory. The customer interface
board snaps down for easy access and the PCB provides removable terminal blocks for simple wiring
connections. Several mounting accessories are available to fit almost any installation need.
There are three camera types available, each with NTSC and PAL versions. The basic model is a 22X high-
resolution camera/lens. Another 22X model is available with ExVIew CCD technology (22XEX). The third
version is a 23X day/night camera/lens. See Technical Information for camera features.
Refer to tables below for specific model numbers and options available. Call your Vicon representative for
model availability. All versions use the same firmware for programming and operation. For programming,
refer to the SurveyorVFT Programming Manual XX134-4X.
SurveyorVFT meets requirements for an FCC Class A computing device. SurveyorVFT complies with the fire
code of certain local municipalities. The fire code for any given municipality should be verified for
SurveyorVFT’s compliance at the installation site.
Vicon strongly recommends the use of line conditioners, voltage regulators and uninterruptible power supply
(UPS) systems in the electrical power service. The electronic components within the SurveyorVFT are
sensitive to damage from ESD (Electro-Static Discharge). Appropriate precautions and proper use of a
ground strap should be observed at all times when handling the unit or its subassemblies.
XX134-01-00 Rev 205 SurveyorVFT Camera Dome System Introduction •1

SurveyorVFT Models
Model Number Product
Code
Environment/
Cable Type
Camera
Type/Format
Mount
Type
Optical Zoom/
Total Zoom
Lower
Dome Type
SVFT-C22 8701-00 Indoor/Coax Color/NTSC Ceiling ExView 22x/264x Smoked
SVFT-C22C 8701-01 Indoor/Coax Color/PAL Ceiling ExView 22x/264x Smoked
SVFT-P22 8704-00 Indoor/Coax Color/NTSC Pendant ExView 22x/264x Smoked
SVFT-P22C 8704-01 Indoor/Coax Color/PAL Pendant ExView 22x/264x Smoked
SVFT-W22 8707-00 Outdoor/Coax Color/NTSC Pendant ExView 22x/264x Clear
SVFT-W22C 8707-01 Outdoor/Coax Color/PAL Pendant ExView 22x/264x Clear
SVFT-C23 8702-00 Indoor/Coax Color/NTSC
(day/night)
Ceiling 23x/276x Clear
SVFT-C23C 8702-01 Indoor/Coax Color/PAL
(day/night)
Ceiling 23x/276x Clear
SVFT-P23 8705-00 Indoor/Coax Color/NTSC
(day/night)
Pendant 23x/276x Clear
SVFT-P23C 8705-01 Indoor/Coax Color/PAL
(day/night)
Pendant 23x/276x Clear
SVFT-W23 8708-00 Outdoor/Coax Color/NTSC
(day/night)
Pendant 23x/276x Clear
SVFT-W23C 8708-01 Outdoor/Coax Color/PAL
(day/night)
Pendant 23x/276x Clear
SVFT-C22CA 8741-00 Indoor/Coax Color/NTSC Ceiling 22x/264x Smoked
SVFT-C22CA-C 8741-01 Indoor/Coax Color/PAL Ceiling 22x/264x Smoked
SVFT-P22CA 8742-00 Indoor/Coax Color/NTSC Pendant 22x/264x Smoked
SVFT-P22CA-C 8742-01 Indoor/Coax Color/PAL Pendant 22x/264x Smoked
SVFT-W22CA 8743-00 Outdoor/Coax Color/NTSC Pendant 22x/264x Clear
SVFT-W22CA-C 8743-01 Outdoor/Coax Color/PAL Pendant 22x/264x Clear
For the ViconNet (V) option, add -20 to the product code; for Fiber Optic (F) option, add -30 to the product code;
for the Twisted Pair (T) option, add -40 to the product code.
Table 1
Models and Descriptions
2 •Introduction XX134-01-00 Rev 205 SurveyorVFT Camera Dome System

How to Use this Manual
This manual was designed to provide the best overall instructions for the installation and operation of the
SurveyorVFT Camera Dome. The graphics and terminology used in this manual have been carefully selected
to enable a clear and distinct understanding of the SurveyorVFT and its components. This manual has been
formatted to present distinct methods of installation for all installers.
For a quick overview of product installation, see the Quick Installation sub-section of the Installation section
and choose the appropriate method (In-Ceiling Mount Model, Indoor Pendant Model or Outdoor Pendant
Model) to begin. Follow the references provided in the text for items such as wiring tables, DIP switch settings
and lower dome care. Refer to the subsequent sections of Installation, Wiring, Configuration and Operation
for detailed descriptions of any method.
The Operation section of this manual was written using the available features in the latest revision of the
SurveyorVFT software. The actual version of software may vary in any particular camera dome and support
different features than actually described here.
XX134-01-00 Rev 205 SurveyorVFT Camera Dome System Introduction •3

Accessory Kits
There are 3 different accessory kits included with the different configurations of SurveyorVFT;
Standard/Fiber-Optic Option, Twisted Pair (UTP/NVT) Option and ViconNet (LAN/TCP/IP) Option. These kits
provide the necessary items for installation as follows:
Standard/Fiber-Optic Versions
Description Quantity
8-position terminal block (1302-3313-02) 2
2-position terminal block (8004-8084-02) 1
Twisted Pair Version
Description Quantity
8-position terminal block (1302-3313-02) 2
2-position terminal block (8004-8084-02) 1
3-position terminal block (1302-3313-01) 1
ViconNet Version
Description Quantity
8-position terminal block (1302-3313-02) 1
2-position terminal block (8004-8084-02) 1
3-position terminal block (1302-3313-01) 1
NOTE: A packet of anti-seize lubricant is included in the outdoor housing accessory kit only. A scribe and a
strain relief are included in the in-ceiling unit accessory kit only.
Refer to the Wiring section of this manual for details on using the supplied removable termination blocks. The
scribe is supplied to accurately measure the opening for the in-ceiling model. The lubricant is used for sealing
and to prevent galling at the end of the 1.5-inch NPT pipe on the outdoor pendant model. Refer to the outdoor
pendant model sub-section of the Installation section for details on applying the lubricant.
Unpacking and Inspection
All Vicon equipment is tested and inspected before leaving the factory. It is the carrier’s responsibility to
provide suitable delivery.
Inspect the cartons upon delivery and, if damage is present, make detailed notes on the carrier’s bill. Then,
obtain the carrier agent’s signature and file a damage claim as soon as possible.
Open the cartons and inspect the equipment for damage. Save the cartons and packing material. If damage
is present, contact the carrier and file a damage claim immediately. If the equipment must be returned for
repair, follow the instructions in the Shipping Information section of this manual.
4 •Introduction XX134-01-00 Rev 205 SurveyorVFT Camera Dome System

Unpacking the SurveyorVFT In-Ceiling
Unpacking the SurveyorVFT Indoor Pendant
XX134-01-00 Rev 205 SurveyorVFT Camera Dome System Introduction •5

Unpacking the SurveyorVFT Outdoor Pendant
6 •Introduction XX134-01-00 Rev 205 SurveyorVFT Camera Dome System

SurveyorVFT Components
All SurveyorVFT units are comprised of an Enclosure/Housing, a Camera
Drive, a Shroud and a Lower Dome. Figures 1, 2 and 3 show In-Ceiling,
Indoor Pendant and Outdoor Pendant models, respectively.
Figure 1
SurveyorVFT In-Ceiling
Enclosure
The enclosure is a metal shell that houses the camera drive for the in-
ceiling model. A safety cord and clip are provided to connect to the camera
drive during installation. In addition, a small hole is provided on the side of
the enclosure for connection of the lower dome’s safety cord. A removable
top cover, a 0.75-inch (19 mm) conduit fitting and a pair of rotating flippers
that give a convenient and sturdy connection of the enclosure into the
ceiling are provided. For in-ceiling installations that do not use conduit pipe,
a 0.75-inch (19 mm) strain relief fitting provides solid cable anchoring at the
enclosure. A customer interface board, that can be unlatched or removed
for easy access, is installed in the top of the enclosure. All wiring is done to
this board.
Camera Drive
The camera drive is comprised of an integral camera, pan-and-tilt drive and
CPU. It is designed for easy “snap-in” installation into the enclosure or
housing. The camera drive quickly and accurately positions the camera in
360°of pan angle and 95°of tilt angle. There are variations in camera type
for magnification and color or day/night usage. An additional
thermostatically-controlled heater is provided for temperature control on
outdoor units.
Shroud
The shroud is a 5.4 in. (137 mm) textured black ABS plastic shell. It has a
1.4 in. (35.6 mm) slotted opening for the camera. This shroud conceals the
position of the camera and snaps onto the camera drive.
Lower Dome
The lower dome is an assembly comprised of a 5.98 inch (152 mm)
diameter acrylic plastic shell, a trim ring and a safety cord. Lower domes
for indoor versions come in a choice of smoked, chrome or gold finishes.
Standard outdoor lower domes are clear and use 4 screws for additional
support. All lower domes are anchored to the enclosure by the safety cord.
Refer to the Maintenance section for care.
Housing
The housing for the SurveyorVFT indoor pendant configurations is a
molded plastic protective cover for the camera drive; outdoor pendant
configurations have a die-cast aluminum housing with a sunshield. The
housing has a 1.5-inch NPT pipe flange mount. In addition, the housing is
equipped with a safety cord and clip that is used to suspend the camera
drive during installation. Another safety cord connects the lower dome to
the housing. A customer interface board, that can be unlatched or removed
for easy access, is installed in the top of the enclosure. All wiring is done to
this board.
Sunshield
The sunshield is pre-installed over the housing used on the outdoor
pendant version to minimize the effects of solar radiation.
CAUTION: For any environment subject to moisture, use the outdoor
pendant model.
XX134-01-00 Rev 205 SurveyorVFT Camera Dome System Introduction •7

Figure 3
SurveyorVFT Outdoor Pendant
Figure 2
SurveyorVFT Indoor Pendant
8 •Introduction XX134-01-00 Rev 205 SurveyorVFT Camera Dome System

XX134-01-00 Rev 205 SurveyorVFT Camera Dome System Introduction •9

Installation
Choose the installation type based on the specific unit purchased (In-Ceiling, Indoor or Outdoor Pendant).
Quick Installation – In-Ceiling Model
Q
U
I
C
K
I
N
S
T
A
L
L
A
T
I
O
N
Q
U
I
C
K
I
N
S
T
A
L
L
A
T
I
O
N
10 •Installation XX134-01-00 Rev 205 SurveyorVFT Camera Dome System

Quick Installation – Indoor Pendant
Q
U
I
C
K
I
N
S
T
A
L
L
A
T
I
O
N
Q
U
I
C
K
I
N
S
T
A
L
L
A
T
I
O
N
XX134-01-00 Rev 205 SurveyorVFT Camera Dome System Installation •11

Quick Installation – Outdoor Pendant Q
U
I
C
K
I
N
S
T
A
L
L
A
T
I
O
N
Q
U
I
C
K
I
N
S
T
A
L
L
A
T
I
O
N
12 •Installation XX134-01-00 Rev 205 SurveyorVFT Camera Dome System