Victorian Plumbing VIS023 User manual

INSTALLATION INSTRUCTIONS FOR
IP44 ILLUMINATED MIRRORS
Before installing this product pay special attention to these instructions. It is recommended that this
product is installed by a qualified electrician to IEE wiring regulations (BS 7671) and current building
regulations. These products can safely be fitted into Zone 2. See lighting regulations diagram.
Installation steps
1. Prior to commencing work isolate the power supply cable at the main fuse box.
2. Check that there are no other concealed cables or pipe work in the intended installation area
(check the entire area).
3. The mirror is mounted on the wall by means of two fixing screws.
4. Make sure that it is at the correct height and level. Using a suitable marker through the fixing
holes mark the position of the holes on the wall.
5. Using the correct size drill bit for the wall fixing drill holes in the marked locations. (Please note
that for certain wall types i.e. plasterboard walls, the wall fixings supplied are not
recommended)
6. Place the rawl plugs into the holes. Feed the supply through the central rubber grommet,
position the back plate and secure using the correct fixings (the rubber washers provided must
be used to ensure no water can penetrate into the fitting).
7. Connect the supply cable to the connector block as shown in the wiring diagram. Ensure the
conductors are fully inserted into the terminals and no loose wire strands are protruding. Fully
tighten the screws on the terminals making sure that the screw clamps onto the conductor and
not the insulation.
8. Fix the mirror to the wall.
9. Ensure that the correct type and wattage bulb are always used. (see Luminaire for details).
10. Finally switch on the power, and then touch the switch sign with a finger on the sensor or wave
hands below sensor to test the product.
Shelf fixing (selected models only).
To fix glass shelf to mirror attach the metal support arms to the bottom of the mirror frame using
the screws provided. The rubber washer supplied must be used to ensure that IP44 is maintained.
Place the glass shelf and secure with the screws located underneath the metal support arm. Care
must be taken not to over tighten.
Cleaning Instructions
In order to maintain the quality finish of this product please do not use any abrasives or solvents
when cleaning this product. Use only a damp cloth for cleaning this product. Do not allow water to
stand on any part of the mirror.
Please clean any spillage that may affect the quality of the finish as described above.
Special care
Care Should be exercised when cleaning this product. Although its finish is extremely durable, it can
be damaged by harsh abrasives and cleaning pads. To clean, use a light, non-abrasive cleaning
solution or cleaning polish.
V1.10.2022

Packing information & installation
Package content:
• LED Backlit Mirror
• Manual
• Fixings
Attention: Installation and connection to electric wiring must be done by a
professional electrician in compliance with local and national requirements for
electrical installations.
Never modify the construction or add any parts which are not offered as spare
parts or accessories by the manufacturer of the luminaire. Any unauthorized
modification might result in weak mounting and risk that parts of the luminaire
can fall down from the wall.
Warning: Always switch off the Electrical supply at the mains during
installation and maintenance.
Warning: This product must be earthed
Note: Install the mirror at least 15cm. away from the basin.
V1.10.2022

Electrical Wiring
Brown/Red/Black
Yellow/Green/Green
Blue/Black/White
Brown
Yellow/Green
Blue
Mirror Main Supply
V1.10.2022

Functions
Heated Demister Pad
Demister pads heat the surface of the mirror above room temperature
removing the mist on the surface .If your mirror comes
with a demister then it will turn off/on using main power button/sensor. It
takes 3-4 minutes for complete heat up and fog removal. For some special
models there might be a special button to control demister.
IR Sensor
The IR sensor switch can be used to to perform multiple functions: Wave
hands in front of sensor to change led color or turn lights on/off. When the
lights are on, placing hands in front of sensor can change brightness of
light.
Touch Sensor
The touch sensor switch can be used to Turn Led Lights .You can tap the
touch sensor for On/Off .If your mirror comes with color changing strips
then you can long press the touch sensor to change colour from
warm(3000k) to white(6000k).
Shaver Socket
You can plug your shaver/electric toothbrush to the socket on side of
mirror.
Bluetooth
If your comes with an inbuilt bluetooth. You can scan and
connect bluetooth on mirror with your phone to play music.
V1.10.2022

Hanging the mirror
Installation Procedure
To ensure the normal use of this product, it is required you set out wires as per the regulations of IEE
at the installation places. This product should be installed on a wall suitable to hold its weight. The
installation must be carried out by a professional electrician and wrong installation may lead to
product damage and personal injury.
Installation Tools
Measuring tape Spirit Level Drill Hammer Screwdriver Pencil
Types of hanging brackets
V1.10.2022

Hanging the mirror
Installation Steps
1. Make certain the wall is solid and suitable to safely accommodate the mirrors overall weight when
installed. Measure and mark with a pencil, the position of the fixing bracket, securing screws &
plugs while checking with a spirit level that the bracket is perfectly level.
2. Choose a drill with an appropriate drill bit to make two (or more) holes at the marked places, and
use a special ceramic drill if the wall surface is made of ceramic tiles.
3. Insert Rawl plugs into drilled holes, and then screw the hook into the hole .
4. Switch off the power, and then use a terminal block to connect the three-core exposed wires with
your incoming mains cable feed.
5. Hang the product on the wall hook.
6. Finally switch on the power, and then touch the switch sign with a finger on the sensor or wave
hands below sensor to test the product.
Recycling and disposal
Please recycle the packaging in accordance with your local government regulations on
waste handling, and follow the same advice at the end of the products life.
For more Information visit: victorianplumbing.co.uk
V1.10.2022