Victory E3 Assembly instructions

Installation Guide
and Users Manual
Under Cabinet Range Hood
NOTICE:
Installer: Leave this guide with the homeowner
Homeowner: Keep this guide for future reference
IMPORTANT:
Read and save these instructions.
Rev. 1027u.1a
VICTORY
Professional Range Hood
Model number: E3
available sizes: 30”, 36”

Important Safety Notice
Read all Instructions before Installing and operating this appliance
• Theinstallationinthismanualisintendedforqualiedinstallers,servicetechniciansorpersonswith
similarqualiedbackground.Installationandelectricalwiringmustbedonebyqualiedprofession-
alsandinaccordancewithallapplicablecodesandstandards,includingre-ratedconstruction.
• DO NOTattempttoinstallthisapplianceyourself.Injurycouldresultfrominstallingtheunitdueto
lackofappropriateelectricalandtechnicalbackground.
• Rangehoodmayhaveverysharpedges;pleasewearprotectiveglovesifitisnecessarytoremoveany
parts for installing, cleaning or servicing.
• ActivatinganyswitchONbeforecompletinginstallationmaycauseignitionoranexplosion.
• Due to the size and weight of this range hood, two people installation is recommended.
To reduce the risk of re, electric shock, or injury to persons:
• Forgeneralventilatinguseonly.DO NOTusetoexhausthazardousorexplosivematerialsandva-
pors.
• Thecombustionairowneededforsafeoperationoffuel-burningequipmentmaybeaffectedbythis
unit’soperation.Followtheheatingequipmentmanufacturer’sguidelineandsafetystandardssuch
asthosepublishedbytheNationalFireProtectionAssociation(NFPA),andtheAmericanSocietyof
Heating,RefrigerationandAirConditioningEngineers(ASHRAE),andthelocalcodeauthorities.
• Beforeservicingorcleaningunit,switchpowerOFFatservicepanelandlockservicepaneltopre-
ventpowerfrombeingswitchedONaccidentally.
• Cleangreaseladensurfacesfrequently.Toreducetheriskofreandtodisperseairproperly,make
sure to vent air outside. DO NOTventexhaustintospacesbetweenwalls,crawlspaces,ceiling,attics
or garages.
• DuctedfansMUSTalwaysbeventedtotheoutdoors.
• UseonlymetalductworkandthisunitMUSTbegrounded.
• Sufcientairisneededforpropercombustionandexhaustingofgasesthroughtheducttoprevent
backdrafting.
• When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hid-
den utilities.
• Allelectricalwiringmustbeproperlyinstalled,insulatedandgrounded.
• Oldductworkshouldbecleanedorreplacedifnecessarytoavoidthepossibilityofagreasere.
• Checkalljointsonductworktoinsureproperconnectionandalljointsshouldbeproperlytaped.
• Usethisunitonlyinthemannerintendedbythemanufacturer.Ifyouhavequestions,contactthe
vendor.
To reduce the risk of a stove top grease re:
• Keepallfan,bafe,spaces,lter,greasetunnel,oilcontainerandgrease-ladensurfacesclean.Grease
shouldnotbeallowedtoaccumulateonfan,bafe,spaces,lter,greasetunnelandoilcontainer.
• AlwaysturnrangehoodONwhencookingathighheatorwhencookingamingfoods.
• Usehighsettingsoncookingrangeonlywhennecessary.
• Neverleavesurfaceunitsunattendedathighsettings.Boiloverscausesmokingandgreasyspillovers
thatmayignite.Heatoilsslowlyonlowormediumsettings. Page1

Page2
Important Safety Notice
Read all Instructions before Installing and operating this appliance
WARNING
Yoursafetyandthesafetyofothersisveryimportant.Wehaveprovidedmanyimportantsafetymes-
sagesinthismanualandonyourappliance.Alwaysreadandobeyallsafetymessages.Allsafetymes-
sageswilltellyouwhatthepotentialhazardis,tellyouhowtoreducethechanceofinjury,andtellyou
what can happen if the instructions are not followed.
Thisisthesafetyalertsymbol.Thissymbolalertsyoutopotentialhazardsthatcanhurtyouandothers.
Allsafetymessageswillfollowthesafetyalertsymbolandtheword“WARNING”.
The manufacturer and/or distributor/reseller declines all responsibility in the event of failure to ob-
serve the instructions given here for installation, maintenance and suitable use of the product.
The manufacturer and/or distributor/reseller further declines all responsibility for injury due to neg-
ligence and the warranty of the unit automatically expires due to improper maintenance.
The manufacturer and/or distributor/reseller will not be held responsible for any damages to per-
sonal property or real estate or any bodily injuries whether caused directly or indirectly by the range
hood.
• Cleanventilatingfanfrequently.
• Alwaysuseappropriatecookwareandutensilssize.
• Alwaysusecookwareappropriateforthesizeofthesurfaceelement.
To reduce the risk of injury to persons in the event of a stove top grease re:
• SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnOFFtheburner.
BECAREFULTOPREVENTBURNS.NEVERPICKUPAFLAMINGPAN—youmaybeburned.
KEEPFLAMMABLEORCOMBUSTIBLEMATERIALAWAYFROMFLAMES.IftheamesDO
NOTgooutimmediately,EVACUATEANDCALLTHEFIREDEPARTMENTordialyourlocal
emergencyserviceimmediately.
• DONOTUSEWATER,includingwetdishclothsortowels—aviolentsteamexplosionwillresult.
• UseanextinguisherONLYif:
• YouknowyouhaveaClassA,B,Cextinguisher,andyoualreadyknowhowtooperateit.
• Thereissmallandcontainedintheareawhereitisstarted.
• Theredepartmentisbeingcalled.
• Youcanghttherewithyourbacktoanexit.
To reduce the risk of injury to persons in the event of a gas leaks:
• Extinguishanyopename.
• DONOTturnontherangehoodfanoranytypeofventilator.
• DONOTturnonthelightsoranytypeofappliance.
• Openalldoorsandwindowstodispersethegas.Ifyoustillsmellgas,callthegascompanyandre
department,ordialyourlocalemergencyserviceimmediately.

Table of Contents
INSTALLATION
Tools needed....................................................3
Partssupplied...................................................4
Ventingrequirements.......................................5
Mountheights&clearance...........................5-6
Calculatingventsystemlength.......................6
Ventingmethods..............................................7
Electrical requirements....................................8
Preparation......................................................9
Installation................................................10-11
Rangehoodoperations..................................12
USE AND CARE
Troubleshooting...........................................13
Useandcareinformation...............................14
Specications..............................................14
Measurements&Diagrams......................15-16
MAINTENANCE
Cleaning.................................................17
Replacingthelter&lightbulb.....................17
WARRANTY
Coverage&exceptions..................................18
Disclaimer&ContactUs...............................19
Tools needed:
Page3
Level
Flat-blade
andPhillips
screwdrivers
Powered
screwdriver
or drill
Measuring
tape
Utilityknife
Markeror
pencil

Page4
Parts supplied:
Qty:4PCS
(Forsheetrockonly)
Qty:4PCS
Qty:6PCS
Under Cabinet Range Hood
Flappers
StainlessSteelBafeor
AluminumFilter(s)
RoundExhaust

Ceiling
Height
Venting Requirements
Page5
Height & Clearance
Under Cabinet
Range hood
36”
Counter
Top
Min:
27”
Max:30”
• Vent system must terminate to the outside
(rooforsidewall).
• DONOTterminatetheventsysteminanat-
tic or other enclosed area.
• DONOTuse4”(10.2cm)laundry-typewall
caps.
• Usemetal/aluminumventonly.Rigidmetal/
aluminum vent is recommended.
• DO NOT use plastic vent.
• Alwayskeeptheductcleantoensureproper
airow.
• Calculatethefollowingguresbeforeinstal-
lation:
1. Distance from the oor to the ceiling.
2. Distance between the oor to the coun-
tertop/stove (recommend* 27” to 30”).
3. Distance between the countertop/stove
to the range hood.
4. Height of hood and duct cover.
For the most efcient & quiet operation:
• Adistance of 27”to30” is recommended*
between stove top and the bottom of range
hood.
• It is recommended that the range hood be
ventedverticallythroughtheroofthrough8”
(20.3cm) or bigger roundmetal/aluminum
ventwork.
• The size of the vent should be uniform.
• Usenomorethanthree90°elbows.
• Make sure there is a minimum of 24” (61
cm) of straight vent between the elbows if
more than one elbow is used.
• DO NOT install two elbows together.
• The length of vent system and number of
elbowsshouldbekepttoaminimumtopro-
videefcientperformance.
• The vent system must have a damper. If
roof or wall cap has a damper, DO NOT
usedamper(ifsupplied)ontopoftherange
hood.
• Usesilvertapeorducttapetosealalljoints
intheventsystem.
• Use caulking to seal exterior wall or roof
opening around the cap.
*Duetodifferentceilingheightcongurations,rec-
ommendedheightmaynotbeapplicable.
Cabinet
Range
Hood
Height
Cabinet
Height
Countertop/Stove

Page6
Duct Run Calculation:
Recommendedmaximumrun
8”or3-1/4x10”duct 50ft
Ventpiecededuction
Each90ºelbowused 9ft
Each45ºelbowused 5ft
Each7”to3/14x10”transitionused 7ft
Sidewallcapwithdamper 0 ft
Roof cap 0 ft
Duct Run Calcuation example:
One roof cap, two 90º elbow, and one 45º elbow used:
0ft + 9ft + 9ft + 5ft = 23ft used.
Deduct 23ft from 50ft, 27ft maximum available for
straight duct run.
Calculating Vent System Length
Tocalculatethelengthofthesystemyouneed,deducttheequivalentfeetforeachventpieceusedinthesystem
fromtherecommendedmaximumductrun.
IMPORTANT:
• Aminimumof6”round(standardforthisrangehood)or3-1/4x10”rectangularduct(purchasedseparately)
mustbeusedtomaintainmaximumairowefciency.
• Flexible6”roundductprovidedforconvenience,alwaysuserigidtypemetal/aluminumductsifavailableto
maximizeairowwhenconnectingtoprovidedduct.
• PleaseuseDuct Run Calculation below to compute the total available duct run when using elbows, transitions
and caps.
• ALWAYS,whenpossible,reducethenumberortransitionsandturns.Iflongductrunisrequired,increaseduct
sizefrom6”to7”or8”.Ifareducerisused,installalongreducerinsteadofapancakereducer.Reducingduct
sizewillrestrictairowanddecreaseairow,thusreduceductsizeasfarawayfromopeningaspossible.
• Ifturnsortransitionsarerequired:Installasfarawayfromopeningandasfarapart,between2,aspossible.
• Minimummountheightbetweenstovetoptohoodbottomshouldbenolessthan28-inch*.
• Maximummountheightbetweenstovetoptohoodbottomshouldbenohigherthan31-inch*.
• Itisimportanttoinstallthehoodatthepropermountingheight.Hoodsmountedtoolowcouldresultinheat
damageandrehazard;whilehoodsmountedtoohighwillbehardtoreachandwilllooseitsperformance
andefciency.
• Ifavailable, alsorefer to stovetop manufacturer’sheight clearancerequirements andrecommended hood
mounting height above range.
*Duetodifferentceilingheightcongurations,recommendedheightmaynotbeapplicable.
Minimum Duct Size:
• Round - 6” minimum
• Rectangular-3-1/4x10”minimum(requiresa6”to3-1/4x10”adaptor,notsupplied)

Venting Methods
Page7
• Thisrangehoodisfactorysetforventingthroughtherooforwall.
• Ventworkcanterminateeitherthroughtherooforwall.Toventthroughawall,a90°elbowisneeded.
IMPORTANT:
• NEVERexhaustairorterminateductworkintospacesbetweenwalls,crawlspaces,ceiling,atticsor
garages.Allexhaustmustbeductedtotheoutside.
• Usemetal/aluminumductworkonly.
• FastenallconnectionswithsheetmetalscrewsandtapealljointswithcertiedSilverTapeorDuctTape.
• Usecaulkingtosealexteriorwallorroofopeningaroundthecap.
Vertical roof venting
Roof cap
Option 2:
Sidewallcap
Horizontal wall venting
Option 1:

IMPORTANT: Observe all governing codes and ordinances.
(Please consult with a qualied electrician for 220-Volt 50 Hz voltage)
It is the customer’s responsibility:
• Tocontactaqualiedelectricalinstaller.
• ToassurethattheelectricalinstallationisadequateandinconformancewithNationalElectricalCode,ANSI/
NFPA70—latestedition*,orCSAStandardsC22.1-94,CanadianElectricalCode,Part1andC22.2No.
0-M91-latestedition**andalllocalcodesandordinances.
Ifcodespermitandaseparategroundwireisused,itisrecommendedthataqualiedelectriciandeterminethat
the ground path is adequate.
A120-Volt,60Hz,AC-only,fusedelectricalsupplyisrequiredonaseparate15-ampcircuit,fusedonbothsides
of the line.
DO NOT ground to a gas pipe.
Checkwithaqualiedelectricianifyouarenotsurethattherangehoodisproperlygrounded.
DO NOT have a fuse in the neutral or ground circuit.
IMPORTANT:SavethisInstallationGuideforelectricalinspector’suse.
Therangehoodmustbeconnectedwithcopperwire/plugonly.
Therangehoodshouldbeconnecteddirectlytothefuseddisconnect(orcircuitbreaker)boxthroughexible
armoredornon-metallicsheathedcoppercable.AU.L.-orC.S.A.-listedstrainreliefmustbeprovidedateach
endofthepowersupplycable.
Wiresizes (copperwireonly)and connections mustconformwiththerating of theapplianceasspecied on
the model/serial rating label. Wire sizes must conform to the requirements of the National Electrical Code
ANSI/NFPA 70 — latest edition*, or CSA Standards C22. 1-94, Canadian Electrical Code Part 1 and C22.
2 No.  0-M91 - latest edition** and all local codes and ordinances.A U.L. - or C.S.A. - listed conduit con-
nector must be provided at each end of the power supply cable (at the range hood and at the junction box).
Copiesofthestandardslistedmaybeobtainedfrom:
*NationalFireProtectionAssociation
BatterymarchPark
Quincy,Massachusetts02269
** CSAInternational
8501EastPleasantValleyRoad
Cleveland,Ohio44131-5575
Page8
Electrical Requirements

Page9
Figure1 Figure2
Preparation
Advanced Preparations:
• Befamiliarwiththecontrolsoftherangehoodbyreading
through Range Hood Operations,Page12-13.
• Placetherangehoodonaat,stablesurface.Connectthe
rangehoodtoadesignatedstandardoutlet(pleasereferthe
productlabelforthesuitablevoltageofthisunit)andturnon
therangehood.Verifyall operations of the rangehoodby
referring to Range Hood Operations, Page12-13.
• Placeallsuppliedpartsandrequiredhardwareonaat,stablesurfaceandver-
ifytheexistenceofallsuppliedpartslistedonPage4.
• Carefullyremovethewhiteplasticprotectivecoatfromtherangehood.
Preparations:
NOTE: To avoid damage to your hood, prevent debris from entering the vent opening.
• Decide the location of the venting pipe from the hood to the outside. Refer to Venting MethodsonPage7.
• Astraight,shortventrunwillallowthehoodtoperformmoreefciently.
• Trytoavoidasmanytransitions,elbows,andlongrunaspossible.Thismayreducetheperformanceofthe
hood.
• IMPORTANT:Peelwhiteplasticprotectivecoatoffthehood,ifany.
• Usesilvertapeorducttapetosealjointsbetweenpipesections.
• Forinstallingunderthecabinetwithrecessedbottom,attach4-inchwidewoodllerstrips(notprovided)on
eachside.RefertoFigure1.
• Using references in Measurements and DiagramsonPage17-18,createaccessopeningforelectricalwires
andhoodexhaustunderthecabinet.
CAUTION: If moving the cooking range is necessary to install the hood, turn OFF the power on an elec-
tric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE.
• Puncturetheknockoutholes(formountingunderthecabinet)onthehoodasshowninFigure2.
• Ifnecessary,attachtworubberstandswith3Madhesivetapestothebackcornersofthehood.
WARNING
Excessive Weight
Require three or more person to move and
install this range hood. Spinal or other bodily
injuries could occur if it is not followed.
WARNING
Severe Injury
Rotating fan can cause severe
injury. Stay clear of fan when
motor is running.

Page10
Installation
Installations(refertoPage4forparts):
Measure the distance between stove top and the bottom of
rangehood.Adistanceof27”to30”isrecommended*.
*Due to different ceiling height congurations, recommended
height may not be applicable.
1. You have two ways(A:VerticalVenting,orB:HorizontalVenting)tomountthisrangehood:
1. DetermineventingmethodasshownonPage7andproceedifyouwouldliketoventvertically.
2. Using references in Height & ClearanceonPage5-6,Measurements and DiagramsonPage17-18,
Figure3 andFigure 4 onnext page,determine andclearly mark acenterline onthe bottomof the
cabinet.
3. Draw electrical wires through cabinet access opening on top of the range hood, center the hood beneath
thecabinetandushwiththefrontofthecabinet.
4. Frominsideofthehood,placehoodmountingscrewsintotheexactcenterofeachknockoutholeand
secure to cabinet bottom. Finish tightening all screws until secure. Be careful when using electrical
screwdriver,damagetotherangehoodmayoccur.
CAUTION: Make certain the range hood is secure before releasing!
2. Forsafetypurpose,pre-drilledmountingholesareprovidedthroughthebackofthehood.Foramoresecure
installation,useasmanymountingholesasneededtosecurefromtheinsideofhood.
3. Use6”roundsteelpipe(followbuildingcodesinyourarea)toconnecttheexhaustonthehoodtotheduct-
workabove.Usesilvertapeorducttapetomakealljointssecureandairtight.RefertoFigure5.
4. Connecttherangehoodtoadesignatedstandardoutletorcutofftheplugandconnectthreewires(black,
whiteand green)tohousewiresandcapwithwireconnectors.Connect accordingtocolors(i.e.blackto
black,whitetowhite,andgreentogreen).
5. Storeexcesswiresinthewiringbox.
6. InstallAluminumFilterorStainlessSteelFilter
7. TurnPowerONusingcontrolpanel(refertoRange Hood OperationsonPage12).Checkalllightsandfan
operations.
8. MakesuretoleavethisInstallationGuideforthehomeowner.
SAFETY WARNING:
Risk of electrical shock. this range hood must be properly grounded. Make sure this is done by qualied
electrician in accordance with all applicable national and local electrical codes. Before connecting wires,
switch power off at service panel and lock service panel to prevent power from being switched on acciden-
tally.

Figure 3
Page11
Installation (Continued)
Figure5
Figure4

Page12
Elec. Control Panel Layout and Buttons
Power
DecreaseValue
Light
IncreaseValue
BlowerPowerIndicator
BlowerSpeedIndicator
Power-OnElapsedDigitalTimer
Power-OffDelayDigitalTimer
Power-OffDelayTimerIndicator
LightPowerIndicator
Range Hood Operations
Thisrangehoodisdesignedtoremovesmoke,cookingvaporsandodorsfromthecooktoparea.Forbestresults,
starttherangehoodbeforecookingandallowittooperateseveralminutesafterthecookingiscompletedtoclear
allsmokeandodorsfromthekitchen.
• Button functions:
• Power:PowerON/OFFtherangehoodandactivatepower-offdelaytimer.
• DecreaseValue:Blower(motor)speeddecrease,timervaluedecrease,andentertimermode.
• IncreaseValue:Blower(motor)speedincreasetimervalueincrease,andcumulativetimerreset.
• BlowerPowerIndicator:Lightsupwhenblower(motor)isrunning.
• BlowerSpeedIndicator:Showscurrentblower(motor)speed(1-6).
• LightPowerIndicator:Lightsupwhenlightsturnedon.
• Light: Turns ON/OFF and dim halogen lights.
• Power-OnElapsedDigitalTimer:Indicatestheaccumulatedtimethesystemisrunning.
• Power-OffDelayDigitalTimer:Indicatesthelengthoftimeleftfordelayofffunction.
• Power-OffDelayTimerIndicator:Lightsupwhenauto-shutdowndelaytimerfunctionison.
• Controls:
• Automatic cleaning reminder:
• This range hood is equipped with a cleaning reminder that will activate following 30 hours of use.
Whenblower(motor)startstorotate,cumulativerunningtimewillbeshowninPower-On Elapsed
Digital Timer.Thistimericonasheswhen30hoursisupandremindsusertocleanthealuminum
lter.
• Aftercleaningthelterandwhenthemotorisnotinuse,pressandholdIncrease Value button over 3
secondstoresetthetimer.PleasenotethatturningoffthesystemwillnotresetthePower-On Elapsed
Digital Timer.
• Adjustingtheblower(motor)speed:
• PressPowerbuttononcetoturnonthesystem.TheBlower Power Indicatoriconashesshowingthat
theblower(motor)isready.Decrease Valuebuttonwilldecreasethespeedoftheblower(motor)from
6to1(strongesttoquietest).Increase Valuebuttonwillincreasethespeedoftheblower(motor)from
1to6(quietesttostrongest).
• PressPowerbuttononcetoturnoffthesystem.
Note: The system saves user congurations, settings such as light, timer and blower (motor) speed will
remain the same the next time it is turned on.

Page13
Elec. Control Panel Layout and Buttons
• Controls:
• Adjustingthetimerfunction:
• Whiletheblower(motor)isnotrunning,pressandholdDecrease Value button over 3 seconds to
entertimermode.AdjusttodesiredperiodofdelayofftimerbypressingIncrease Value or Decrease
Valuebutton(minimum1minutetomaximum15minutes).Thissettingwillbesavedimmediately.
• Activating the timer function:
• Whiletheblower(motor)isrunning,pressandholdPower button for over 3 seconds to activate
delayofftimer.Power-offdelayindicatorwilllitupandpower-offdelaydigitaltimerwillbeginto
countdown,whenitreacheszero,theblower(motor)willshutdown.
• Adjustingthelight:
• PressLight button once to turn on the lights, and once again to turn off the lights.
• While the lights are off, press and hold Light button for over 3 seconds to dim the lights from low to
high.Levelofbrightnesswillbestoredinsystem’smemory.
CAUTION: DO NOT touch the lights until switched OFF and cooled.
Note: Light settings are independent from other settings (including power-off delay) and lights has to be
manually turned on or off.
Note: The system saves user congurations, settings such as light, timer and blower (motor) speed will
remain the same the next time it is turned on.
Range Hood Operations (Continued)
Power
DecreaseValue
Light
IncreaseValue
BlowerPowerIndicator
BlowerSpeedIndicator
Power-OnElapsedDigitalTimer
Power-OffDelayDigitalTimer
Power-OffDelayTimerIndicator
LightPowerIndicator

Wiring Diagram
Six Speed with Type GU10 Bulb
Six Speed with Type MR16 Bulb
Page14

Troubleshooting
Page15
1. Iftherangehoodorhalogenlightdoesnotoperate
after installation:
• Checkiftherangehoodhasbeenpluggedin,make
surethatallpowerhasbeenturnedbackON,fused
notblownandallelectricalwiringareproperlycon-
nected.
• Swap out light assembly to working ones to
determinewhetheritiscausedbydefectivebulbs.
SeeReplacing the light bulbsonPage19.
2. The range hood vibrates when the blower is on: • The range hood might not have been secured prop-
erlyontotheceilingorwall.
3. Theblowerorfanseemsweak: • Checkthattheductsizedusedisatleast6”or3-1/4
x10”.RangehoodWILLNOTfunctionefciently
with insufcient duct size. For example: 8” duct
over6”holeandlooselysecured.
• Checkifductiscloggedorifdamperunit(half-cir-
cularapper)isnotinstalledcorrectlyoropening
properly.Atightmeshonasidewallcapunitmight
alsocauserestrictiontotheairow.
4. Thelightsworkbuttheblowerisnotspinningatall,
isstuckorisrattling.
• Theblowermightbejammedorscrapingthebot-
tomduetoshippingdamage.Pleasecontactusim-
mediately.
5. Thehoodisnotventingoutproperly: • Makesurethedistancebetweenthestovetopand
thebottomofthehoodiswithin*27”and30”in
distance.*Due to different ceiling height congura-
tions, recommended height may not be applicable.
• Reduce the number of elbows and length of duct
work. Check if all joints are properly connected,
sealed, and taped.
• Make sure the power is on high speed for heavy
cooking.
NOTE: For all other inquiries, please contact your local reseller.

Use and Care Information
Operations:
• Readandunderstandallinstructionsandwarningsinthismanualbeforeoperatingtheappliance.Savethese
instructions for future reference.
• Alwaysleavesafetygrillsandltersinplace.Withoutthesecomponents,operatingblowerscouldcatchonto
hair,ngersandlooseclothing.
• NEVERdisposecigaretteashes,ignitablesubstances,oranyforeignobjectsintoblowers.
• NEVERleavecookingunattended.Whenfrying,oilinthepancaneasilyoverheatandcatchre.Theriskof
self combustion is higher when the oil has been used several times.
• NEVERcookon“open”amesundertherangehood.Checkdeep-fryersduringuse:Superheatedoilmaybe
ammable.
Cleaning:
• Thesaturationofgreasyresidueintheblowerandltersmaycauseincreasedinammability.Keepunitclean
andfreeofgreaseandresiduebuild-upatalltimestopreventpossibleres.
• Filtersmustbecleanedperiodicallyandfreefromaccumulationofcookingresidue(seecleaning instructions
onPage19).Oldandwornltersmustbereplacedimmediately.
• DONOToperateblowerswhenltersareremoved.Neverdisassemblepartstocleanwithoutproperinstruc-
tions.Disassemblyisrecommendedtobeperformedbyqualiedpersonnelonly.Readandunderstandall
instructions and warnings in this manual before proceeding.
Page16
Specications
1.Onesoneisroughlyequivalenttothesoundofarefrigerator(1kHz)at40decibels.
2.Subjecttochangewithoutnotice,pleasecontactyourlocalresellerfordetails.
Specications*:
Body StainlessSteel
PowerRating 120V/60Hz(USA&Canadastandard)
GeneralInputPower 288W(218W+2x35W)
MotorInputPower 218W
Motor Revolution 600RPM(±10%)to1800RPM(±10%)
LevelsOfSpeedControl 6 Levels
MaximumAirow 650CFM
AirPressure 200pa
NoiseLevel(dB/sone) Approximately23/0.3to68/7.0(LowesttohighestSpeed)
MotorType Dual Chamber Ultra Quiet
FanType DualCentrifugal/Sirocco
ControlType 6SpeedElectronicControlPanelswithLCDDisplay
FiltrationType BafeFilter
Illumination 2x35WDimmable
VentingSize Top, 6 inches Round
InterferenceProtection RadioFrequencyInterferenceProtected

Measurements and Diagrams
• All measurements in parenthesis are in millimeter.
• All inch measurements are converted from millimeters, thus inch measurements are estimated.
Page17
Overall:

Page18
Rear Knockout Holes:
• All measurements in parenthesis are in millimeter.
• All inch measurements are converted from millimeters, thus inch measurements are estimated.
Measurements and Diagrams (Continued)