Videofied ITR110 User manual

Product Summary
The PIR Model ITR110/ITR600 is a wireless, indoor motion
detector designed for use in VIDEOFIEDTM security systems. The
detector includes the following features:
> Lithium batteries for long life.
> Standard coverage lens (12 m/40 ft. distance).
> Dual tamper function provides detection for both wall
and cover tamper.
> Transmits check-in/status signal every 8 minutes.
Installation Guidelines
For easier installation, programming and RF testing
should be done to check for good communication between
the control panel and all system devices before mounting
system devices. Install the detector and other system
devices in the following order:
>Programming/RF Testing - program detector
and all other devices into the control panel and test
RF communication from each intended device location
to the control panel.
>Mounting - mount detector at the tested location.
Programming/RF Testing
The following provides summarized steps for device
programming and testing. For complete details, refer
to the control panel installation manual.
1Loosen bottom screw, separate base
from detector and install battery.
2Re-attach base to secure tamper
switch.
3Put control panel into programming
/conguration mode.
4Using a programmed alphanumeric
keypad, proceed through menus until
the display shows RECORDING
DEVICES.
5Press YES. The display shows PRESS
PROGRAM BUTTON OF DEVICE.
6Press and release program button
on detector using a paper clip end.
The detector LED ashes. Wait for
keypad display to show DETECTOR
(1 - 24) RECORDED.
7Press YES. The display shows
RADIO RANGE TEST? Press YES
again. The detector LED starts
ashing and keypad display shows
TEST IN PROGRESS.
8Take detector to its intended mounting location and
make sure LED ashes continuously, indicating good
communication with control panel.
9Press YES to end radio range test, then press ESC/NO.
10 The display shows AREA ASSIGNMENT AREA:
1. Press either arrow button repeatedly until desired
AREA number appears, then press YES.
11 The display shows NAME + LOCATION. Enter appropriate
device name/location (up to 16 characters), then press
YES. The display shows the device number and name
for your verication.
12 Press YES. The display shows VERIFY DETECTION?
Press YES again and verify detector operation. For
example, wave your hand in front of detector to
activate its LED indicating detection.
13 Press YES to end detection verication.
14 The display shows ADD A NEW DEVICE?
Repeat steps 1 - 13 for remaining detectors.
15 When nished programming, put control panel
into operating mode.
www.videofied.com
Program Button
Screw
I N S T A L L A T I O N I N S T R U C T I O N S
PIR Model ITR110/ITR600
Manufactured by RSI VIDEO TECHNOLOGIES 1005-c July 2008

Mounting
> Use proper tools and hardware.
> Mount indoors in a temperature-controlled environment.
> Mount the detector 2.1 to 2.3 m (6.9 to 7.5 feet) from the oor.
> Mount the detector on an outside wall, aimed at area
to be protected.
> Do not aim detector at windows, especially those that
let in direct sunlight, or at heat sources such as lamps,
replaces, radiators, and heating vents.
> Do not aim detector at moving objects such as curtains,
fans, or animals in cages.
Regulatory Information
FCC Part 15
This device complies with FCC Rules Part 15.
Operation is subject to the following two conditions:
1.) This device may not cause harmful interference and,
2.) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by
RSI VIDEO TECHNOLOGIES can void the user’s authority to operate
the equipment.
Specifications
Panel Compatibility VIDEOFIED VISIO1000/V6000
Operating Frequency 868/915 MHz
Radio /type Spread Spectrum Bidirectional RF
Power Requirements One 3.6 V lithium battery
Battery Type LS14500
Detection Distance: 12 m/40 ft.
Angle: 90°
Operating Temperature 0°/+40°C (32°/104°F)
Maximum Relative Humidity 70%, non-condensing
Dimensions (LxWxD) 75 mm x 55 mm x 55 mm
3 in. x 2 in. x 2 in.
Weight 82 g/3 oz. (without battery)
Approvals CE / EN50131 (ITR110)
FCC (ITR600)
1Separate base from detector.
2Hold detector base against
mounting surface and mark the
two appropriate mounting holes.
3Drill pilot holes and install anchors
where needed.
4Mount detector base to surface
using appropriate screws
5Install battery into detector,
observing correct polarity.
6Place unit on the mounting surface so mounting holes
line up with pilot holes/anchors and secure the device
with the appropriate screws.
7Attach detector to base and secure with screw.
EMEA SALES
2, rue Alexis de Tocqueville
92160 ANTONY
FRANCE
Phone [phone]
Fax [phone]
© 2008 RSI VIDEO TECHNOLOGIES. VIDEOFIEDTM is a Registered Trademark of RSI VIDEO TECHNOLOGIES.
S2View®is a registered trademark of RSI VIDEO TECHNOLOGIES. Specications subject to change without notice.
USA SALES
4455 White Bear Parkway, Suite 700
White Bear Lake, MN 55110
USA
Phone [phone]
Fax [phone]
www.videofied.com
Flat Wall Mounting
Corner Mounting Holes
I N S T A L L A T I O N I N S T R U C T I O N SPIR Model ITR110/ITR600