ViewSonic VS12933 User manual

- User Guide
- Guide de l’utilisateur
- Bedienungsanleitung
- Guía del usuario
-Pyководствопользователя
- 使用手冊(繁中)
- 使用手冊(簡中)
VOT132
PC Mini
ViewSonic®
Model No. : VS12933

ViewSonic VOT132 i
Preface
Compliance Information
For U.S.A.
This device complies with part 15 of FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modications not expressly approved by the
party responsible for compliance could void your authority to operate the equipment.
For Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage
Directive 2006/95/EC.
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and
Electronic Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment as unsorted
municipal waste, but use the return and collection systems according to local
law.
If the batteries, accumulators and button cells included with this equipment, display
the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy
metal content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or
more than 0.004% Lead.
•
•
•
•

ViewSonic VOT132 ii
FCC Radiation Exposure Statement
This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
This wireless module device complies with part 15 of FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
Industry Canada Notice
This wireless module device complies with Canadian RSS-210.To prevent radio
interference to the licensed service, this device is intended to be operated indoors and
away from windows to provide maximum shielding. Equipment (or its transmitting antenna)
that is installed outdoors is subject to licensing. The installer of this radio equipment must
ensure that the antenna is located or pointed such that it does not emit RF eld in excess
of Health Canada limits for the general population; consult Safety Code 6, obtainable from
Health Canada’s web site www.hc-sc.gc.ca/rpb.
R&TTE Compliance Statement
This wireless module device complies with the Essential Requirements of the R&TTE
Directive of the European Union (1999/5/EC). This equipment meets the following
conformance standards:
ETSI EN 300 328
EN 301 489-01
EN 301 489-17
NotiedCountries:Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland,
France, Italy, Spain, Austria, Ireland, Portugal, Greece, Luxembourg, Estonia, Latvia,
Lithuania, Czech Republic, Slovakia, Slovenia, Hungary, Poland and Malta.
ENERGY STAR®information
The computer complies with the ENERGY STAR®requirements of less than 15 min of user
inactivity for the display and less than 30 min of inactivity for the computer.
Move the mouse or click any button on the keyboard to wake the computer from Sleep
mode.

ViewSonic VOT132 iii
Important Safety Instructions
1. Read these instructions completely before using the equipment.
2. Keep these instructions in a safe place.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this equipment near water. Warning: To reduce the risk of re or electric
shock, do not expose this apparatus to rain or moisture.
6. Do not block any ventilation openings. Install the equipment in accordance with the
manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other
devices (including ampliers) that produce heat.
8. Do not attempt to circumvent the safety provisions of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade and the third
prong are provided for your safety. If the plug does not t into your outlet, consult an
electrician for replacement of the outlet.
9. Protect the power cord from being tread upon or pinched, particularly at the plug, and
the point where if emerges from the equipment. Be sure that the power outlet is located
near the equipment so that it is easily accessible.
10. Only use attachments/accessories specied by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the equipment. When a cart is used, use caution
when moving the cart/equipment combination to avoid injury from tipping
over.
12. Unplug this equipment when it will be unused for long periods of time.
13. Refer all servicing to qualied service personnel. Service is required when the unit
has been damaged in any way, such as: if the power-supply cord or plug is damaged,
if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or
moisture, or if the unit does not operate normally or has been dropped.

ViewSonic VOT132 iv
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/95/
EC of the European Parliament and the Council on restriction of the use of certain
hazardous substances in electrical and electronic equipment (RoHS Directive) and is
deemed to comply with the maximum concentration values issued by the European
Technical Adaptation Committee (TAC) as shown below:
Substance Proposed Maximum Concentration Actual Concentration
Lead (Pb) 0,1% < 0,1%
Mercury (Hg) 0,1% < 0,1%
Cadmium (Cd) 0,01% < 0,01%
Hexavalent Chromium (Cr6+) 0,1% < 0,1%
Polybrominated biphenyls (PBB) 0,1% < 0,1%
Polybrominated diphenyl ethers (PBDE) 0,1% < 0,1%
Certain components of products as stated above are exempted under the Annex of the
RoHS Directives as noted below:
Examples of exempted components are:
1. Mercury in compact uorescent lamps not exceeding 5 mg per lamp and in other lamps
not specically mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, uorescent tubes, and
electronic ceramic parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight
or more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium
containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead
by weight.

ViewSonic VOT132 v
Copyright Information
Copyright © ViewSonic® Corporation, 2010. All rights reserved.
Microsoft®, Windows®, Windows NT®, and the Windows® logo are registered trademarks of
Microsoft® Corporation in the United States and other countries.
ViewSonic®, the three birds logo, OnView®, ViewMatch™, and ViewMeter® are registered
trademarks of ViewSonic® Corporation.
Intel®, Pentium®, and Atom™ are registered trademarks of Intel Corporation.
Award® is a registered trademark of Phoenix Technologies Ltd.
AMI® is a registered trademark of American Megatrends Inc.
ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency
(EPA).
As an ENERGY STAR® partner, ViewSonic Corporation has determined that this product
meets the ENERGY STAR® guidelines for energy efciency.
Disclaimer: ViewSonic® Corporation shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages resulting from
furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic® Corporation reserves the
right to change product specications without notice. Information in this document may
change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission from ViewSonic® Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it
becomes available, please register your product on the Internet at: www.viewsonic.
com. The ViewSonic® Wizard CD-ROM also provides an opportunity for you to print the
registration form, which you may mail or fax to ViewSonic®.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
VOT132
ViewSonic PC Mini
VS12933
VOT132-1_UG_ENG Rev. 1B 08-30-10
Product disposal at end of product life
ViewSonic respects the environment and is committed to working and living green. Thank
you for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn
more.
USA: http://www.viewsonic.com/company/green/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

ViewSonic VOT132
Table of Contents
Chapter 1 Introducing the VOT132
Top View........................................................................................................... 2
Front Side View................................................................................................ 2
Back Side View ................................................................................................ 3
Bottom View ..................................................................................................... 3
LED Indicator Introduction................................................................................ 4
Chapter 2 Connecting Peripherals
Placement of VOT132
On the Desk ................................................................................................. 6
On the Display Back..................................................................................... 6
Connection of VOT132
Connect the Antenna.................................................................................... 8
Connect the Monitor..................................................................................... 8
Connect the USB Devices............................................................................ 8
Connect the Network Cable ......................................................................... 9
Connect the Power Cord.............................................................................. 9
Chapter 3 BIOS Setup
Main Menu...................................................................................................... 11
Advanced Menu ............................................................................................. 12
Chipset Menu ................................................................................................. 14
Boot Menu ...................................................................................................... 15
Security Menu ................................................................................................ 16
Exit Menu ....................................................................................................... 17
Chapter 4 Installing Windows 7 onto the VOT132
Installing Windows 7....................................................................................... 19
Install Drivers in Windows 7 ........................................................................... 23
Appendix-Frequently Asked Questions .......................................................... 24
Appendix-Trouble Shooting............................................................................ 24
Chapter 5 Other Information
Customer Support .......................................................................................... 25
Limited Warranty ............................................................................................ 26

ViewSonic VOT132 1
Chapter 1
Introducing the VOT132
The VOT132 PC Mini is a compact and easy to use desktop. It features all the standard
PC capabilities but with a slim body design which enables you to do spreadsheets, cre-
ate documents, watch online content and browse the internet in a smarter and greener
way.
This chapter introduces VOT132’s PC Mini :
■ Top View
■ Front Side View
■ Back Side View
■ Bottom View
■ LED Indicator Introduction

ViewSonic VOT132 2
Introduction
The VOT132 PC Mini features all the desktop capabilities but with a slim body design which enables
you to browse the internet in a relaxed and comfortable way.
1-1 Top View
1-2 Front Side View
135mm
190mm
No. Name Description
1 Headphone Port Connects to headphones
2 Microphone In and S/PDIF In
Port
Connects to a microphone or playback devices with
optical connectors (3.5mm jack)
3 Multi-Function Card Reader Support SD/SDHC/MS/MS Pro/MMC memory cards
4 USB 2.0 Ports Connect to USB devices
5 LLS LED(1,2,3,4,5) Indicates system status
6 HDD LED Indicates hard disk status
7 Suspend Button Allows putting the system in suspend mode
8 Power Button with
Integrated LED Indicator
Turns the power on/off, indicates system status
123 5 874 6
25mm
LLS_LED1 LLS_LED5

ViewSonic VOT132 3
1-3 Back Side View
1-4 Bottom View
No. Name Description
1 Sheet Metal Replace sheet metal with ODD Connector
There are four magnet feet in the package. Just align them on the bottom of the
VOT132. The feet will then protect the VOT132 when it is placed on a desktop.
CAUTION
!
No. Name Description
1 RF(Radio Frequency) Port For connecting the antenna
2 USB 2.0 Ports Connects to USB devices
3 Display Output Port (DVI) Connects to display device
4 HDMI Port Connects to HDMI audio and video
5 Network Port Standard RJ-45 network port
6 Line Out and S/PDIF Out Port Connects to powered analog speakers or recording
devices with optical connectors (3.5mm jack)
7 Power Input Port Connects to the power adapter
1
1 3 5
476
2

ViewSonic VOT132 4
1-5 LED Indicator Introduction
Indication Power_
LED
HDD_
LED
LLS_
LED1
LLS_
LED2
LLS_
LED3
LLS_
LED4
LLS_
LED5
S0(Working Mode) Green - Off Off Off Off Off
S1(Power-Saving Mode) Green Off Off Off Off Off Off
S3(Standby Mode) Red Off Off Off Off Off Off
S4(Hibernation Mode)
&S5(System Power Off Mode)
Red Off Off Off Off Off Off
CPU
Initialization Error
- - Blue,
Blink
- - - -
DRAM Error - - - Blue,
Blink
- - -
BIOS Boot Block Fail - - - - - Blue,
Blink
-
BIOS
Checksum Error
- - - - - - Blue,
Blink
CMOS Cleared Red,
Blink
- - - - - -
HDD R/W Data - Red - - - - -
The LLS_LEDs status in this table only show BIOS error message.
CAUTION
!

ViewSonic VOT132 5
Chapter 2
Connecting Peripherals
In this chapter, the placement and the connection of some necessary peripherals will
be introduced.
This chapter includes the following information:
■ Placement of the VOT132
■ Connections of the VOT132

ViewSonic VOT132 6
2-1 Placement of the VOT132 PC Mini
1. On the Desk
1. Seat the unit in the desktop stand as shown to the right.
2. Mounted to the back of a display.
This is the best space-saving way.
1. Use four screws(M4*10, round head) to fasten the VESA mounting bracket to the back of
the display.
2. You can also place the VOT132 directly on the desktop.
Your display must have a 75mm x 75mm or 100mm x 100mm VESA mounting pat-
tern.
CAUTION
!

ViewSonic VOT132 7
2. Fit the VOT132 into the bracket with the power button located at the top for easy access.
3. After that, you can connect the antenna to the PC Mini.
2
1
To remove the VOT132 from the mounting bracket you must rst remove the antenna.
CAUTION
!

ViewSonic VOT132 8
2-2 Connection of VOT132
1. Connecting the Antenna
Connect the antenna to the RF port of the VOT132. You can then position the antenna and
rotate it in different positions.
2. Connecting the VOT132 to a monitor
Connect to the monitor thru the DVI connector.
3. Connecting USB Devices
Connect USB devices using the USB ports on the front or back, for example, mouse and key-
board.
2
1

ViewSonic VOT132 9
4. Conecting the network cable
Connect the LAN cable into the RJ-45 port with the other end connected to a hub or switch.
5. Connecting the power cord
Connect the power adapter to the power input port of the VOT132, and push the power button
to start it up.
Do not cover the power adapter while in normal use to allow normal heat dissipation.
CAUTION
!
or
Hub
Switch
2
Outlet
1
3

ViewSonic VOT132 10
Chapter 3
BIOS Setup
This chapter provides a description of the BIOS setup utility. The BIOS setup menus
and available selections may vary from those of your product. For specic information
on the BIOS for your product, please contact ViewSonic®.
The BIOS setup utility provides a built-in Setup program, which allows the user to
modify the basic system conguration and hardware parameters. The modied data
will be stored in a battery-backed CMOS, so that data will be retained even when the
power is turned off. In general, the information saved in the CMOS RAM will not need
to be changed unless there is a conguration change in the system, such as a hard
drive replacement or when a device is added. It is possible for the CMOS battery
to fail, which will cause data loss in the CMOS only. If this happens you will need to
recongure your BIOS settings.
This chapter includes the following information:
■ Main Menu
■ Advanced Menu
■ Chipset Menu
■ Boot Menu
■ Security Menu
■ Exit Menu

ViewSonic VOT132 11
Main Menu
The BIOS Setup is accessed by pressing the <F2> button after the Power-On Self-Test (POST)
memory test begins and before the operating system boot begins. Once you enter the BIOS
Setup Utility, the Main Menu will appear on the screen. The Main Menu provides System Over-
view information and allows you to set the System Time and Date. Use the “←” and “→” cursor
keys to navigate between menu screens.
Main Information Use [ENTER] ,[TAB],or [SHIFT-
TAB] to select a field.
Market Name : VOT132
Model Name : VS12933 Use [+] or [-] to
congure system Date.
System Date [Thu 08/06/2009]
System Time [09:44:21]
► SATA: [Hard Disk]
► System Information ← Select Screen
↑↓ Select Item
+/- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.
Advanced Chipset Boot Security Exit
BIOS SETUP UTILITY
Main
►SystemDate
<weekday><month><date> <year> format.
Day—weekday from Sun. to Sat., this message is automatically displayed by BIOS (Read
Only).
Month—month from 1 to 12.
Date—date from 1 to 31.
Year—year, set up by users.
Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to input the value.
►SystemTime
This item allows you to congure the desired time. Use [ENTER], [TAB] or [SHIFT-TAB] to
select a eld. Use [+] or [-] to input the value.
The three elds of the setting are <hour> : <minute> : <second> respectively.
►SATA
While entering setup, BIOS auto detects the presence of SATA devices. This displays the
status of auto detection of SATA devices. Press [Enter] to see the detailed information of
SATA device, such as vendor, size, LBA mode and so on.
►SystemInformation
Press [Enter] to go to the submenu. It dispalys the “BIOS Version”, “Processor Information”
and “System Memory Information”. All the information is read only.

ViewSonic VOT132 12
Advanced Menu
Advanced Settings Select the ACPI state used for
system Suspend
Suspend mode [S3 (STR)]
Legacy USB Support [Enabled]
Restore on AC Power Loss [Last State]
► Wakeup Conguration
► Onboard Device Conguration
← Select Screen
↑↓ Select Item
+/- Change Option
F1 General Help
F10 Save and Exit
ESC Exit
v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.
Main Chipset Boot Security Exit
BIOS SETUP UTILITY
Advanced
►Suspendmode[S3(STR)]
This item is used to set the energy saving mode of the ACPI function. When you select “S1
(POS)” mode, the power is always on and computer can be resumed at any time. When
you select “S3 (STR)” mode, the power will be down after a period of time. The status of the
computer before it entering STR will be saved in memory, and the computer can quickly
return to previous state when the STR function wakes.
►LegacyUSBSupport[Enabled]
This item is used to enable or disable the support for legacy USB. If no USB devices are
connceted, BIOS will automatically select [Disabled].
►RestoreonACPowerLoss[LastState]
This item is used to set which state the PC will take with when it resumes after an AC power
loss.
►WakeupConfiguration/OnboardDeviceConfiguration
Press <Enter> to go to relative submenu.

ViewSonic VOT132 13
Wakeup Configuration
Wakeup Configuration Disable/ Enable PCIE PME
to generate a wake event.
Resume on PCIE [Disabled]
Resume By RTC Alarm [Disabled]
Resume By USB KB/MS [Disabled]
← Select Screen
↑↓ Select Item
+/- Change Option
F1 General Help
F10 Save and Exit
ESC Exit
v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.
BIOS SETUP UTILITY
Advanced
►ResumeOnPCIE[Disabled]
This item is used to enable/disable PCIE PME to generate a wake event.
►ResumeByRTCAlarm[Disabled]
This item is used to enable/disable RTC Alarm to generate a wake up.RTC is system real
time clock.
►ResumeByUSBKB/MS[Disabled]
This item is used to enable/disable the keyboard/mouse to generate a wake up.