Viking Designer DFUW1441CR User manual

F20098C EN (042508J)
Viking Installation Guide
Professional Series Handle Kit
For Use with DFUD/DFWD/DFUR/DFUW/DFRI/DFRD/DFIM Models
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
[phone]
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com

3
DFWD - WARMING DRAWER
CUSTOM FRONT DIMENSIONS (Using Kit #PHK23)
CUSTOM FRONT INSTALLATION
1. Open the drawer and remove the pan.
2. Center the custom front on the inside panel.
3. Attach the custom front with the (6) six #8 x 3/4” screws provided.
Mounting Screws (4) - #8 x 3/4”
(6) - #8 x 3/4” screws
to attach custom
front
Cavity Assy.
Custom Front
A
B
11”
(27.9 cm)
1 3/8”
(3.5 cm)
1”
(2.5 cm)
DFWD170 DFWD100
A 26 1/2” 29 1/2”
(67.3 cm) (74.9 cm)
B 2 3/8” 3 7/8”
(6.0 cm) (8.6 cm)
DFUD - DISHWASHER
CUSTOM FRONT DIMENSIONS
(Using Kit #PHK23)
Custom Door
Front View
23 1/2”
(59.7 cm)
1” (2.5 cm)
7/8” 2.2 cm)
1 3/8” (3.5 cm)
29 3/4”
(75.6 cm)
3/4” Thick
(1.9 cm)
IMPORTANT-PLEASE READ AND FOLLOW
•Before beginning, please read these instructions completely and carefully.
•Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
•Please refer to the Installation Instructions for more information on installing the custom door fronts.
•The installer should leave instructions with the consumer who should retain for local inspector’s use and for future
reference.
Parts included: Required Tools:
Professional Series Handle Electric Drill Phillips Head Screwdriver
(2) End Caps Pilot Bit Masking Tape
(4) 1/4” x 1 1/4” Phillips Head Screws 1/4” (.6 cm) Drill Bit Pencil
Installation Instructions Counter Sink Drill Bit Tape Measure
Rubber Mallet
CUSTOM FRONT HANDLE INSTALLATION INSTRUCTIONS
To Install:
1. Place a handle encap on both ends of the handle tube. Tap the endcaps firmly into place with a rubber mallet
ensuring that both endcaps mounting surfaces are parallel.
2. Using the illustration provided, layout the handle location on the custom door. It is recommended that masking
tape be placed where the four holes will be drilled to help mark the hole placement and to prevent any damage to
the door when drilling the holes.
3. Before drilling, check handle against supplied dimensions. Drill small pilot holes completely through the door at
each of the four hole locations.
4. The Professional Series handle will be mounted using the screws provided. These screws require the holes to be
countersunk on the back of the panel in order for the door to fit flush against the panel. Using the four pilot holes
as guides, drill completely through the door in the four hole locations with a 1/4” (.6 cm) bit. Countersink the four
holes on the backside of the custom door panel.
5. Align the holes in the endcaps with the holes on the panel and attach the Professional Series handle to the panel
using the four screws provided.
2

DFRD - REFRIGERATED DRAWER
CUSTOM FRONT DIMENSIONS (Using Kit #PHK23)
DFIM - ICE MACHINE
CUSTOM FRONT DIMENSIONS (Using Kit #PHK23)
21 3/4” (55.2 cm)
C
L
10 7/8”
(27.6 cm)
1 3/8”
(3.5 cm)
1”
(2.5 cm)
NOTE: Hole locations are Typical as
above panel
21 3/4”
(55.2 cm)
1 3/8”
(3.5 cm)
5/8”
(1.6 cm)
9/16” (1.4 cm)
4
DFUR - BEVERAGE CENTER/DFUW - WINE CELLAR/
DFRI - COMBNATION BEVERAGE CENTER/ICE MAKER
CUSTOM FRONT DIMENSIONS (Using Kit #PHK30)
AA
9/16”
(1.4 cm)
5/8”
(1.6 cm)
29 1/16”
(73.8 cm)
1 3/8”
(3.5 cm)
1 3/8”
(3.5 cm)
TYP
Countersink
1/4” (0.6 cm)
O through holes
Front of Panel
5

76