Viking DrawerMicro VMOD241SS User manual

Viking Installation Guide
111 Front Street
Greenwood, Mississippi 38930 USA
DrawerMicro™ Oven
Control
Lock
Control
Lock
Start
Add-A-Minute
Sensor
Cook
Sensor
Cook
ReheatReheat
OPEN
CLOSE
Power
Level
Timer/
Clock
Stop/
Clear
334455
6677889900
Sensor
Reheat
Sensor
Reheat
DefrostDefrost
Sensor
Popcorn
Sensor
Popcorn
Setup/
Help
Setup/
Help
Keep WarmKeep Warm
1122
On/OOn/O
Control
Lock
Start
Add-A-Minute
Sensor
Cook
Reheat
OPEN
CLOSE
Power
Level
Timer/
Clock
Stop/
Clear
345
67890
Sensor
Reheat
Defrost
Sensor
Popcorn
Setup/
Help
Keep Warm
1 2
On/Off
VMOD241SS
DMOD241SS
Contro l
Lock
Start
Add-A- Minute
Start
Add-A- Minute
Sensor
Cook
Sensor
Cook
ReheatReheat
OPENOPEN
CLOSECLOSE
Power
Level
Power
Level
Timer/
Clock
Timer/
Clock
Stop/
Clear
Stop/
Clear
3 4 5
6 7 8 9 0
Sensor
Reheat
Defros t
Sensor
Popcorn
Setup/
Help
Keep Warm
1 2
On/Of f

E2
IMPORTANT–Please Read and Follow!
• Before beginning, read these instructions
thoroughly and carefully.
• Because the kit includes metal parts, caution
should be used in handling and installation to
avoid the possibility of injury.
• Do not remove permanently affixed labels,
warnings or plates from the product as this may
void the warranty.
• Observe all local and national codes, requirements
and ordinances.
• Installers should leave these instructions with the
consumer who should retain them for the local
inspector’s use and for future reference.
• For SAFETY CONSIDERATIONS do not install
drawer in any combustible cabinetry, which is
not in accord with the stated clearances and
dimensions on page 4, See FIGURE 1.
IMPORTANT SAFETY
INSTRUCTIONS
• WARNING: If the information in this manual is
not followed exactly, a fire or electrical shock
may result that could cause property damage,
personal injury or death.
• WARNING: To reduce the risk of tipping,
the DrawerMicro Oven must be secured by a
properly installed Anti-Tip block.
• This appliance must be electrically grounded in
accordance with local codes.
• Make sure the wall coverings and the cabinets
around the DrawerMicro Oven can withstand the
heat generated by the appliance.
• WARNING: Never leave children alone or
unattended in the area where a appliance is
in use. Never leave the drawer open when the
microwave is unattended.
• WARNING: Stepping, leaning or sitting on the
drawer may result in serious injuries and can also
cause damage to the appliance.
• Do not use the DrawerMicro Oven as a storage
space. This creates a potentially hazardous
situation.
• Check that the time-of-day is in the display. If not,
touch Stop/Clear to prevent unintended use.
DO NOT USE AN EXTENSION CORD WITH
THIS APPLIANCE. SUCH USE MAY RESULT
IN FIRE, ELECTRICAL SHOCK OR OTHER
PERSONAL INJURY.
ELECTRICAL GROUNDING INSTRUCTIONS
This oven must be electrically grounded in
accordance with local codes or, in the absence
of local codes, with the National Electrical
Code, ANSI/NFPA 70 – latest edition.

E3
Unpacking your
DrawerMicro Oven™
• Remove all packing materials from inside the
DrawerMicro Oven. DO NOT REMOVE THE
WAVEGUIDE COVER, which is located on the
top of the appliance.
Sealing Surface
Waveguide Cover
Oven Cavity
• Remove the feature sticker, if there is one. Check
the drawer for any damage, such as misaligned
or bent drawer, damaged drawer seals and
sealing surfaces, broken or loose drawer guides
and dents inside the cavity or on the front side
of the drawer. If there is any damage, do not
operate the appliance and contact your dealer
or a VIKING AUTHORIZED SERVICER.
Important Notes to the
Installer
• Read all of the Installation Manual before
installing the DrawerMicro Oven.
• Remove all packing material before connecting
the electrical supply.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the
consumer.
Important Notes to the
Consumer
Keep this manual with your Use and Care Manual
for future reference.
• As when using any microwave oven generating
heat, there are certain safety precautions you
should follow. These are listed in the Use and
Care Manual. Read all and follow carefully.
• Be sure your DrawerMicro Oven is installed and
grounded properly by a qualified installer or
service technician.

E4
DrawerMicro Oven
Measurements
• Dimensions that are shown in figure 1 must
be used. Given dimensions provide minimum
clearance. Locate electrical outlet in the shaded
area in the upper left-hand corner of the cutout.
See figure 4.
• Contact surface must be solid and level. Pay
special attention to the floor on which the
appliance will sit. The floor of the opening should
be constructed of plywood strong enough to
support the weight of the oven (about 100
pounds).
• Check location where the DrawerMicro Oven will
be installed for proper electrical supply.
• Your appliance can be built into a cabinet or wall
by itself or under a gas or electric wall oven.
• Be sure that the clearance of the floor between
the wall oven and the DrawerMicro Oven is a
minimum of 2".
• The microwave interior will easily accommodate
a 9" x 13" oblong dish or a bag of microwave
popcorn.
Anti-Tip Block
NORMAL INSTALLATION STEPS
Anti-Tip Block Installation Instructions
• To reduce the risk of tipping of the drawer, the
Anti-Tip block must be properly installed located
14-13/16" above the floor on which the appliance
will sit. The 6" Anti-Tip block must be provided
by the installer. See figure 1. The Anti-Tip block
prevents serious injury that might result from
spilled hot liquids.
36"
counter-
top
height
24"
cabinet min.
22 ¹⁄₈"
opening
14 ¹³₁₆"
opening
Allow
⁷₁₆"
overlap
Allow ¾"
overlap.
Allow ¾"
overlap.
19" to top
of floor
4"
5"
Electrical outlet location Anti-Tip
block
Floor must
support
100 lbs.
14 ¹³₁₆"
to bottom
of Anti-Tip
block
3 ¹⁄₂"
(6")
23 ½"
min depth
Allow ³₁₆"
overlap
21 ¹⁹⁄₃₂"
23 ³⁄₈"
14 ¹⁹⁄₃₂"
1 ³⁄₄"
door thickness
15 ⁵⁄₈ "
23 ⁷⁄₈"
15"
auto drawer
opening
1 ²³⁄₃₂"
4 ¹¹⁄₁₆"
DRAWERMICRO OVEN MEASUREMENTS: Figures 1 and 2
contain many DrawerMicro Oven measurements for reference
when planning the drawer’s location which can be installed
below any electric or gas wall oven. It can also be installed
using an electrical outlet in an adjacent cabinet within the
area where the provided electrical cord can reach. Power cord
access hole in cabinet should be a minimum 1½" diameter hole
and deburred of all sharp edges.
IMPORTANT: Always allow sufficient power cord length to the
electrical outlet to prevent tension.
DO NOT USE AN EXTENSION CORD. If the power supply cord
is too short, have a qualified electrician or serviceman install
an outlet near the appliance.
Always check electrical codes for requirements.
Clearances and Dimensions
2
1

E5
Drawer Installation
4"
(101.6 mm)
5"
(127 mm)
Electrical Outlet
Location
Anti-tip
Block
6"
(153 mm)
Mounting
Flange
DRAWER INSTALLATION: Place the DrawerMicro Oven
adjacent to the wall or cabinet opening. Plug the power supply
cord into the electrical outlet Carefully guide the appliance
into the prepared opening. Avoid pinching the cord between
the oven and the wall. Slide the drawer all the way until the
mounting flange is flush with the face of the cabinet. Open the
drawer. Using the 4 holes on the drawer as a template, pre drill
the cabinet using a 1/16" bit. See figure 5A. Secure the drawer
with the 4 screws supplied. See figure 5B.
• If the DrawerMicro Oven is ever moved to a
different location, the Anti-Tip block must also be
moved and installed. When installed to the wall,
make sure that the screws completely penetrate
the dry wall and are secured in wood or metal so
that the block is totally stable. When fastening, be
sure that the screws do not penetrate electrical
wiring or plumbing.
4"
(101.6 mm)
5"
(127 mm)
Electrical Outlet
Location
Anti-tip
Block
6"
(153 mm)
3
Electrical Outlet
• The electrical requirements are a 120 volt 60 Hz,
AC only, 15 amp. or more protected electrical
supply. It is recommended that a separate circuit
serving only this appliance be provided.
• The appliance is equipped with a 3-prong
grounding plug. It must be plugged into a
wall receptacle that is properly installed and
grounded. Should you only have a 2-prong
outlet, have a qualified electrician install a
correct wall receptacle.
Note:
If you have any questions about the grounding
or electrical instructions, consult a qualified
electrician or service person.
4 Screws
PARTS SUPPLIED
A
B
5
4

E6
GROUNDING
INSTRUCTIONS
This appliance must be grounded. In the event of
an electrical short circuit, grounding reduces the
risk of electric shock by providing an escape wire
for the electric current. The DrawerMicro Oven is
equipped with a cord having a grounding wire with
a grounding plug. The plug must be plugged into
an outlet that is properly installed and grounded in
accordance with the National Electrical Code and
local codes and ordinances.
WARNING: Improper use of the grounding plug
can result in a risk of electric shock. DO NOT USE
AN EXTENSION CORD. If the power supply
cord is too short, have a qualified electrician or
serviceman install an outlet near the appliance.
3-Prong Plug
Grounding Pin
3-Prong
Receptacle
Ground
Receptacle Box
PERMANENT AND CORRECT INSTALLATION
Care, Cleaning and
Maintenance
Refer to the Use and Care Manual for cleaning
instructions.
Model and Serial Number
Location
The name plate includes model number and
serial number. Open the Microwave Drawer fully.
The label is slightly beyond the back wall of the
microwave cavity facing up from the flat surface.
Before You Call for Service
Read the BEFORE YOU CALL and operating
instruction sections in your Use and Care Manual.
It may save you time and expense. The list includes
common occurrences that are not the result of
defective workmanship or materials in this range.
Refer to the warranty in your Use and Care Manual
for Viking’s toll-free service number and address.
Please call or write if you have inquiries about your
microwave product and/or need to order parts.
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
[phone]
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com