Viking EVSOF Single User manual

Installation Guide
Professional
Built-In 76 cm W. Electric Single Oven
French Door Single / Double Ovens

Table of Contents
Warnings & Important Safety Instructions _______________________________________3
Dimensions-76 cm Single _____________________________________________________6
Specifications 76 cm Single ___________________________________________________7
Cutout Dimensions 76 cm Single ______________________________________________8
Dimensions 76 cm French Door ______________________________________________12
Specifications 76 cm French door_____________________________________________13
Cutout Dimensions 76 cm French Door________________________________________14
General Information_________________________________________________________15
Installation _________________________________________________________________16
Final Preparation____________________________________________________________21
Performance Checklist_______________________________________________________21
Service & Registration _______________________________________________________23
2

3
IMPORTANT–Please Read and Follow!
• Before beginning, please read these
instructions completely and carefully.
• DO NOT remove permanently affixed
labels, warnings, or plates from product.
This may void the warranty.
• All local and national codes and
ordinances must be observed. Installation
must conform with local codes.
• The installer must leave these instructions
with the consumer who should retain for
local inspector’s use and for future
reference.
Your safety and the safety of others is
very important.
We have provided many important safety
messages in this manual and on your
appliance. Always read and obey all
safety messages.
This is the safety alert symbol. This
symbol alerts you to hazards that
can kill or hurt you and others.
All safety messages will be preceded by
the safety alert symbol and the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
Hazards or unsafe practices
which WILL result in severe personal
injury or death
DANGER
Hazards or unsafe practices
which COULD result in severe personal
injury or death
Hazards or unsafe practices which
COULD result in minor personal injury or
property damage.
All safety messages will identify the
hazard, tell you how to reduce the chance
of injury, and tell you what can happen if
the instructions are not followed.
WARNING
CAUTION
WARNING
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the
appliance by a person responsible for
their safety.
Children should be supervised to ensure
that they do not play with the appliance.

WARNING
To prevent possible damage to cabinets
and cabinet finishes, use only materials
and finishes that will not discolor or
delaminate and will withstand temperatures
up to 90°C. Heat resistant adhesive must
be used if the product is to be installed in
laminated cabinetry. Check with your
builder or cabinet supplier to make sure
that the materials meet these
requirements.
IMPORTANT–Please Read and Follow!
DANGER
ELECTRICAL SHOCK
HAZARD
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been properly
grounded in accordance with local codes.
WARNING
MOVING HAZARD
To avoid risk of severe
personal injury; this appliance
requires two or more personnel while
handling and moving. Possible use of
appliance moving devices is recommended.
WARNING
DO NOT use the handle or oven door to lift
the oven. Remove door before installation
to ensure that it is not used to lift the unit.
Make sure pins are inserted into hinges
before removing door to prevent injury to
hands and/or fingers.
WARNING
The misuse of the oven door(s) (e.g.
stepping, sitting, or leaning on them) can
result in hazards or injuries and damage to
the product.
WARNING
The use of cabinets for storage above the
oven may result in potential fire or burn
hazard.
WARNING
This appliance should not be used for
space heating. This information is based
on safety considerations.
4

5
WARNING
ELECTRICAL GROUNDING
INSTRUCTIONS
This oven must be electrically grounded in
accordance with local codes.
IMPORTANT–Please Read and Follow!
WARNING
Frame grounded by a 5 conductor cable
assembly. See “Installation Procedure”
section.
DO NOT USE AN EXTENSION CORD
WITH THIS APPLIANCE. SUCH USE
MAY RESULT IN FIRE, ELECTRICAL
SHOCK OR OTHER PERSONAL INJURY.
WARNING
This oven is heavy - use extreme care
when handling!
It is recommended that a thorough site inspection be
conducted PRIOR to unpacking and moving this appliance.
Site Preparation:
Wiring diagram is located on top of oven or in control panel.
Note:

Dimensions (76 cm Single Oven)
65.4 cm
52.1 cm
116.8 cm
74.9 cm
74.9 cm
20.3 cm
18.7 cm
13.6 cm
76 cm Wide
Rating Label
Location
6

Specifications (76 cm Single Oven)
EVESO Electric Oven
Description
30” W.
- 76 cm Wide
Overall Width 74.9 cm
Overall Height 74.9 cm
Overall Depth to edge of door—65.4 cm
with door open—116.8 cm
Cutout Width Standard—72.4 cm
Flush Mount—76.0 cm
Cutout Height Standard—71.4 cm
Flush Mount—77.2 cm
Cutout Depth Standard—60.9 cm
Flush Mount—65.4 cm
Electrical Requirements 5-wire ground, 240VAC, 30 amp electrical connection. Unit equipped
with No. 10 ground wire in unit. Fuse separately. 3 fuse 16 amps.
Maximum Amp Usage 21.0 amps—220 - 240V
Oven Interior Width 64.3 cm
Oven Interior Height 41.9 cm
Oven Interior Depth 42.7 cm
Oven Volume
(measured to AHAM standard)*
116 L.
Oven Volume (total oven cavity)
133 L.
Approximate Shipping Weight 118 kg
*The AHAM Standard for measuring oven capacity subtracts the door plug and convection baffle dimension from the
total oven volume.
7
L1 L2 L3 N T

Cutout Dimensions (76 cm Single Oven)
Note: A minimum of 5.1 cm spacing above and below the oven to any adjacent items is
required for ventilation purposes.
71.4 cm
Flush Mount
77.2 cm
43.2 cm
Min. to floor
60.9 cm
Flush Mount
65.4 cm
Make sure walls
are perpendicular
12.7 cm
10.2 cm
Junction
Box
Location
72.4 cm
Flush Mount
76.0 cm
76 cm Wide
Built-In
8
12.7 cm
10.2 cm
12.1 cm
72.4 cm
Flush Mount
76.0 cm
61.0 cm
Flush Mount
65.4 cm
71.4 cm
Flush Mount
77.2 cm
Make sure
walls are
perpendicular
Junction
Box
Location
76 cm Wide
Undercounter

Cutout Dimensions
(76 cm Single Oven flush mount installation)
9
Finished
Surfaces
ED
F
Vertical
Blocking
1.9 cm Bas
Blocking
LEGEND
Blocking
Finished
Surfaces
Note: To install the professional custom oven in a flush mount application the flush mount
accessory kit is required.
SINGLE OVEN
FLUSH CUTOUT
D76.0 cm
E65.4 cm
F77.2 cm

Cutout Dimensions
(76 cm Single Oven flush mount installation)
10
Vertical
Blocking
Distance will vary
depending on the
cabinet
C
ScrewScrew
B
A
CRITICAL
DIMENSIONS
A76.0 cm
B6.4 cm
C1.3 cm
Top View

11
Cutout Dimensions
(76 cm Single Oven Flush mount installation)
Vertical
Blocking
Base
Blocking
D
B
LEGEND
Blocking
Cabinet
Cross Section
CRITICAL
DIMENSIONS
B6.4 cm
D7.6 cm
Side View

Dimensions (76 cm French Door Oven)
12
65.4 cm
116.8 cm
57.2 cm
35.2 cm
74.9 cm
131.7 cm
(18.7 cm)
(14.0 cm)
(21.6 cm)
(65.4 cm)
(
100.6 cm)
(
35.2 cm)
(74.9 cm)
(64.9 cm)
EVDOF Double Oven
EVSOF Single Oven

13
Specification (76 cm French Door Oven)
EVSOF Single / EVDOF Double Oven
Description
EVSOF Single EVDOF Double
Overall Width 74.9 cm
Overall Height 64.9 cm 131.7 cm
Overall Depth to control panel—65.4 cm
with door open (Select/Premiere models)—116.8 cm
with door open (French Door model)—100.3 cm
Cutout Width Standard—72.4 cm
Cutout Height Standard—71.4 cm Standard—128.6 cm
Cutout Depth Standard—24” 60.9 cm
Electrical Requirements 4-wire ground, 240VAC, 60Hz, 50 amp electrical connection
Unit is equipped with No.10 ground wire in conduit.
Should be fused separately.
Maximum Amp Usage 40.0 amps—240 VAC, 60Hz
34.7 amps—208 VAC, 60Hz
Oven Interior Width–both ovens 64.3 cm
Oven Interior Height–both ovens 16-1/2” (41.9 cm)
Oven Interior Depth Single / Upper Oven:
42.7 cm - AHAM
49.5 cm - Overall
Lower Oven
42.7 cm - AHAM
49.5 cm - Overall
Oven Volume
(measured to AHAM standard)**
Single / Upper Oven:
121.8 L
Lower Oven:
116.1 L
Oven Volume
(Overall)
133.1 L
Approximate Shipping Weight 182 kg 182 kg
110°
90°
130°
110°
90°
130°
Door Swing

Cutout Dimensions (76 cm French Door Oven)
14
128.6 cm
72.4 cm
60.9 cm
12.7 cm
min.
10.2 cm
Junction
Box
Location
Make sure walls
are perpendicular
38.7 cm
min. to floor
*
*
EVDOF Double Oven
(71.4 cm)
(43.2 cm)
Min. to floor
(60.9 cm)
Make sure walls
are perpendicular
(12.7 cm)
(
10.2 cm)
Junction
Box
Location
(72.4 cm)
*
*
EVSOF Single Oven
EVSOF Single Oven
Undercounter
(12.7 cm)
(10.2 cm)
(12.1 cm)
(72.4 cm)
(61.0 cm)
(71.4 cm)
Make sure
walls are
perpendicular
Junction
Box
Location
*
*
*All French Door models must have a minimum of 45.7 cm (18”) clearance on
both sides to allow for door swing.
French Door models
can not be installed as a flush mount due to required door
clearance.

General Information
• All openings in the wall behind the
appliance or in the floor under the
appliance should be sealed.
• Keep appliance area clear and free from
combustible materials, gasoline and other
flammable vapors.
• Disconnect the electrical supply prior to
servicing or cleaning.
• When removing the appliance for cleaning
or service, disconnect AC power supply
and carefully remove the appliance by
pulling forward.
• CAUTION: The oven is heavy – use care
when handling!
• Electrical requirements are listed in the
product specifications under the electrical
requirements section.
Recommendations for
Unpacking
• Products are shipped on pallets with foam
footings and corrugated inner-packing and
exterior hoods.
• Products are anchored to the pallet using
metal straps that are screwed to the
bottom of the product and the pallet.
• DO NOT remove protective packaging
until you are ready to perform the
installation.
• To remove the packaging, first remove the
staples located at the bottom perimeter of
the corrugated cover.
• Remove the corrugated cover by lifting it
off the product and remove the inner-
packing.
• Detach the product from the metal anchor
strip by removing the attachment screw.
• DO NOT remove the protective wrapping
from the product control panel until the
product is installed.
Recommendations for
Moving
• The appliance is heavy – use extreme care
when handling!
• WARNING: DO NOT use the handle or
oven door to lift the oven. Remove door
before installation to ensure that it is not
used to lift the unit. Do not lift or carry
the door by the handle.
• Only proper equipment should be used to
move products.
• ALWAYS take steps to protect flooring at
the installation location when moving
products.
CAUTION
Avoid any damage to oven vents. The vents
need to be unobstructed and open to provide
proper airflow for optimal oven performance.
CAUTION
The cooling fan should be operating when
the unit is in operation. If you notice the
cooling fan is not operating or you observe
unusual or excessive noise coming from the
cooling fan, contact a Viking Authorized
Service Center before continuing operation.
Failure to do so can result in damage to the
oven or surrounding cabinets.
15

Site Preparation
Note: It is recommended that a thorough
site inspection be conducted PRIOR to
unpacking and moving this appliance.
• WARNING: DO NOT use the handle or
oven door to lift the oven. Remove door
before installation to ensure that it is not
used to lift the unit. Make sure pins are
inserted into hinges before removing door
to prevent personal injury to hands and/or
fingers. Do not lift or carry the door by
the handle.
• Confirm available access to adequate
power – see electrical requirements. Single
oven units require a 30 amp circuit.
Note: A minimum of 5.1 cm spacing above
and below the oven to any adjacent items is
required for ventilation purposes.
Installation
• It is recommended that 1.9 cm or larger
material be utilized to create a support
platform for this appliance.
• BE SURE that support for this appliance is
perpendicular to the front facing of the
wall or cabinet before you perform the
installation.
• Use of a hydraulic lift is recommended for
the installation of double oven units.
• All openings in the wall behind the
appliance or in the floor under the
appliance should be sealed.
• Keep appliance area clear and free from
combustible materials, gasoline and other
flammable vapors.
• WARNING: DO NOT USE AN
EXTENSION CORD WITH THIS
APPLIANCE. SUCH USE MAY RESULT IN
FIRE, ELECTRICAL SHOCK OR OTHER
PERSONAL INJURY.
1
2
Installation Procedure
Remove wooden brace on front of pallet. Open door completely. Place pin in pin hole.
16
Door removal is for standard electric and lower french door oven models.
DO NOT remove the single / upper double french doors during installation.

Unscrew pallet screws from side of oven. 3 Wire Connection
3
Remove hinge trim screws. Take off hinge trim.
5
Lift door up and out. Repeat for all doors.
Close until pins stop door.
6
Remove racks.
7
8a
step
L1
N
E
220-
240V
*Note: Check local code to see which wiring option should be used when grounding the unit.
Installation Procedure (continued)
4
17

Lift oven into position. Push oven straight in.
Attach screws to the side of the framing. Replace racks.
8b
step
L1 L2N
E
220-
240V
4 Wire Connection
8c
step
L1 L2 L3N
E
220-
240V
5 Wire Connection
9
10
11
12
*Note: Check local code to see which wiring option should be used when grounding the unit.
Installation Procedure (continued)
18

Replace door.
Take out pins.
Note: To adjust door turn adjustment screw
clockwise (up) or counterclockwise (down).
Close door.
Open door completely. Put hinge trim plates back on.
Note: Screw holes may need to be re-aligned.
13
14
15
16
Installation Procedure (continued)
19

20
Installation Procedure (French Door- Upper Door Adjustment)
There may be ocassions where the upper doors are not aligned to the same height, especially if doors
were removed for maintenance and then reinstalled. With doors in the closed position determine the
alignment required, for example right door is higher than left door.
Alignment procedure:
1. Open doors fully
2. Loosen bottom hinge screws on both doors, see photos below.
Using a 5/32” allen wrench, adjust screw on each door shown below moving the door that is too high
downward and the door that is low upward. You want to adjust both in opposite directions, not just
one door. Note that this moves the lower hinge assembly when adjusted.
Close doors and check alignment, when alignment is
correct, open doors and tighten the lower hinge plate
screws that you loosened at beginning of procedure.