Vimco Lutron Sivoia QED User manual

Sivoia QED™
Roller 64™
Dual Mount
Installation
Instructions

Notes:
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
SIVOIA QED TM Roller 64 Dual Mount 1
Installation Instructions

Sivoia QEDTM |Roller 64 Dual Mount
Installation Instructions
SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions
2
Tools Required:
Tape Measure 1/4” Hex-Head Driver
Wire Cutter/Stripper Level
Pliers Power Drill
#2 Phillips Screwdriver
(2) Sivoia QED™Roller 64
Left and Right Dual Brackets
(10) Mounting Screws
(#8x1-3/4" (#8x44mm) Hex Head Screws)
(2) 7 Pin Terminal Block
(Actual Size)
(1) Programming Stylus (1) Screwdriver
(4) 4” (102mm) Cable Ties
Notes:
1) Complete wiring and programming information can be found in the Sivoia QED Wire and
Programming Guide, P/N 045-038 or at www.lutron.com.
2) The Electronic Drive Unit (EDU) will need to be powered to complete installation.
Box Contents:
(4) Cable Tie Anchor

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 3
Warning: Incorrect installation can lead to severe injury, follow all installation instructions.
Notes:
• The Sivoia QED Roller 64 must be used only with window systems approved by Lutron.
• There must be a clearance of at least 1.3 feet (0.4 meters) between the fully lowered system
and any permanent object.
• Installation shall be executed by a qualified electrician according to national wiring rules.
• Before shade installation, remove any unnecessary cords and disable any equipment not
needed for powered operation. The Sivoia QED Roller 64 has a maximum rated operating
time of 8 min.
• The Sivoia QED Roller 64 must be used only with window systems approved by Lutron,
and should not be taken appart from the window system.
• Codes: Install in accordance with all local and national electrical codes.
• Environment: Ambient operating temperature: 0-40°C, 32-104°F, 0-90% humidity, non-condensing.
Indoor use only.
Sivoia QEDTM |Roller 64 Dual Mount
Installation Instructions (continued)

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions
4
1Confirm System Dimensions
1.1
1
System Width System Height
Compare system dimensions on
the package label with the window
dimensions to verify appropriate
window/shade combination.
1.1
Package Label

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 5
2Position the Mounting Brackets
Mark the location of the mounting brackets so they are centered over the window.
Note: Bracket to Bracket Distance = Fabric Width + 1.5” (38mm) = System Width.
Note: For a ceiling and jamb mount, allow clearance to prevent fabric from rubbing against trim, window,
top treatment, etc.
Note: Wall mount may require blocks (not provided) to clear trim.
2.1

3Pre-drill for Cable Run
SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 6
Choose one of the options below to drill for cable access.
Note: Cables may exit through any of the large holes in the dual brackets, on the EDU
side of the shades.
Note: Leave 12-18” (30-45 cm) cable exposed for each of the two shades.
3.1
DANGER - Locate and lock breaker to the shade power supply in the OFF position or
unplug the power plug-in transformer before doing any wiring.

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 7
4Install Dual Brackets
Install the first mounting bracket with the bracket oriented such that the upper shade
mount is closest to the glass.
4.1
Install the second mounting bracket as shown in the figure below.
Note: Each bracket should use four mounting screws, in either the ceiling holes or the wall holes.
Note: The brackets should be mounted to support at least 300 lbs (136 kg).
The fasteners provided may not be appropriate for use in all applications.
4.2
Upper and Lower
shade positions

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 8
5Wire 7-Pin Terminal Block
Strip 2” (50mm)
of jacket off the
cables that run
from the wall.
5.1
Wire 7-Pin terminal blocks (provided) to cables using the included screwdriver.
Note: SVQ-CBL-250 shown.
5.2

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 9
6Orient the Buttons and Wiring
Wire Slot
Buttons
For the following bracket and button orientations, route the wires as shown.
6.1
Note: The buttons should be accessible when the shade is installed.
Note: Make sure the wires are not pitched or damaged.
Note: The wires may go in either or both of the indicated slots.

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 10
7Mount the Shade
Install the idler side of the shade onto its bracket.
7.1
Depress the spring loaded idler by pressing the shade towards the idler, and install the EDU
side of the shade onto its bracket.
7.2

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 11
8Adjust the Shade
Ensure that the shade is level and centered by shimming the bracket.
Note: You do not need to level the second shade.
8.1
Adjust shade by removing the necessary screws and moving the brackets as needed.
Note: You may have to remove the shade to access the bracket screws.
8.2
Reinstall and tighten the screws.
8.3

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 12
9Connect Terminal Blocks
Plug 7-pin terminal block on cable into EDU terminal block (a cable tie can be used to secure the
terminal blocks together).
9.1
Dress wires to ensure fabric does not rub while the shade is moving.
9.2

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 13
IR Receiver Connection (if applicable)
Plug in the IR receiver.
Position the IR receiver.
Note: The IR receiver can not be covered from view of the remote control or
interfere with the shade.
Note: Dress wires to ensure the fabric does not rub while the shade is moving.
10
10.1
10.2

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 14
11 Secure and Check the Shade
Tighten retaining screws in each bracket to secure the shade.
11.1

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 15
Reconnect power to the shade power supply.
Use the programming stylus to run the shade up and down using the adjustment
buttons ( ), re-level if needed.
Observe: Pay careful attention to the shade roll up to ensure that it does not telescope
extremely to one side or the other.
Tip: Slight telescoping is normal. However, if the shade is telescoping severely to one
side and it is level, press the “Close Limit Button” ( ), and lower the shade all the way
down using the adjustment buttons ( ). Place a piece of tape on the side of the tube
that the fabric is telescoping away from when finished press the “Close Limit Button” ( )
once. This technique is referred to as “SHIMMING”. The shade will always track towards
the side that the tape (shim) is placed on.
11.2 Secure and Check the Shade (continued)

Press and hold the “Open
Limit Button” ( ) for 5
seconds. The green LED on
the roller shade EDU will
flash for 2 seconds, then go
dark, indicating that the
current position has been
stored as the Open Limit.
Adjust the position of the
EDU to the desired Open
Limit using the adjustment
buttons ( ).
Note: Setting the Open Limit lower than the Close Limit will cause the shade to move down when
raise is pressed and up when lower is pressed.
Setting the Open Limit from the EDU
12 Setting Limits from the EDU
Tap the “Open Limit Button”
( ), the green LED on the
roller shade EDU will turn on
steady, indicating that the EDU
is in “Set Open Limit Mode.”
12.1
12.2
12.3
SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 16

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 17
12.5
12.6
12.4
12 Setting Limits from the EDU (continued)
Setting the Close Limit from the EDU
Press and hold the “Close
Limit Button” ( ) for 5
seconds. The green LED on
the roller shade EDU will
flash for 2 seconds, then go
dark, indicating that the
current position has been
stored as the Close Limit.
Tap the “Close Limit
Button” ( ). The green
LED on the roller Shade
EDU will turn on steady,
indicating that the EDU is
in “Set Close Limit Mode”.
Adjust the position of the
EDU to the desired Close
Limit using the adjustment
buttons ( ).

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions 18
13 Install the Second Shade
Install the lower shade by repeating steps 6-12.
13.1

SIVOIA QEDTM Roller 64 Dual Mount
Installation Instructions
19
14 Finish System Programming
The Sivoia QED shade is now installed, wired, and the OPEN/CLOSE limits for each shade
have been set.
The next step is to finish programming the system.
Use the instructions in the Wiring and Programming Guide (p/n 045-038) or the Technical
Reference Guide (p/n 367-592) and perform these four easy steps:
1. Address the system. This gives each EDU, keypad and contact closure interface
in the system a unique address number or “name”, allowing proper communication
between components.
2. Verify wiring of each EDU, keypad and interface using the LED feedback from
each system component during addressing.
3. Assign shades (EDUs) to keypads, IR hand controls and/or contact closure
interfaces. Tell the system which shades (EDUs) respond to which keypads, IR
hand controls and contact closure interfaces.
4. Set and save PRESET shade positions if you desire them to be different from
the factory defaults.
Note: Before addressing, all keypads will operate all shades. This can be used to verify proper
wiring and communication.