VIPA System 300V User manual

Manual
VIPA System 300V
SM
Order no.: VIPA HB130E_SM
Rev. 07/44

Lerrzeichen

Manual VIPA System 300V
Subject to change to cater for technical progress.
The information in this manual is supplied without warranties. Information is
subject to change without notice.
© Copyright 2007 VIPA, Gesellschaft für Visualisierung und Prozess-
automatisierung mbH
Ohmstraße 4, D-91074 Herzogenaurach,
Tel.: [phone]
Fax.: [phone]
EMail: [email protected]
http://www.vipa.de
Hotline: [phone]
All rights reserved
The content of this manual was carefully examined to ensure that it
conforms with the described hardware and software.
However, discrepancies can not be avoided. The specifications in this
manual are examined regularly and corrections will be included in
subsequent editions.
We gratefully accept suggestions for improvement.
VIPA, System 100V, System 200V, System 300V and System 500V
are registered trademarks of VIPA Gesellschaft für Visualisierung und
Prozessautomatisierung mbH.
SIMATIC, STEP, ET200 and S7-300
are registered trademarks of Siemens AG.
Any other trademarks referred to in the text are the trademarks of the
respective owner and we acknowledge their registration.
Disclaimer of
liability
Trademarks

About this Manual Manual VIPA System 300V
Subject to change to cater for technical progress.
About this Manual
This manual describes the operation of the System 300V and the according
available signal modules (SM). A short overview over the range of products
is followed by a detailed description of the single modules. You will get
information for connecting and operating the System 300V and the
additional SM modules.
Chapter 1: Basics
This introduction includes recommendations on the handling of the
modules of the VIPA System 300V and introduces you to central res.
decentral automation systems.
Chapter 2: Installation and assembly guide lines
All information that you need for installation and cabling of a PLC with
components of the System 300V may be found in this chapter.
Chapter 3-5: Digital in-/output modules
These chapters introduce you to the digital peripheral modules of the
System 300V from VIPA and contain all information that you will need for
installation. Chapter 3 contains information about the digital input modules,
chapter 4 describes the digital output modules and chapter 5 concerns to
the combined input/output modules.
Chapter 6-7: Analog in-/output modules
Content of these chapters is the description of the analog peripheral
modules of the System 300V from VIPA. Chapter 6 gives you all necessary
information about the analog input modules and chapter 7 informs about
the analog output modules.
Overview

Manual VIPA System 300V Contents
HB130E - SM - Rev. 07/44 i
Contents
User considerations................................................................................. 1
Safety information.................................................................................... 2
Chapter 1 Basics.......................................................................................... 1-1
Safety Information for Users .............................................................................. 1-2
General description of the System 300V............................................................ 1-3
Components....................................................................................................... 1-4
Chapter 2 Assembly and installation guidelines...................................... 2-1
Overview ............................................................................................................ 2-2
Installation dimensions....................................................................................... 2-3
Installation at the profile rail ............................................................................... 2-4
Cabling ............................................................................................................... 2-6
Installation Guidelines ...................................................................................... 2-10
Chapter 3 Digital Input Modules................................................................. 3-1
System overview ................................................................................................ 3-2
321-1BH01 - DI 16xDC 24V............................................................................... 3-3
321-1BL00 - DI 32xDC 24V ............................................................................... 3-5
321-1FH00 - DI 16xAC120/230V ....................................................................... 3-7
Chapter 4 Digital Output Modules.............................................................. 4-1
System overview ................................................................................................ 4-2
322-1BF01 - DO 8xDC 24V 2A .......................................................................... 4-4
322-1BH01 - DO 16xDC 24V 1A........................................................................ 4-6
322-1BH41 - DO 16xDC 24V 2A........................................................................ 4-8
322-1BH60 - DO 16xDC 24V 0.5A for manual operation ................................ 4-10
322-1BL00 - DO 32xDC 24V 1A ...................................................................... 4-13
322-5FF00 - DO 8xAC 120/230V 2A ............................................................... 4-16
322-1HH00 - DO 16xRelay .............................................................................. 4-21
Chapter 5 Digital Input/Output Modules.................................................... 5-1
System overview ................................................................................................ 5-2
Security hints for DIO modules .......................................................................... 5-2
323-1BH00 - DIO 16xDC 24V 1A....................................................................... 5-3
323-1BH01 - DI 8xDC 24V, DO 8xDC 24V 1A................................................... 5-5
323-1BL00 - DI 16xDC 24V, DO 16xDC 24V 1A ............................................... 5-7
Chapter 6 Analog Input Modules................................................................ 6-1
System overview ................................................................................................ 6-2
Security hint........................................................................................................ 6-2
Parameterization - Basics .................................................................................. 6-4
331-1KF01 - AI 8x13Bit...................................................................................... 6-7
331-1KF01 - AI 8x13Bit - Parameterization ..................................................... 6-10
331-1KF01 - AI 8x13Bit - Technical Data......................................................... 6-14
331-7Kx01 - AI 8(2)x12Bit................................................................................ 6-17
331-7Kx01 - AI 8(2)x12Bit - Parameterization ................................................. 6-24
331-7Kx01 - AI 8(2)x12Bit - Diagnostics.......................................................... 6-29
331-7Kx01 - AI 8(2)x12Bit - Technical Data .................................................... 6-35
Chapter 7 Analog Output Modules............................................................. 7-1
System overview ................................................................................................ 7-2
Security hint........................................................................................................ 7-2
Connecting loads and actuators......................................................................... 7-4
Analog value representation .............................................................................. 7-5
Parameterization - Basics .................................................................................. 7-6
Diagnostics......................................................................................................... 7-9
332-5Hx01 - AO 2/4x12Bit U/I.......................................................................... 7-13
332-5HDx0 - AO 4x12Bit for manual operation ............................................... 7-18
Appendix
Index .................................................................................................................. A-1

Contents Manual VIPA System 300V
ii HB130E - SM - Rev. 07/44

Manual VIPA System 300V User considerations
HB130E - SM - Rev. 07/44 1
User considerations
This manual describes the signal modules (SM) that can be used with the
System 300. It contains a description of construction, project implemen-
tation and application of the products as well as the technical data.
The manual is targeted at users who have a background in automation
technology and PLC-programming.
This manual consists of chapters. Every chapter provides the description of
one specific topic.
This manual provides the following guides:
• An overall table of contents at the beginning of the manual
• An overview of the topics for every chapter
• An index at the end of the manual.
The manual is available in:
• printed form, on paper
• in electronic form as PDF-file (Adobe Acrobat Reader)
Important passages in the text are highlighted by following icons and
headings:
Danger!
Immediate or likely danger.
Personal injury is possible.
Attention!
Damages to property is likely if these warnings are not heeded.
Note!
Supplementary information and useful tips.
Objective and
contents
Target audience
Structure of the
manual
Guide to the
document
Availability
Icons
Headings

Safety information Manual VIPA System 300V
2 HB130E - SM - Rev. 07/44
Safety information
The modules of the System 300V are constructed and manufactured for
• System 300 components from VIPA and Siemens
• communication and process control
• general control and automation tasks
• industrial applications
• operation within the environmental conditions specified in the technical
data
• installation into a cubicle
Danger!
This device is not certified for applications in
• explosive environments (EX-zone)
The manual must be available to all personnel in the
• project design department
• installation department
• commissioning
• operation
The following conditions must be met before using or commissioning
the components described in this manual:
• Modification to the process control system should only be carried out
when the system has been disconnected from power!
• Installation and modifications only by properly trained personnel
• The national rules and regulations of the respective country must be
satisfied (installation, safety, EMC ...)
National rules and regulations apply to the disposal of the unit!
Application
specifications
Documentation
Disposal

Manual VIPA System 300V Chapter 1 Basics
HB130E - SM - Rev. 07/44 1-1
Chapter 1 Basics
Main theme of this chapter is to give you an overview about the System
300V from VIPA. We will outline the possibilities of the installation of
central res. decentral systems.
This chapter also contains general information about the System 300V like
measurements, hints for installation and the environmental conditions.
Below follows a description of:
• Safety information for the User
• Components of the System 300V
• General descriptions like measurements, installation, operating security
and environmental conditions
Topic Page
Chapter 1 Basics..............................................................................1-1
Safety Information for Users................................................................. 1-2
General description of the System 300V .............................................. 1-3
Components......................................................................................... 1-4
Outline
Content

Chapter 1 Basics Manual VIPA System 300V
1-2 HB130E - SM - Rev. 07/44
Safety Information for Users
VIPA modules make use of highly integrated components in MOS-
Technology. These components are extremely sensitive to over-voltages
that can occur during electrostatic discharges.
The following symbol is attached to modules that can be destroyed by
electrostatic discharges.
The symbol is located on the module, the module rack or on packing
material and it indicates the presence of electrostatically sensitive
equipment.
It is possible that electrostatically sensitive equipment is destroyed by
energies and voltages that are far less than the human threshold of
perception. These voltages can occur where persons do not discharge
themselves before handling electrostatically sensitive modules and they
can damage components thereby, causing the module to become
inoperable or unusable. Modules, damaged in this way, are normally not
immediately recognized. The according error may occur only after a while
of operation.
Modules that have been damaged by electrostatic discharges can fail after
a temperature change, mechanical shock or changes in the electrical load.
Only the consequent implementation of protection devices and meticulous
attention to the applicable rules and regulations for handling the respective
equipment can prevent failures of electrostatically sensitive modules.
Modules must be shipped in the original packing material.
When you are conducting measurements on electrostatically sensitive
modules you should take the following precautions:
• Floating instruments must be discharged before use.
• Instruments must be grounded.
Modifying electrostatically sensitive modules you should only use soldering
irons with grounded tips.
Attention!
Personnel and instruments should be grounded when working on
electrostatically sensitive modules.
Handling of
electrostatically
sensitive modules
Shipping of modules
Measurements and
alterations on
electrostatically
sensitive modules