Viper SL1610SE User manual

[866] 418-4737
[866] 41-VIPER Rev.00(05-06)
VV67149U
SERIAL #
VIPERINDUSTRIAL PRODUCTS
HAMILTON,MI 49419
P.O. BOX 104 VIPER...exceptional
value
MODEL # SL1610SE

CONGRATULATIONS on your purchase of a Viper product,
and welcome tothe V.I.P. family. We appreciate your
business and will do everything in our powerto keep you
happywithyour purchase formanyyears to come.
As part ofthe V.I.P. family, you are entitledtothe best
protection byone of the most comprehensive warranties in the
industry.
Thank-you forpurchasing Viper products!
Tom Vander Bie, CEO
TABLE OF CONTENTS
Machine Components 3
SafetyPrecautions 4
Machine Set Up5
Machine Operation 5-6
Machine Maintenance & Storage 6-7
Troubleshooting8
Parts Lists9-16
Wiring Diagram17

1
3
4
6
7
8
9
10
11
5
2
M
ACHINE COM
P
ONENTS
1) Vacuum / pump on/off switch
7) Sprayjets
2) Brush circuit breaker
8) Brush assembly
3) Brush / sprayon/off button
9) Pickup head
4) Drain hose
10) Solution tank fill port
5) Accessorytool solution hookup
11) Recoverytank lid
6) Br
ush raise and lower foot pedal

4
SAFETY PRECAUTIONS
GROUNDING INSTRUCTIONS
General This carped extraction machine
shall be grounded while in use to protect
the operator from electric shock. The
machine is provided witha three-contact
groundingtype attachment plugto fit the
proper groundingtype receptacle. The
green (orgreen &yellow) conductor in the
cord is the groundingwire. Never connect
this wire to other than the groundingpin of
the attachment plug.
This machine is for use on a nominal 120-
volt circuit and has a groundingplugthat
resembles the plugillustrated in figure
below. Make sure that the machine is
connected to an outlet havingthe same
configuration as the plug.No adapter
should be used with this machine.
This machine is intendedfor commercial
use. It is constructed foruse in an indoor
environment and is not intended for any
other use. Use onlyrecommended
accessories.
All operators shall read, understand and
exercise the followingsafetyprecautions:
1) Do not operate machine:
- Unless trained and authorized
- Unless you have read and
understand operators manual
- In flammable or explosive areas.
- With damaged or modified cord or
plug.
- If not in proper operatingcondition.
- In outdoor areas.
- In standingwater.
- Without filters in place.
- With the use of unapproved extension
cords.
2) Before operating machine:
- Make sure all safetydevices are in
place and operate properly.
3) When using machine:
- Mixand handle anychemicals
accordingto manufacturer’s
recommendations
- Do not run machine over cord.
- Do not pull machine bycord or plug.
- Do not pull cord around sharp edges
or corners.
-Do not unplug bypullingonthe cord.
- Do not stretch cord.
- Do not handle plugwith wet hands.
- Keep cord awayfrom heated
surfaces.
- Do not pick up flammable materials
or reactive metals.
- Report machine damage or faulty
operation immediately.
4) Before leaving or servicing machine:
- Turn off machine.
- Unplugpower cord from outlet.
5) When servicing machine:
- Unplugcord from outlet.
- Use manufacturer supplied or
approved replacement parts.
- Avoid movingparts. Don’t wear
loose clothing.

5
SLIDER EXTRACTOR SETUP
!!! Read operators manual thoroughly
prior to operating or servicing this
machine!!!
Carefullycheck the shippingcarton for
signs of damage. Report anycarton
damage to carrier immediately.
Check carton contents to ensure carton is
complete. Contact your Viper distributor if
anythingis missing.
Contents:
•Carpet Extractor
•Short bleeder”vacuum hose
•50’extension power cable
!!! Read operators manual
thoroughly prior to operating or
servicing this machine!!!
1) Usinga hose or bucket, fill tank with a
maximum of 10 gallons of hot water.
2) Add distributor recommended cleaning
solution
!!! Do not use flammable liquids or
operate machine in or near
flammable liquids or vapors!!!
3) Connect the supplied extension power
cable to the machine. Plugcord into a
grounded wall outlet. (see grounding
instructions)
4) Drop the brush head to the floor with
the foot release pedal on the back of
the machine.
MACHINE OPERATION
PRIOR TO EXTRACTING CARPETS
1) Inspect power cable and extension
cable for damage. Replace cable if
damage is found.
2) Vacuum carpet to remove debris prior
to extractingcarpet.
CARPET EXTRACTING
1) Turn on vacuum / pump switch.
NOTE: Solution will only spray when
the brush / spray button is pushed.
2) To start cleaning, push the brush /
spraybutton and begin topull the
machine backwards.
NOTE: For best cleaning results, pull
back on the machine at apace of
approx. 10 feet in 15 seconds.
3) Release brush / spraybutton at the end
of the path, and continue to pull
machine back for another 12 inches to
pick up excess solution.
4) Tip machine back onto the transport
wheels and push forwardto begin next
path.
OPERATING HINTS
1) Overlap cleaningpath byapprox. 2
inches
2) Work awayfrom power outlet and
power cable in order to avoid damage
to the power cable.

6
3) Continuallycheck for foam buildup in
recoverytank. Use a distributor
recommended foam control solution.
NOTE: Excessive foam buildup will not
activate the float shut-off and may cause
damage to the vacuum motor.
4) Repeat extraction path on heavily
soiled areas.
5) If brush stops spinning, there maybe
an obstruction in the brush. Unplugthe
power cable, raise the brush off the
floor and check for an obstruction.
Check & reset the brush circuit breaker
located on the control housing.
6) When recover of the dirtysolution ends,
or the solution tank is empty,you must
drain the recoverytank. (see TANK
DRAINING)
USE OF ACCESSORY TOOLS
NOTE: Prior to cleaning upholstery, be
sure to read cleaning instructions provided
by the manufacturer.
1) Disconnect black vacuum hose off the
back right side of the machine.
Connect (optional) accessoryvacuum
hose to area where the standard
vacuum hose was removed.
2) Connect (optional) accessorysolution
hose to brass quick connect coupler
located on the back of the machine.
3) Connect (optional) accessorytool to
solution and vacuum hoses.
4) Turn on vacuum / pump switch.
5) Operate accessorytools as needed.
6) When cleaningis completed, relieve
water pressure from solution lines by
turningoff vacuum / pump switch and
then squeeze trigger for 4seconds.
DRAINING TANKS
DRAINING SOLUTION TANK
1) Disconnect vacuum hose from back of
machine and connect the bleeder”
vacuum hose (included with machine)
to the machine back.
2) Remove the solution tank filter at the
fill area and place end of bleeder”
hose into the bottom of the tank.
3) Turn on vacuum / pump switch &
vacuum out the remainingsolution.
DRAINING RECOVERY TANK
1) Turn off machine, unplugand remove
power cable.
2) Unhook drain hose off the back of the
machine and remove drain hose
stopper.
3) Drain dirtysolution into floor drain.
4) Replace drain hose stopper and
reattach hose to back ofmachine.
MACHINE MAINTENANCE
To keep the machine performingwell
for manyyears, please follow the
followingmaintenance procedures.
!!! Always confirmthat the machine
is unplugged prior to performing
any maintenance or repairs!!!
DAILY MAINTENANCE
1) When cleaningoperation is complete
for the day, drain and rinse the
recoverytank thoroughlywith clean
water.
2) Remove remainingsolution from
solution tank.
3) Remove float shut-off (pingpongball
in cage) from recoverytank and clean
with water.

7
4) Remove and inspect brass sprayjets. If
necessary, clean jets in acetic acid
solution.
NOTE: Do not clean brass jets with a
pointed object, as it will damage the jets.
5) Check brush assembly& remove any
debris or carpet fibers.
6) Check pick up head and remove any
debris or carpet fibers.
7) Check condition of the stainless steel
pickup shoes on the pickup head. The
shoes must contact the floor for the
whole length of the pickup head.
Replace as necessary.
8) Clean machine with a nonabrasive
cleaner.
9) Inspect power cable for anydamage.
Replace if necessary.
MONTHLY MAINTENANCE
1) Flush pump & plumbingwith an acetic
acid solution to dissolve anychemical
buildup.
MixingInstructions:
a) Premix16 oz. or an acetic acid
solution with 2 gallons of water and
pour into solution tank.
b) Turn vacuum / pump switch on
c) Put machine head over floor
drain and operate machine for 50
seconds.
d) Shut machine down and allow
remainingsolution to sit in
machine overnight.
e) The followingday, sprayout
remainingsolution and flush
system again with 3 gallons of
clean water.
2) Inspect machine for water leaks.
3) Lubricate wheels with a water resistance
lubricant.
4) Check machine for loose or missing
nuts, screw and bolts andreplace as
necessary.
MACHINE STORAGE
1) Prior to storingthe machine, ensure the
solution and recoverytanks are clean
and emptyof anysolution.
2) Store machine in upright position in a
dryarea, with the brush head off the
floor.
3) Remove recoverytank clear lid to
allow for air circulation.
NOTE: If you are storing the machine in
an area which can freeze, be sure both
tanks and the solution plumbing are empty
of all water and dry!

BASIC TROUBLESHOOTING
PROBLEM CAUSESOLUTION
Machine doesn't
work Not plugged in to power sourcePlug into a grounded outlet
Faultypower cableContact Viper Distributor
Faultyextension power cableReplace with newextension power cable
Building circuit breaker trippedReset circuit breaker
Solution pump not
working Vacuum/ pump switch not onTurn on switch
Vacuum/ pump switch faultyContact Viper Distributor
FaultysolenoidContact Viper Distributor
Faultysolution pumpContact Viper Distributor
Pump overheated Determine cause and allow30 minutes for
pump to cool
Loose or broken wiringContact Viper Distributor
Vacuummotor not
working Vacuum/ pump switch not onTurn on switch
Vacuum/ pump switch faultyContact Viper Distributor
Vacuummotor thermal overload tripped
Checkfor obstruction and allow30 minutes
to cool
FaultyvacuummotorContact Viper Distributor
Worn carbon brushesContact Viper Distributor
Loose or broken wiringContact Viper Distributor
Poor pickup Air leaking around clear recoverylidEnsure recoverylid is firmlytightened
Clogged float shut-offRemove float shut-off and clean off debris
Float shut-off is activatedDrain recoverytank
Loose drain hose stopperEnsure stopper is securelyin place
Loose vacuumhose connectionsEnsure vacuumhose connections are tight
Defective vacuumhoseReplace vacuumhose
Loose vacuumhose cuffsEnsure cuffs are secure to the hose
Damaged or loose pickup head shoesContact Viper Distributor
Pulling machine too fastSlowdown cleaning operation
Uneven or no
solution spray Solution tankis emptyor lowFill solution tank
Vacuum/ pump switch not onTurn on switch
Dirtyor plugged spraytipsClean or replace spraytips
Improper spraytip size or sprayangleContact Viper Distributor
Worn spraytipsContact Viper Distributor
Faultysolution pumpContact Viper Distributor
Plugged solution tankfilterClean or replace filter
Pinched or kinked solution hose Checkfor obstructions and kinks and reroute
or replace ifneeded

DIA NO PART
NUMBER DESCRIPTION NO REQ'D
1VV96001SCLEAR DOME1
2VV60287AGASKET,CLEAR DOME1
3VF13491SCREW RHM M4X12 SST6
4VV67109BEND,TUBE1
5VV67301COUPLER1
6VV67302GASKET,COUPLER1
7VV67108ELBOW1
8VF81226COUPLER VAC HOSE1
9VV67705DRAIN HOSE1
10VV67113-1VAC HOSE1
11VV10113CLAMP,HOSE 2"2
12VV20509SCREW,RHM M5X10 SST4
13VV13601WASHER,LOCK,SST 52
14VV50712CLAMP,CORD3
15VV67503SWITCH1
16VV67509BUTTON,SWITCH1
17VV67504CIRCUIT BREAKER,2A1
18VF14126SCREW,M5X12,HEX3
19GV40215CORD WRAP1
20VV67111CLAMP,DRAIN HOSE1
21VV67501SWITCH HOUSING1
22VF99008STRAIN RELIEF 1
23VV13511 WASHER,TEETH, 32
24VF14212SCREW,M3X252
25VV67507CORD1
26VV67116POWER CORD2
27VV67505BUSHING,CORD,90 1
28VV13652NUT,LOCK,M32
29VV67508BRACKET,SWITCH1
30VV20291 WASHET,LOCK, 42
31VF13491SCREW,M4X122
32VF99023SWITCH ASSY1
33VV67105CONNECTOR1
34GT13032WASHER,PLAIN, 6X 16X1.51
35VV13607WASHER,LOCK,SST 61
36GT13056SCREW,M6X16,PH1
37VV80128BARB,HOSE1
38VV80115 ELBOW,STRECT 45 1
39VV80125ANUT,COUPLING1
40VV20667 WASHER,LOCK,INTERNAL TOOTH 1
PARTS LIST

DIA NO PART
NUMBER DESCRIPTION NO REQ'D
PARTS LIST
41VV60509GASKET,SOLUTION,INTAKE1
42VV20276WASHER,PLAIN 1
43VV80125COUPLING1
44VV10411STRAINER,LINE1
45VV67101SOLUTION TANK1
46VV67035ALOGO1
47VV67107FILTER1
48VA13471SCREW,ST5X102
49VV67102RECOVERY TANK1
50VF81504FLOAT, SHUT-OFF1
51VV67305BEND1
52VV96002BASEMENT,CLEAR DOME1

DIA NO PART
NUMBER
DESCRIPTION NO
REQ'D
PARTSLIST
1VV80208 COUPLER,QUICKCONNECT 1
2VV20274 WASHER,PLAIN, 13.5X 32X1.5 1
3VV20274A WASHER,PLAIN, 14X 32X1.5 1
4VV80115 ELBOW,STRECT,45 1
5VV80128 BARB,HOSE 2
6VV10114 CLAMP,HOSE,3/8" 6
7VV67114 HOSE,HIGH PRESSURE 1
8 VV67607 BARB,PUMP 1
9VV67604 SOLUTION SOLENOID,110V/60HZ 1
10 VV67606 CONNECTOR,THREE-WAY 1
11 VV67603 CONNECTOR 1
12 VV67602 BARB,PUMP 1
13 VV67601 MOUNTINGFRAME,PUMP 1
14 VV67605 PUMP,115V,100PSI 1
15 VF81503 GASKET,VACMOTOR 1
16 VV67154 VACMOTOR,3-STAGE,120V 1
17 GT13032 WASHER,SST,PLAIN, 6X 16X1.5 11
18 VV80210 BEND,NYLON,PUMP 1
19 VV67117 HOSE,SOLUTION 1
20 VF13521 NUT,SST,M6 6
21 VF81508 STUD 3
22 VF13502 NUT,LOCK,M6 3
23 VV10113 CLAMP,HOSE 2" 3
24 VV67152 EXHAUSTHOSE, 48 1
25 VF13495 BOLT,M6X16,HEX 2
26 VV13607 WASHER,LOCK, 611
27 VF13551 WASHER,SST,PLAIN, 6X 22X1.5 2
28 VF82028 CABLE 1
29 VV67104 SPACER 2
30 VF13512 SCREW,FH,M5X15,SST 8
31 VV60406S HINGE,SST,4" 2
32 GT13058 SCREW,FH,SST,M5X22 6
33 GT13056 SCREW,SST,PH,M6X16 4
34 VF13474A WASHER,SST,PLAIN, 5X 15X1 10
35 VV13601 WASHER,LOCK, 510
36 VV13633 NUT,SST,M5 7
37 VV67140 CARPETPICK-UP TOOL 1
38 VV67142 STAINLESS STEELSHOES 2
39 VV67407 SPRING 1
40 VV67400 MOUNTINGBASE ASSY,BRUSH 1
41 VV67110 SHOULDERSCREW 2

DIA NO PART
NUMBER
DESCRIPTION NO
REQ'D
PARTSLIST
42 VV67115 HOSE,SPRAYING 1
43 VV67120 CLAMP 1
44 VA13473 SCREW,RHM,M4X16,SST 1
45 VV67405 STRAINER 1
46 VV13635 SCREW,RHM,M5X20,SST 1
47 GT13014 NUT,NYLON,INSERT,M4 2
48 VV67106 SPACER 4
49 VA13478 SCREW,M6X35,HEX 1
50 VV67103A FOOTSTEP 1
51 VF14127 SCREW,RHM,M6X20,SST 2
52 VV67121 ANTISKIDPLATE 1
53 VV60113S WASHER,WHEEL,AL 2
54 VA75004 WHEEL,10" 2
55 VF13604 WASHER, 5 1
56 VV13634 SCREW,RHM,M5X30,SST 4
57 VV67200 BOTTOMPLATE,ASSY 1
58 VV67505 BUSHING,90º,CORD 1
59 VF143001 SCREW,PH,M3X4,SST 4

DIA NO PART
NUMBER DESCRIPTION NO REQ'D
PARTS LIST
1VV67403-2ALIFT BAR1
2VV99926-1RECTIFIER1
3VV13601WASHER,LOCK,SST, 55
4VV13633NUT,SST,M55
5VV13634SCREW,SST,PH,M5X30 1
6VA13475SCREW,PH,SST,M5X252
7VV67407SPRING1
8VV20501SCREW,PH,SST,M5X142
9VV13662WASHER,PLAIN, 5X 12X16
10VV67401MOUTING BASE,BRUSH1
11VV80128BARB,HOSE1
12VV67423INSERT,SPRAYER BODY2
13VV67421SPRAYER BODY1
14VV67422SPRAY TIP4
15VV67435MOTOR,110V1
16VV67433GASKET1
17VV67431-1BOTTOM PLATE1
18GT13054SCREW,BH,M5X12,SST10
19VF13512ASCREW,FH,SST,M5X184
20VV67412BRUSH1
21VV67417GASKET2
22VV67414FRAME,BRUSH2
23VV67404PLATE1
24VV67406GASKET1
25VF14024BEARING2
26VF14023SEAL2
27VV67411SHAFT,BRUSH1
28VV67413AXLE,PULLEY1
29VV67416SPACER1
30GT13059SCREW,HEX,SOCKET4
31VV67415DRIVEN PULLEY1
32VV67402BELT1
33VV67432DRIVING PULLEY1
34VV67424NOZZLE BODY4
35VV67436 MOUNTING BRACKET MOTOR 1
36GT13032WASHER,SST,PLAIN, 6X 16X1.54
37VV13607WASHER,LOCK, 64
38VF13521NUT,SST,M64
39VV67405STRAIN RELIEF1
40VV67408POWER CORD1