Visonic MCT-212 User manual

D-302054 1
MCT-212
PowerCode Wrist/Pendant Transmitters
User Guide
1. INTRODUCTION
The MCT-212 is a miniature, waterproof, UHF transmitter,
designed for use in advanced, high-security alarm and remote
control systems. Transmission is activated by depressing the
recessed pushbutton at the center of the unit. When activated,
the transmitter sends out a 24-bit ID code and an alarm code,
identifiable by compatible wireless receivers of the PowerMax
family. Each transmitter's code is randomly selected in the factory
from 16 million possible combinations. The code is therefore
unique and virtually impossible to reproduce.
Operating power is obtained from an internal 3-volt Lithium
battery.
All MCT-212 are supplied with a wrist band and neck strap. They
can be worn on the wrist or around the neck.
The LED (see Fig. 1) lights during a transmission to indicate a good
battery. If the LED flashes during a transmission, this means that the
battery voltage is low and since the transmitter is hermetically sealed
the transmitter should be replaced by a new transmitter. Anytime the
MCT-212 is pressed when the battery is low, a trouble signal is
automatically sent to the compatible wireless receivers of the
PowerMax family.
LED indicator
Velcro strap
Transmit
Button
Loop
Safety release
mechanism
Neck cord
Velcro strap
Figure 1. MCT-212
The transmitter case is waterproof, hermetically sealed (no screws)
and therefore disposable. Do not attempt to open the transmitter
case or replace the battery; such action will void the warranty.
2. SPECIFICATIONS
Frequency (MHz): 315 or other frequency according to local
requirements.
Modulation: ASK (ON-OFF keying)
Transmitter ID: 24 bit digital word. Over 16 million possible code
combinations, pulse width modulation.
Toatl Message Length: 36 bits
Minimum Transmit Duration: 2 sec
Power Supply: 3-volt Lithium cell type CR-2032
Battery Life Expectancy: 3 years (for typical use)
Caution! Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the manufacturer's instructions.
Battery Supervision:
Good battery - LED lights steadily upon activation.
Low battery - LED flashes upon activation.
Note: If transmission is still possible despite the battery condition,
the MCT-212 will send a low battery report to the receiver.
Operating Temperature: 0° to 50°C (32° to 122°F).
Dimensions: 39 x 37 x 13 mm (1-9/16 x 1-7/16 x 5/8 in.).
Compliance with standards: UL 1023, UL 985 (UL file S9102)
Weight: 25 g (0.9 oz).
Color: Gray
This device complies with Part 15 of the FCC Rules and RSS-210
of Industry and Science Canada. Operation is subject to the
following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
3. ENROLLING AND TESTING
3.1 Enrolling
For proper function of the transmitter, its ID must be enrolled into
the compatible wireless receiver of the PowerMax family.
"Teach" the target receiver the ID code of the tested transmitter, as
instructed in the target receiver's installation manual.
3.2 Testing
A. Stand 3 m (10 ft) away from a target receiver and operate the
MCT-211 by depressing its transmit pushbutton. Verify that the
transmitter LED lights, indicating good battery condition.
Note: The LED will light for 2 seconds even if you press the
button for a shorter duration.
B. Verify that the received signal at the compatible PowerMax
system is STRONG or GOOD (see compatible PowerMax system
installer guide – DIAGNOSTIC TEST).
C. Operate the transmitter from various locations within the area
covered by the target receiver to determine "dead" locations,
where transmission is blocked by walls and large objects, or
affected by structural materials.
Note: If dead/marginal zones are a problem, relocating the
receiver may improve the performance.
4. PRODUCT LIMITATIONS
Our wireless systems are very reliable and are tested to high
standards. However, due to their low transmitting power (required
by FCC, DTI and other regulatory authorities) there are some
limitations to be considered:
A. Receivers may be blocked by radio signals occurring on or near
their operating frequencies, regardless of the code selected.
B. A receiver can only respond to one transmitted signal at a
time.
C. Wireless equipment should be tested regularly (at least once a
week) to determine if there are sources of interference and to
protect against faults.

2 D-302054
WARRANTY
Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only (the
“Purchaser”) against defective workmanship and materials under normal use of the Product for a period of twelve
(12) months from the date of shipment by the Manufacturer.
This Warranty is absolutely conditional upon the Product having been properly installed, maintained and operated
under conditions of normal use in accordance with the Manufacturers recommended installation and operation
instructions. Products which have become defective for any other reason, according to the Manufacturers
discretion, such as improper installation, failure to follow recommended installation and operational instructions,
neglect, willful damage, misuse or vandalism, accidental damage, alteration or tampering, or repair by anyone
other than the manufacturer, are not covered by this Warranty.
The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the
Product will prevent any death and/or personal injury and/or damage to property resulting from burglary, robbery,
fire or otherwise, or that the Product will in all cases provide adequate warning or protection. The Product,
properly installed and maintained, only reduces the risk of such events without warning and it is not a guarantee
or insurance that such events will not occur.
THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE. IN
NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES
WHATSOEVER, AS AFORESAID.
THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS
OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM
PURCHASER’S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF
OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY
INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION.
However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising under this
limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE
EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated damages and not as a
penalty, and shall be the complete and exclusive remedy against the Manufacturer.
When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and warranty and
he recognizes having been informed of.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so these
limitations may not apply under certain circumstances.
The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning of any
telecommunication or electronic equipment or any programs.
The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the
Manufacturer’s discretion any Product or part thereof that may prove defective. Any repair and/or replacement
shall not extend the original Warranty period. The Manufacturer shall not be responsible for dismantling and/or
reinstallation costs. To exercise this Warranty the Product must be returned to the Manufacturer freight pre-paid
and insured. All freight and insurance costs are the responsibility of the Purchaser and are not included in this
Warranty.
This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to
act on its behalf in the modification, variation or extension of this warranty. This warranty shall apply to the
Product only. All products, accessories or attachments of others used in conjunction with the Product, including
batteries, shall be covered solely by their own warranty, if any. The Manufacturer shall not be liable for any
damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or otherwise, caused by the
malfunction of the Product due to products, accessories, or attachments of others, including batteries, used in
conjunction with the Products. This Warranty is exclusive to the original Purchaser and is not assignable.
This Warranty is in addition to and does not affect your legal rights. Any provision in this warranty which is
contrary to the Law in the state or country were the Product is supplied shall not apply.
Warning: The user must follow the Manufacturer’s installation and operational instructions including testing the
Product and its whole system at least once a week and to take all necessary precautions for his/her safety and
the protection of his/her property.
1/08
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not
returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.
Directive 2002/96/EC Waste Electrical and Electronic Equipment.
The technical documentation as required by the European Conformity Assessment procedure is kept at:
UNIT 6 MADINGLEY COURT CHIPPENHAM DRIVE KINGSTON MILTON KEYNES MK10 0BZ. Telephone number: 0870 7300800, Fax number: 0870 7300801
VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: [phone], FAX: [phone]
VISONIC INC. (U.S.A.): 65 WEST DUDLEY TOWN ROAD, BLOOMFIELD CT. 06002-1376. PHONE: [phone]. FAX: [phone]
VISONIC LTD. (UK): 7 COPPERHOUSE COURT, CALDECOTTE, MILTON KEYNES. MK7 8NL. TEL: [phone] FAX: [phone]
PRODUCT SUPPORT: [phone]
VISONIC GmbH (D-A-CH): KIRCHFELDSTR. 118, D-40215 DÜSSELDORF, TEL.: [phone], FAX: [phone]
VISONIC IBERICA: ISLA DE PALMA, 32 NAVE 7, POLÍGONO INDUSTRIAL NORTE, 28700 SAN SEBASTIÁN DE LOS REYES, (MADRID), ESPAÑA.
TEL [phone], FAX [phone]. www.visonic-iberica.es
INTERNET: www.visonic.com
©VISONIC LTD. 2010 MCT-212 D-302054 (Rev 1, 3/10)