Vista VM215 User manual

VM215 LED Monitor Quick Guide Ver 1.0 2023-06-13
21.5” LED Monitor

1
Before You Begin
Please read this guide before installing or operating the product. You must have knowledge of
CCTV, IT and electrical wiring and products.
Technical Support
If you still have questions after referring to the guide, or require more information, please contact
Vista Technical Support or use the QR code.
Vista Technical Support [phone]
Norbain SD, Inspired, Easthampstead Road, Bracknell, Berkshire RG12
1YQ
* WARNING: Improper use can cause severe bodily injury or
equipment damage.
This guide is intended for use with the Vista VM215 LED 21.5” Monitor.
1. Packing List
Please contact Norbain if any items are missing or damaged and note contents will vary according
to each camera model number.
➢Monitor
➢Pedestal
➢Power cable
➢HDMi cable
➢QR Code label1
*1Scan in order to access the Vista website for product info and this quick guide

2
2. Safety & Maintenance Instructions
•Use only correctly rated PSUs supplied with the device.
•Do not use this apparatus near water.
•Do not install near any heat sources such as radiators, stoves, or other apparatus (including
amplifiers) that product heat.
•Do not block any ventilation openings.
•Protect the power cord from being walked on or pinched.
•Only use attachments/accessories specified by the manufacturer.
•Unplug this apparatus during lightning storms.
•Refer all servicing to qualified service personnel only. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid spillage etc.
CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE
BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE
THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY
SERVICING OTHER THAN THAT CONTAINED IN THE
OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED
TO DO SO.
3. Connecting The Monitor
Follow the below to connect your monitor correctly.
Caution: First, turn off and disconnect any power to be used for this device!
- Determine if you will be using HDMi or VGA to connect to the device that you wish to
display on the VM monitor. Connect the relevant cable.
- Determine if an audio connection is required to Audio In via a 3.5mm audio jack plug
and lead. Note: if using HDMi, then it may be possible audio could be caried via that
cable instead.
- Now connect and turn on power to the monitor and your connected device if needed.
- Refer to the next section –Main Menu Settings.

3
4. Main Menu Settings
Control buttons are located on the bottom left of the bezel and detailed below.
"Source" button: Press to display OSD with all possible signal inputs.
Press button again to change the selected function in 0SD menu.
"Downward" button: Press to move the cursor downwards in any menu.
"Upward" button: Press to move the cursor upwards in any menu.
"Menu" button: Press to display the 0SD main menu.
Press again to Exit.
"Power" button: Press to turn on or turn off the display
The sub-menus of the main menu are detailed below: PC Menu, Picture menu, Audio menu, OSD
menu and Function menu.
Press the menu button to select the sub-menu item. The selected menu item will show a bordered
wireframe. Press the .6. T button to move among the secondary menu items of the sub-menu.
PC MENU (PC SOURCE)
PC menu sets the contrast, brightness, backlight,
colour temperature and scale function. Press
buttons to adjust each value whilst selected,
press to exit.

4
BRIGHTNESS MENU
Sets the brightness, contrast, black equalizer, low
blue, eco and OCR function.
Press buttons to adjust each value whilst
selected, press to exit.
IMAGE MENU
IMAGE menu can set H. POSITION, V.
POSITION, CLOCK, PHASE and ASPECT
function.
Press buttons to adjust each value whilst
selected, press to exit.
COLOR TEMP. MENU
COLOR menu can set COLOR TEMP. function.
Press buttons to adjust each value whilst
selected, press to exit.
OSD SETTING MENU
OSD SETTING menu can adjust LANGUAGE,
OSD H. POS, OSD V. POS, OSD
TIMER and TRANSPARENCY function.
Press buttons to adjust each value whilst
selected, press to exit.
RESET MENU
RESET menu can set IMAGE AUTO ADJUST,
COLOR AUTO ADJUST, RESET,
AUTO POWERDOWN and TIMECOUNT
function.
Press buttons to adjust each value whilst
selected, press to exit.
MISC. MENU
MISC. Menu can adjust SIGNAL SOURCE,
MUTE and VOLUME function.
Press buttons to adjust each value whilst
selected, press to exit.

5
5. Troubleshooting
Before consulting with Vista Support, please use the following chart to attempt to diagnose any
issue.
Problem
Fix
1
2
3
4
5
6
7
8
9
10
No image or sound
Inferior sound, normal image
Inferior image, normal sound
Poor signal
Vague image
Double image
Interfering lines in image
Twisty image
Poor signal
Rung stripe in image
Image vertically scrolls
Inferior colour
No colour
Fix
1
Switch to another channel or input and compare.
2
Check the audio signal line is connected.
3
Check the video signal line is connected.
4
Interference from another electric appliance may be present.
5
Adjust fine tuning setting.
6
Adjust luminance setting.
7
Adjust contrast ratio setting.
8
Adjust colour setting.
9
Check whether the system is set-up correctly.
10
Check whether the power is on.

6
How to Clean Product
1. Please wipe off dust and other particles with a clean, soft towel.
2. If still not clean, use a neutral cleaner wipe dry.
3. Rubbing or scrapping the housing, with fingernails or other hard objects, may scratch the
housing.

7
Where applicable, a Declaration of Conformity in accordance with Directives 2014/30/EU (EMC), 2014/35/EU
(LVD), and 2015/863/EU RoHS(3) has been made and we declare the product compliant.
Where applicable, the requirements of the European law on the Restriction of Hazardous Substances (RoHS)
directive: 2015/863/EU have been met and the product is without the hazardous substances cited in the
directive.
Our CE EU-Authorised Representative: Comply Express Unipessoal LDA, StartUp Madeira - EV141,
Campus da Penteada, 9020-105 Funchal, Madeira, Portugal”
Symbolizes that within the European Union the product must be collected separately at the product end-of-
life. Do not dispose of these products as unsorted municipal waste.
A UK Declaration of Conformity in accordance with GB UKCA standards has been made. The manufacturer
declares that the product supplied with this document is compliant with the provisions of the Electromagnetic
Compatibility Regulations 016, and where applicable, the Electrical Equipment (Safety) Regulations 2016
Directives.
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
No liability will be accepted by Vista for any errors or omissions in this information and reserves
the right to make changes to the product and its specification from time to time without prior notice.