Vitek VTC-BHOCRAZE User manual

VITEK
VITEK
FEATURES:
• 1/3” Progressive Scan CMOS Sensor
• 2.1 MegaPixel With full 1080p/720p HD-SDI (SMPTE292M) / EX-SDI
Output
• Up to 30fps live view@ 1920x1080 (1080p)
• MegaPixel IR Corrected 3-9mm (VTC-BHOCRAZE39) / 9-22mm (VTC-
BHOCRAZE922) Motorized Auto Focus Zoom Lens
• True Day/Night with Dual Filter Switch
• 16:9 Video format
• On-board Intelligence (OBI Technology) delivers Auto-Focus-Zoom by
tracking motion, then optically zooming into that area of the frame
• Fully programmable advanced WDR
• 40 850nm IR LEDs with up to 150’ IR range
• Integrated Cooling Fan
• Advanced OSD Functions: Motion Activated Pointing Zoom, Defog, Smart
Dynamic IR, BLC/HLC, Motion Deblur, Pixel Defect Compensation, Title Set,
Mirror, Flip, Lens Refresh, Lens Initialize, Home Position, DSS, LED ON/OFF
control
• 100% Pure Digital Transmission of video data
• Extended Range Beyond 1000’ with RG59U 95% Copper Braid Coax
• Heavy Duty IP68 rated water/vandal resistant aluminum construction
• 12VDC / 24VAC Dual Voltage Operation
VTC-BHOCRAZE
2.1MP HD-SDI / EX-SDI
Vandal Resistant AFZ/WDR
IR Bullet Camera

2 3
Safety Precaution
CAUTION: TO REDUCE THE RISK OF ELECTICAL
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
To prevent electrical shock and risk of fire hazards, do not expose this unit
to rain or moisture and only use specified power source..
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
their own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Main power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power interruptions, it is
recommended that the device be powered from an uninterruptible power supply
(UPS).
The symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electrical shock.

3
Safety Precaution
NOTICE
• The image used in this instruction manual are processed to help
comprehension and may differ from actual video of the camera.
• Avoid installing in areas where shock or vibration may occur.
• Pay attention to safety when running the connection cables and
make sure that the cables are not subject to heavy loads, kinks,
moisture or damage.
• Never open the device (no user serviceable parts inside). The
warranty becomes void if repairs are undertaken by
unauthorized persons.
• Maintenance and repair have to be carried out only by authorized
service centers.
• Use only a mild detergent to clean the housing.
• The camera should never be operated beyond the technical
specifications. This can lead to damaging the device and void
the warranty.
• The camera should never be operated in water.

4 5
Contents
p. 2~3
Safety Precaution
p. 4
Contents
p. 5~6
Features
p. 6
Package Includes
p. 7
Dimensions / Part Names
p. 8~10
Installation Instructions
p. 11~28
Operating Instructions
p. 29
Specifications
p. 30
On Cue VT-HDOCE Series
p. 31
Limited Product Warranty

5
Features
Key Features
• Full HD, 2.1 Mega Pixel, EX-SDI CAMERA, 1920x1080(30p/25p)
• Extended long reach HD Solution
• True WDR(Wide Dynamic Range)
• Improved Noise reduction with enhanced 3D-NR
• VTC-BHOCRAZE39: f=3~9mm, F1.2~F2.1 Day & Night Motorized Auto
Focus and Zoom lens (Optical 3x Auto focus zoom / Digital 32x zoom)
• VTC-BHOCRAZE922: f=9~22mm, F1.6~F2.3 Day & Night Motorized
Auto Focus and Zoom lens (Optical 2.4x Auto focus zoom / Digital 32x zoom)
• Dual ICR Switch
• Focusing Status Indicator on Screen
- ★(Blue) Focusing in process
- ★(White) Focusing Completed
• Various Zooming Technologies
- Smart Motion Zoom an Automatic zoom in/out when motion is detected
- Pointing Zoom which enables the zooming of any area within the FOV
- Preset Zoom, up to 4 presets
• Home Position setting
• Motion Detection, Privacy Mask, Defog, Sens-up(x32), BLC/HLC,
D-Zoom, H/V/HV Flip, Motion Deblur, Pixel Defect Compensation,
Lens Refresh, Lens Initialize
• ID / TITLE / ZOOM RATIO DISPLAY
• Enhanced Sensitivity by DSS technology
• EX-SDI or HD-SDI switchable
• Top performance at low light sensitivity (Sens-up On)
• OSD menu & Video sub-out for easy installation & maintenance.
• Circuit protection against faulty connection in power polarity
• Isolated power supply against ground loop problem
• Remote control via RS-485 (Pelco-D/P)
• Firmware update via RS-485
• Built-in 40 LEDs
• LED ON/OFF control
• Dual Window, One-touch 3-Axis locking bracket, Easy Installation Pad
• Built-in cooling Fan & Heating function
• 100% Pure Digital Transmission of video data
• Extended Range Beyond 1000’ with RG59U 95% Copper Braid Coax
• Heavy Duty IP68 rated water/vandal resistant aluminum construction
• 12VDC / 24VAC Dual Voltage Operation

6 7
Features
Package Includes
Mounting Template
General Operation
Instruction
Camera
General Description
• With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accept infrared light
• With 24VAC/12VDC dual power design,
- Offers the flexibility of installation
- Ensures the reliability
This camera realizes the natural and crisp image as you see the scene in front of
you by adopting Auto Focus Full HD(1920x1080p) camera module.
Torque Wrench:
3mm (1pc)
Video Sub-out
Cable (1pc)
Assembly Screw:
4 x 14mm (4pcs)
Mounting Screw:
4 x 30mm (4pcs)
Plastic Anchor:
6 x 30mm (4pcs)
Easy
Bracket
Cable Signal
Sticker Wiring Connector:
(1pc)

7
Part Names
Dimensions
(unit : inches)
LOCK/UNLOCK
SCREW
4.35
3.53
4.37
3.94
3.31
3.39
3.15
10.11
DUAL WINDOW
SUNSHIELD BOLT
SUNSHIELD
FRONT CASE
OSD Setup
CONTROL COVER
BRACKET
EASY
BRACKET
REAR CASE
POWER & VIDEO CABLE

8 9
Installation Instructions
Mounting Screw
: 4x30mm
Plastic Anchor
: 6x30mm
1
2
Torque Wrench
REAR VIEW
3
Cable exit
4
Assembly Screw
: 4x14mm
1. Place the mounting template at the installation position and drill the ceiling or
wall if needed. (*The easy bracket can not be installed on the ceiling)
2. Place the easy bracket on pre-drilled position and attach using mounting
screws(4x30mm). Skip this step when an easy bracket is not installed.
3. Route the power cable to the connecting place.
Hook up the camera bracket with the easy bracket as illustrated below.
4. Attach the camera bracket using the assembly screws (4x14mm).
Set the camera’s viewing angle.
5. Attach the sunshield to the camera unit and tighten the sunshield-bolt.

9
Installation Instructions
• Unlock the screw on the camera bracket through using the torque wrench supplied
• Set the camera’s viewing angle then lock the screw on the bracket.
Pan & Tilt adjustments
1) Pan limit:
Pan is limited to +/- 90°.
3) Inclination limit
(Horizontal image alignment): Inclination limited to +/-90° max.
2) Tilt limit:
Tilt is limited to 0°(2°) min ~ 90° max.
for wall (ceiling) installation respectively
with reference to the wall (ceiling) when
the inclination of camera module is 0°,
that is, the image is aligned horizontally.
■Adjustment of viewing angle
with one-touch 3-Axis bracket
Torque
wrench
Lock/Unlock
Screw
90° 90°
80°
90°
±90°
•on the wall
•on the ceiling

10 11
Installation Instructions
Power Supply Connections
l Make sure the power is removed before installation.
l Camera can work with either 24VAC or 12VDC, dual voltage power .
l Primary and secondary grounds are completely isolated to avoid possible
ground-loop problems
※ Attach the Signal Assignment Sticker
in a visible spot for wiring reference.
VIDEO (BNC)
AC24V/GND (Black wire)
AC24V/DC12V (Red wire)
RTX-/RS485 (Gray wire)
RTX+/RS485 (White wire)
In case that HD-SDI/EX-SDI Inputs are not supported by your monitor, please
use HD-SDI/EX-SDI Converter to connect HD-SDI/EX-SDI cable with Monitor