Vivo DESK-E-200W User manual

Instruction ManualInstruction Manual
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
White Electric Dual Motor Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
SKU: DESK-E-200W
https://vivo-us.com/products/desk-e-200w

2
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual and do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or
inappropriate use.
WARNING!
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
OPERATING INSTRUCTIONS: When the system is powered on, you will hear a beep and the existing desktop
height will be displayed on the control panel.
Upward and Downward Movement
Press and hold the up or down arrow until the desk reaches the desired height.
Memory Mode
To store a certain height in the controller’s memory, first press “M”. The letter “S-” will be displayed. Now
press “1”, “2” or “3” to store the current height in memory. Each number can store a dierent height. Once in
memory, you can recall any of the three height settings by pressing the corresponding button.
Reset Mode
While the unit is powered on, press the down arrow until the desk moves to the fully lowered position.
Restart the system by unplugging for at least 5 seconds and plug back in, then hold the down arrow until
RST is displayed. Continue holding the down arrow and the desk will move to the lowest position, then raise
slightly and stop to complete the reset process.
Anti-Collision Sensitivity Adjustment
Press and hold the up and down arrows together for 5 seconds to switch to the anti-collision sensitivity
adjustment. Sensitivity is set to A-3 (high) by default. Use the up and down arrows to scroll through A-0 (o),
A-1 (low), A-2 (medium) and A-3 (high). Wait 5 seconds, and the setting will be saved. With anti-collision on,
the desk will stop and reverse slightly to avoid damage.
OPERATING CONTROL PANEL

3
NOTES
• Self-protection function: The unit will enter a protective mode should the system operate
in excess of 2 minutes. The system will return to normal operation aer approximately 18
minutes.
• Over-current protection mode: While operating, should the load on the desk exceed rated
specifications, the system will enter into over-current protection mode to protect the system
from damage. When this happens, the desk will move downward slightly and come to a stop
with the current height displayed.
• Do NOT remove or reconnect power to reset the unit when in a protective “E01” or “E02” state,
as this may damage the electronics.
TROUBLESHOOTING
Raise desktop
slowly to keep
items stable.
Keep monitor and
laptop base fully on
the desktop.
Leave enough slack
in cable to allow for
full range of vertical
motion (15” / 38 cm).
Follow the cable
routing instructions to
avoid the potential to
pinch cables.
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
If the displayed height no longer matches the actual height, reset the desk by following the “Reset
Mode” directions.
If the desk stops moving and the display shows “E01” or “E02”, allow the desk to rest for at least 18
minutes before attempting to operate again.
If the desk is not operational, disconnect the power, motor and control panel from the control unit.
Aer waiting for at least 10 seconds, reconnect the motor and panel to the control unit, then reconnect
power.
If RSR/RST appears, an error has occurred and entered reset mode for protection; complete reset
process to clear error.

4
LAST UPDATED: 04/19/2021
REV3.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303