Vivo STAND-V100H/W User manual

Pneumatic Arm Single Ultra Wide Monitor
Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v100h
SKU: STAND-V100H/W
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
39.6lbs
(18kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
PACKAGE CONTENTS
TOOLS NEEDED
Phillips
Screwdriver
A (x1)
Base
B(x1)
Arm
C(x1)
Rear Cover
I (x1)
VESA Plate
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Clamp Brace
E(x1)
Grommet
Base Plate
F (x1)
Clamp Plate
G(x1)
Clamp Bracket
S-A (x2)
M10x63mm
Clamp Bolt
H (x1)
200x100
VESA Plate
S-B (x2)
M8x105mm
Carriage Bolt
M-A (x4)
M4x12mm
Screw
M-B (x4)
M5x12mm
M-C (x4)
M5 Washer
S-E (x4)
M4x8mm
Screw
J (x2)
Support Plate
S-C (x2)
M8 Washer
S-D (x2)
M8 Nut
S-F (x4)
M6x12mm
Screw
T-B (x1)
4mm Allen
Wrench
S-G (x1)
Spacer
S-H (x4)
M4 Nut
S-I (x1)
M8x25mm
Screws
S-J (x1)
Arm
Washer
T-A (x1)
Wrench
T-C (x1)
6mm Allen
Wrench

4
ASSEMBLY STEPS
STEP 1 - Option A - Clamp Mount
Attach Clamp Brace (D) to Base (A) using M6x12mm Screws (S-F), and tighten with 4mm Allen
Wrench (T-B). Insert M10x63mm Clamp Bolts (S-A) into Clamp Bracket (G) as shown, then place
Clamp Plate (F) on top of assembled clamp.
Install Clamp Bracket (G) to upper holes of Clamp Brace (D) for a desk thickness of 3/8” to 1-1/2”
(10 - 40mm), or to lower holes for a desk thickness of 1-1/2” to 3-1/4” (40 - 84mm).
T-B
S-F
D
A
G
G
D
T-C
D
F
S-A
G
Place assembled base on edge of desk and tighten clamp bolts evenly with 6mm Allen Wrench (T-C).

5
STEP 1 - Option B - Grommet
Place M8x105mm Carriage Bolt (S-B) into square holes in Grommet Base Plate (E). Attach
Grommet Base Plate to Base (A) using M6x12mm Screws (S-F), and tighten with 4mm Allen
Wrench (T-B)
T-B S-B
S-F
E
A
Place assembled base over cable grommet hole in desktop, and tighten using Support Plate (J),
M8 Washers (S-C) and M8 Nuts (S-D), and tighten with Wrench (T-A).
If a grommet hole isn’t present, drill two 3/8”
(10mm) holes 49mm apart through the desktop.
T-A
J
S-C
S-D

6
STEP 2
Insert the Arm (B) into the socket of the Base (A), then secure using the 4mm Allen Wrench (T-B) or a
flatblade screwdriver. Install Rear Cover (C) to Clamp Brace (D) if the clamp option was used.
B
A
T-B
C
D
Install Arm Washer (S-J) to the top of Arm (B).
S-J
B

7
STEP 3
I
S-G
S-I
B
T-C
Connect VESA Plate (I) to Arm (B) using Spacer (S-G), M8x25mm Screw (S-I), and 6mm Allen
Wrench (T-C). Ensure that hexagon side of Spacer is facing upward towards VESA Plate (I). Remove
Thumbscrew (I1) from back of VESA Plate (I). Separate Front VESA Plate (I2) from Back VESA Plate
(I3). Set aside.
I2
I3
I1

8
STEP 4
OPTION B: VESA 200x100
Install the 200x100 VESA Plate (H) to the VESA Plate (I) using the M4x8mm Screws (S-E) and M4
Nuts (S-H), tightening with Wrench (T-A) and a Phillips screwdriver. Mount assembled VESA plate
to monitor using M4x12mm Screws (M-A) or M5x12mm Screws (M-B) with M5 Washers (M-C),
making sure the rounded edges of the rear bracket are facing up.
OPTION A: VESA 75x75, 100x100
Install the VESA Plate (I) to monitor using M4x12mm
Screws (M-A) or M5x12mm Screws (M-B) with M5
Washers (M-C), making sure the rounded edges of
the rear bracket are facing up.
I
M-A
M-B
S-E
H
I
S-H T-A
M-A
M-B
M-C
M-C

9
While holding the arm in the horizontal position, adjust the gas spring tension using the
6mm Allen Wrench (T-C).
STEP 6
CAUTION - To avoid damage to the monitor
and mount, always keep the arm in a horizontal
position while making adjustments.
STEP 5
To mount the monitor, begin by lining up the tabs on Front VESA Plate (I2) with the slots on Back VESA
Plate (I3). Insert tabs into slots and re-install Thumbscrew (G1) into Back VESA Plate (G3) to secure.
I2
I3
I1
T-C

10
STEP 7
Remove cable covers from base and adjustable arm. Organize cables and reinstall cable covers to
base and adjustable arm.