Vivo STAND-V001O User manual

Pneumatic Arm Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001o
[email protected]om www.vivo-us.com 309-278-5303
SKU: STAND-V001O

2
PACKAGE CONTENTS
4.4-14.3lbs
(2-6.49kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
A (x1)
Arm
B(x1)
Bracket
C(x1)
Clamp
J (x1)
4mm Allen
Wrench
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x2)
M6x10
E(x3)
M6x12
F (x1)
Grommet
Base
G(x1)
Wingnut
H (x1)
Carriage Bolt
I (x1)
Support Plate
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x1)
5mm Allen
Wrench
M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
D5 Washer

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Mount bracket (B) to bottom of gas spring arm (A) using bolts (E). Tighten using 4mm allen key (J).
Attach clamp (C) to bracket (B) using bolts (D) and 4mm allen key (J). Mount according to thickness of
desktop. Secure stand to desktop by tightening clamp (C).
A
B
E
J
10-55mm
J
D
C
50-85mm
J
D
C
OR

4
STEP 1 (Continued)
OPTION B: Grommet Base Installation
For grommet hole mounting, place carriage bolt (H) through the center of grommet base (F). Mount
grommet base to bottom of gas spring arm (A) using bolts (E). Tighten using 4mm allen key (J). Run
carriage bolt (H) through grommet hole in desktop. Attach metal plate (I) and wingnut (G). Tighten
wingnut.
J
H
F
E
G
I

5
STEP 2
Attach two bolts (M-A or M-B) and washers (M-C) to top mounting holes of monitor, making sure to
leave 3mm of threads exposed. Align bolts (M-A, M-B) in VESA plate. Secure using two more bolts (M-A
or M-B) and washers (M-C) in the bottom two holes. Tighten all four bolts using the phillips screwdriver
end of 5mm allen key (K).
M- A
M- B
M- C
3mm
K
M- A
M- B
M- C
K
STEP 3
Adjust tension in gas spring arm (A) and monitor bracket using 5mm allen key (K).
KK

6
STEP 4
Remove bottom plastic covers from gas spring arm (A) using the phillips screwdriver end of 5mm
allen key (K).
STEP 5
Run cables from monitor through bottom of gas spring arm (A). Reattach plastic covers as shown in
diagram.
1
2
K
K1
2
K
1
2
K
12

7
Adjust as Desired
360°
180°
+90°
-45°
360°
360°

LAST UPDATED: 10/28/2019
Open Monday-Friday from 7:00am-7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times.
If any parts are received damaged or defective, please contact us.
We are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]
www.vivo-us.com
309-278-5303
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
AVG. RESOLUTION TIME (within oice hrs): < 15 M